container memif¶
10ge2p1x710-eth-l2xcbase-eth-2memif-1dcr-mrr¶
Raw results L2XC test cases
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv4 for L2 cross connect.
- [Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 cross- connect. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel. Container is connected to VPP via Memif interface. Container is running same VPP version as running on DUT. Container is limited via cgroup to use 3 cores allocated from pool of isolated CPUs. There are no memory contraints.
- [Ver] TG verification: In MaxReceivedRate test TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 254 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
Name | Status |
---|---|
64b-2t1c-eth-l2xcbase-eth-2memif-1dcr-mrr |
|
64b-4t2c-eth-l2xcbase-eth-2memif-1dcr-mrr |
|
64b-8t4c-eth-l2xcbase-eth-2memif-1dcr-mrr |
|
1518b-2t1c-eth-l2xcbase-eth-2memif-1dcr-mrr |
|
1518b-4t2c-eth-l2xcbase-eth-2memif-1dcr-mrr |
|
1518b-8t4c-eth-l2xcbase-eth-2memif-1dcr-mrr |
|
9000b-2t1c-eth-l2xcbase-eth-2memif-1dcr-mrr |
|
9000b-4t2c-eth-l2xcbase-eth-2memif-1dcr-mrr |
|
9000b-8t4c-eth-l2xcbase-eth-2memif-1dcr-mrr | timeout, not up [u’TenGigabitEthernet18/0/3’] |
imix-2t1c-eth-l2xcbase-eth-2memif-1dcr-mrr |
|
imix-4t2c-eth-l2xcbase-eth-2memif-1dcr-mrr |
|
imix-8t4c-eth-l2xcbase-eth-2memif-1dcr-mrr | timeout, not up [u’TenGigabitEthernet18/0/3’] |
ip4¶
10ge2p1x710-ethip4-ip4base-copwhtlistbase-mrr¶
Raw results IPv4 whitelist test cases
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv4 for IPv4 routing.
- [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv4 routing, two static IPv4 /24 routes and IPv4 COP security whitelist ingress /24 filter entries applied on links TG - DUT1 and DUT2 - TG. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel.
- [Ver] TG verification: In MaxReceivedRate test TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- [Ref] Applicable standard specifications: RFC2544.
Name | Status |
---|---|
64b-2t1c-ethip4-ip4base-copwhtlistbase-mrr |
|
64b-4t2c-ethip4-ip4base-copwhtlistbase-mrr |
|
64b-8t4c-ethip4-ip4base-copwhtlistbase-mrr |
|
1518b-2t1c-ethip4-ip4base-copwhtlistbase-mrr |
|
1518b-4t2c-ethip4-ip4base-copwhtlistbase-mrr |
|
1518b-8t4c-ethip4-ip4base-copwhtlistbase-mrr | timeout, not up [u’TenGigabitEthernet18/0/3’] |
9000b-2t1c-ethip4-ip4base-copwhtlistbase-mrr |
|
9000b-4t2c-ethip4-ip4base-copwhtlistbase-mrr | timeout, not up [u’TenGigabitEthernet18/0/3’] |
9000b-8t4c-ethip4-ip4base-copwhtlistbase-mrr | timeout, not up [u’TenGigabitEthernet18/0/0’] |
imix-2t1c-ethip4-ip4base-copwhtlistbase-mrr |
|
imix-4t2c-ethip4-ip4base-copwhtlistbase-mrr | timeout, not up [u’TenGigabitEthernet18/0/3’] |
imix-8t4c-ethip4-ip4base-copwhtlistbase-mrr |
|
10ge2p1x710-ethip4-ip4base-iacldstbase-mrr¶
Raw results IPv4 iAcl whitelist test cases
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv4 for IPv4 routing.
- [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv4 routing, two static IPv4 /24 routes and IPv4 iAcl security whitelist ingress /24 filter entries applied on links TG - DUT1 and DUT2 - TG. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel.
- [Ver] TG verification: In MaxReceivedRate tests TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv6 header and generated payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- [Ref] Applicable standard specifications: RFC2544.
Name | Status |
---|---|
64b-2t1c-ethip4-ip4base-iacldstbase-mrr | timeout, not up [u’TenGigabitEthernet18/0/3’] |
64b-4t2c-ethip4-ip4base-iacldstbase-mrr |
|
64b-8t4c-ethip4-ip4base-iacldstbase-mrr | timeout, not up [u’TenGigabitEthernet18/0/3’] |
1518b-2t1c-ethip4-ip4base-iacldstbase-mrr |
|
1518b-4t2c-ethip4-ip4base-iacldstbase-mrr |
|
1518b-8t4c-ethip4-ip4base-iacldstbase-mrr |
|
9000b-2t1c-ethip4-ip4base-iacldstbase-mrr |
|
9000b-4t2c-ethip4-ip4base-iacldstbase-mrr |
|
9000b-8t4c-ethip4-ip4base-iacldstbase-mrr | timeout, not up [u’TenGigabitEthernet18/0/3’] |
imix-2t1c-ethip4-ip4base-iacldstbase-mrr |
|
imix-4t2c-ethip4-ip4base-iacldstbase-mrr |
|
imix-8t4c-ethip4-ip4base-iacldstbase-mrr | timeout, not up [u’TenGigabitEthernet18/0/3’] |
10ge2p1x710-ethip4-ip4base-ipolicemarkbase-mrr¶
Raw results IPv4 policer test cases
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv4 for IPv4 routing.
- [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv4 routing and two static IPv4 /24 route entries and policer with 2R3C color-aware configuration. Policer is applied on links TG - DUT1 and DUT2 - TG. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel.
- [Ver] TG verification: In MaxReceivedRate tests TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv6 header and generated payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- [Ref] Applicable standard specifications: RFC2544, RFC2698.
Name | Status |
---|---|
64b-2t1c-ethip4-ip4base-ipolicemarkbase-mrr |
|
64b-4t2c-ethip4-ip4base-ipolicemarkbase-mrr |
|
64b-8t4c-ethip4-ip4base-ipolicemarkbase-mrr | timeout, not up [u’TenGigabitEthernet18/0/3’] |
1518b-2t1c-ethip4-ip4base-ipolicemarkbase-mrr | timeout, not up [u’TenGigabitEthernet18/0/3’] |
1518b-4t2c-ethip4-ip4base-ipolicemarkbase-mrr | timeout, not up [u’TenGigabitEthernet18/0/2’] |
1518b-8t4c-ethip4-ip4base-ipolicemarkbase-mrr | timeout, not up [u’TenGigabitEthernet18/0/2’, u’TenGigabitEthernet18/0/3’] |
9000b-2t1c-ethip4-ip4base-ipolicemarkbase-mrr |
|
9000b-4t2c-ethip4-ip4base-ipolicemarkbase-mrr |
|
9000b-8t4c-ethip4-ip4base-ipolicemarkbase-mrr |
|
imix-2t1c-ethip4-ip4base-ipolicemarkbase-mrr |
|
imix-4t2c-ethip4-ip4base-ipolicemarkbase-mrr |
|
imix-8t4c-ethip4-ip4base-ipolicemarkbase-mrr | timeout, not up [u’TenGigabitEthernet18/0/3’] |
10ge2p1x710-ethip4-ip4base-mrr¶
Raw results IPv4 routing test cases
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv4 for IPv4 routing.
- [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv4 routing and two static IPv4 /24 route entries. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel.
- [Ver] TG verification: In MaxReceivedRate test TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- [Ref] Applicable standard specifications: RFC2544.
Name | Status |
---|---|
64b-2t1c-ethip4-ip4base-mrr |
|
64b-4t2c-ethip4-ip4base-mrr | timeout, not up [u’TenGigabitEthernet18/0/2’] |
64b-8t4c-ethip4-ip4base-mrr |
|
1518b-2t1c-ethip4-ip4base-mrr |
|
1518b-4t2c-ethip4-ip4base-mrr |
|
1518b-8t4c-ethip4-ip4base-mrr |
|
9000b-2t1c-ethip4-ip4base-mrr |
|
9000b-4t2c-ethip4-ip4base-mrr |
|
9000b-8t4c-ethip4-ip4base-mrr |
|
imix-2t1c-ethip4-ip4base-mrr |
|
imix-4t2c-ethip4-ip4base-mrr | timeout, not up [u’TenGigabitEthernet18/0/0’] |
imix-8t4c-ethip4-ip4base-mrr | timeout, not up [u’TenGigabitEthernet18/0/3’] |
10ge2p1x710-ethip4-ip4scale200k-mrr¶
Raw results IPv4 routing test cases
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv4 for IPv4 routing.
- [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv4 routing and 2x100k static IPv4 /32 route entries. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel.
- [Ver] TG verification: In MaxReceivedRate test TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- [Ref] Applicable standard specifications: RFC2544.
Name | Status |
---|---|
64b-2t1c-ethip4-ip4scale200k-mrr | timeout, not up [u’TenGigabitEthernet18/0/2’] |
64b-4t2c-ethip4-ip4scale200k-mrr | timeout, not up [u’TenGigabitEthernet18/0/2’, u’TenGigabitEthernet18/0/3’] |
64b-8t4c-ethip4-ip4scale200k-mrr | timeout, not up [u’TenGigabitEthernet18/0/2’, u’TenGigabitEthernet18/0/3’] |
1518b-2t1c-ethip4-ip4scale200k-mrr |
|
1518b-4t2c-ethip4-ip4scale200k-mrr |
|
1518b-8t4c-ethip4-ip4scale200k-mrr | timeout, not up [u’TenGigabitEthernet18/0/3’] |
9000b-2t1c-ethip4-ip4scale200k-mrr |
|
9000b-4t2c-ethip4-ip4scale200k-mrr |
|
9000b-8t4c-ethip4-ip4scale200k-mrr |
|
imix-2t1c-ethip4-ip4scale200k-mrr |
|
imix-4t2c-ethip4-ip4scale200k-mrr |
|
imix-8t4c-ethip4-ip4scale200k-mrr | timeout, not up [u’TenGigabitEthernet18/0/0’] |
10ge2p1x710-ethip4-ip4scale20k-mrr¶
Raw results IPv4 routing test cases
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv4 for IPv4 routing.
- [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv4 routing and 2x100k static IPv4 /32 route entries. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel.
- [Ver] TG verification: In MaxReceivedRate test TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- [Ref] Applicable standard specifications: RFC2544.
Name | Status |
---|---|
64b-2t1c-ethip4-ip4scale20k-mrr | timeout, not up [u’TenGigabitEthernet18/0/0’] |
64b-4t2c-ethip4-ip4scale20k-mrr |
|
64b-8t4c-ethip4-ip4scale20k-mrr | timeout, not up [u’TenGigabitEthernet18/0/3’] |
1518b-2t1c-ethip4-ip4scale20k-mrr |
|
1518b-4t2c-ethip4-ip4scale20k-mrr | timeout, not up [u’TenGigabitEthernet18/0/2’] |
1518b-8t4c-ethip4-ip4scale20k-mrr | timeout, not up [u’TenGigabitEthernet18/0/3’] |
9000b-2t1c-ethip4-ip4scale20k-mrr |
|
9000b-4t2c-ethip4-ip4scale20k-mrr | timeout, not up [u’TenGigabitEthernet18/0/3’] |
9000b-8t4c-ethip4-ip4scale20k-mrr |
|
imix-2t1c-ethip4-ip4scale20k-mrr |
|
imix-4t2c-ethip4-ip4scale20k-mrr |
|
imix-8t4c-ethip4-ip4scale20k-mrr | timeout, not up [u’TenGigabitEthernet18/0/3’] |
10ge2p1x710-ethip4-ip4scale2m-mrr¶
Raw results IPv4 routing test cases
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv4 for IPv4 routing.
- [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv4 routing and 2x100k static IPv4 /32 route entries. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel.
- [Ver] TG verification: In MaxReceivedRate test TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- [Ref] Applicable standard specifications: RFC2544.
Name | Status |
---|---|
64b-2t1c-ethip4-ip4scale2m-mrr |
|
64b-4t2c-ethip4-ip4scale2m-mrr |
|
64b-8t4c-ethip4-ip4scale2m-mrr |
|
1518b-2t1c-ethip4-ip4scale2m-mrr |
|
1518b-4t2c-ethip4-ip4scale2m-mrr |
|
1518b-8t4c-ethip4-ip4scale2m-mrr | timeout, not up [u’TenGigabitEthernet18/0/3’] |
9000b-2t1c-ethip4-ip4scale2m-mrr | timeout, not up [u’TenGigabitEthernet18/0/0’] |
9000b-4t2c-ethip4-ip4scale2m-mrr |
|
9000b-8t4c-ethip4-ip4scale2m-mrr |
|
imix-2t1c-ethip4-ip4scale2m-mrr |
|
imix-4t2c-ethip4-ip4scale2m-mrr | timeout, not up [u’TenGigabitEthernet18/0/0’] |
imix-8t4c-ethip4-ip4scale2m-mrr |
|
10ge2p1x710-ethip4udp-ip4base-iacl1sf-10kflows-mrr¶
Raw results IPv4 test cases with ACL
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
- [Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with 2p10GE NIC X710 by Intel.
- [Ver] TG verification: In MaxReceivedRate test TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- [Ref] Applicable standard specifications: RFC2544.
Name | Status |
---|---|
64b-2t1c-ethip4udp-ip4base-iacl1sf-10kflows-mrr |
|
64b-4t2c-ethip4udp-ip4base-iacl1sf-10kflows-mrr |
|
64b-8t4c-ethip4udp-ip4base-iacl1sf-10kflows-mrr | timeout, not up [u’TenGigabitEthernet18/0/3’] |
1518b-2t1c-ethip4udp-ip4base-iacl1sf-10kflows-mrr |
|
1518b-4t2c-ethip4udp-ip4base-iacl1sf-10kflows-mrr | timeout, not up [u’TenGigabitEthernet18/0/3’] |
1518b-8t4c-ethip4udp-ip4base-iacl1sf-10kflows-mrr |
|
9000b-2t1c-ethip4udp-ip4base-iacl1sf-10kflows-mrr |
|
9000b-4t2c-ethip4udp-ip4base-iacl1sf-10kflows-mrr | timeout, not up [u’TenGigabitEthernet18/0/2’, u’TenGigabitEthernet18/0/3’] |
9000b-8t4c-ethip4udp-ip4base-iacl1sf-10kflows-mrr |
|
imix-2t1c-ethip4udp-ip4base-iacl1sf-10kflows-mrr |
|
imix-4t2c-ethip4udp-ip4base-iacl1sf-10kflows-mrr |
|
imix-8t4c-ethip4udp-ip4base-iacl1sf-10kflows-mrr | timeout, not up [u’TenGigabitEthernet18/0/3’] |
10ge2p1x710-ethip4udp-ip4base-iacl1sl-10kflows-mrr¶
Raw results IPv4 test cases with ACL
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
- [Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with 2p10GE NIC X710 by Intel.
- [Ver] TG verification: In MaxReceivedRate test TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- [Ref] Applicable standard specifications: RFC2544.
Name | Status |
---|---|
64b-2t1c-ethip4udp-ip4base-iacl1sl-10kflows-mrr |
|
64b-4t2c-ethip4udp-ip4base-iacl1sl-10kflows-mrr |
|
64b-8t4c-ethip4udp-ip4base-iacl1sl-10kflows-mrr | timeout, not up [u’TenGigabitEthernet18/0/3’] |
1518b-2t1c-ethip4udp-ip4base-iacl1sl-10kflows-mrr |
|
1518b-4t2c-ethip4udp-ip4base-iacl1sl-10kflows-mrr |
|
1518b-8t4c-ethip4udp-ip4base-iacl1sl-10kflows-mrr |
|
9000b-2t1c-ethip4udp-ip4base-iacl1sl-10kflows-mrr |
|
9000b-4t2c-ethip4udp-ip4base-iacl1sl-10kflows-mrr |
|
9000b-8t4c-ethip4udp-ip4base-iacl1sl-10kflows-mrr | timeout, not up [u’TenGigabitEthernet18/0/3’] |
imix-2t1c-ethip4udp-ip4base-iacl1sl-10kflows-mrr |
|
imix-4t2c-ethip4udp-ip4base-iacl1sl-10kflows-mrr |
|
imix-8t4c-ethip4udp-ip4base-iacl1sl-10kflows-mrr |
|
10ge2p1x710-ethip4udp-ip4base-iacl50sf-10kflows-mrr¶
Raw results IPv4 test cases with ACL
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
- [Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with 2p10GE NIC X710 by Intel.
- [Ver] TG verification: In MaxReceivedRate test TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- [Ref] Applicable standard specifications: RFC2544.
Name | Status |
---|---|
64b-2t1c-ethip4udp-ip4base-iacl50sf-10kflows-mrr |
|
64b-4t2c-ethip4udp-ip4base-iacl50sf-10kflows-mrr |
|
64b-8t4c-ethip4udp-ip4base-iacl50sf-10kflows-mrr |
|
1518b-2t1c-ethip4udp-ip4base-iacl50sf-10kflows-mrr |
|
1518b-4t2c-ethip4udp-ip4base-iacl50sf-10kflows-mrr |
|
1518b-8t4c-ethip4udp-ip4base-iacl50sf-10kflows-mrr | timeout, not up [u’TenGigabitEthernet18/0/3’] |
9000b-2t1c-ethip4udp-ip4base-iacl50sf-10kflows-mrr | timeout, not up [u’TenGigabitEthernet18/0/3’] |
9000b-4t2c-ethip4udp-ip4base-iacl50sf-10kflows-mrr |
|
9000b-8t4c-ethip4udp-ip4base-iacl50sf-10kflows-mrr |
|
imix-2t1c-ethip4udp-ip4base-iacl50sf-10kflows-mrr | timeout, not up [u’TenGigabitEthernet18/0/2’] |
imix-4t2c-ethip4udp-ip4base-iacl50sf-10kflows-mrr | timeout, not up [u’TenGigabitEthernet18/0/3’] |
imix-8t4c-ethip4udp-ip4base-iacl50sf-10kflows-mrr |
|
10ge2p1x710-ethip4udp-ip4base-iacl50sl-10kflows-mrr¶
Raw results IPv4 test cases with ACL
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
- [Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with 2p10GE NIC X710 by Intel.
- [Ver] TG verification: In MaxReceivedRate test TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- [Ref] Applicable standard specifications: RFC2544.
Name | Status |
---|---|
64b-2t1c-ethip4udp-ip4base-iacl50sl-10kflows-mrr |
|
64b-4t2c-ethip4udp-ip4base-iacl50sl-10kflows-mrr |
|
64b-8t4c-ethip4udp-ip4base-iacl50sl-10kflows-mrr | timeout, not up [u’TenGigabitEthernet18/0/3’] |
1518b-2t1c-ethip4udp-ip4base-iacl50sl-10kflows-mrr |
|
1518b-4t2c-ethip4udp-ip4base-iacl50sl-10kflows-mrr |
|
1518b-8t4c-ethip4udp-ip4base-iacl50sl-10kflows-mrr |
|
9000b-2t1c-ethip4udp-ip4base-iacl50sl-10kflows-mrr | timeout, not up [u’TenGigabitEthernet18/0/0’] |
9000b-4t2c-ethip4udp-ip4base-iacl50sl-10kflows-mrr | timeout, not up [u’TenGigabitEthernet18/0/3’] |
9000b-8t4c-ethip4udp-ip4base-iacl50sl-10kflows-mrr |
|
imix-2t1c-ethip4udp-ip4base-iacl50sl-10kflows-mrr |
|
imix-4t2c-ethip4udp-ip4base-iacl50sl-10kflows-mrr |
|
imix-8t4c-ethip4udp-ip4base-iacl50sl-10kflows-mrr |
|
10ge2p1x710-ethip4udp-ip4base-nat44-mrr¶
Raw results NAT44 performance test cases
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv4-UDP for IPv4 routing.
- [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv4 routing and two static IPv4 /24 and IPv4/20 route entries. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel.
- [Ver] TG verification: In MaxReceivedRate test TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- [Ref] Applicable standard specifications: RFC2544.
Name | Status |
---|---|
64b-2t1c-ethip4udp-ip4base-nat44-mrr |
|
64b-4t2c-ethip4udp-ip4base-nat44-mrr |
|
64b-8t4c-ethip4udp-ip4base-nat44-mrr |
|
1518b-2t1c-ethip4udp-ip4base-nat44-mrr |
|
1518b-4t2c-ethip4udp-ip4base-nat44-mrr |
|
1518b-8t4c-ethip4udp-ip4base-nat44-mrr |
|
9000b-2t1c-ethip4udp-ip4base-nat44-mrr |
|
9000b-4t2c-ethip4udp-ip4base-nat44-mrr | timeout, not up [u’TenGigabitEthernet18/0/3’] |
9000b-8t4c-ethip4udp-ip4base-nat44-mrr |
|
imix-2t1c-ethip4udp-ip4base-nat44-mrr |
|
imix-4t2c-ethip4udp-ip4base-nat44-mrr |
|
imix-8t4c-ethip4udp-ip4base-nat44-mrr | timeout, not up [u’TenGigabitEthernet18/0/3’] |
10ge2p1x710-ethip4udp-ip4scale1000-udpsrcscale15-nat44-mrr¶
Raw results NAT44 performance test cases
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv4-UDP for IPv4 routing.
- [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv4 routing and two static IPv4 /24 and IPv4/20 route entries. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel.
- [Ver] TG verification: In MaxReceivedRate test TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- [Ref] Applicable standard specifications: RFC2544.
Name | Status |
---|---|
64b-2t1c-ethip4udp-ip4scale1000-udpsrcscale15-nat44-mrr |
|
64b-4t2c-ethip4udp-ip4scale1000-udpsrcscale15-nat44-mrr |
|
64b-8t4c-ethip4udp-ip4scale1000-udpsrcscale15-nat44-mrr | timeout, not up [u’TenGigabitEthernet18/0/2’] |
1518b-2t1c-ethip4udp-ip4scale1000-udpsrcscale15-nat44-mrr | timeout, not up [u’TenGigabitEthernet18/0/0’] |
1518b-4t2c-ethip4udp-ip4scale1000-udpsrcscale15-nat44-mrr |
|
1518b-8t4c-ethip4udp-ip4scale1000-udpsrcscale15-nat44-mrr | timeout, not up [u’TenGigabitEthernet18/0/3’] |
9000b-2t1c-ethip4udp-ip4scale1000-udpsrcscale15-nat44-mrr |
|
9000b-4t2c-ethip4udp-ip4scale1000-udpsrcscale15-nat44-mrr |
|
9000b-8t4c-ethip4udp-ip4scale1000-udpsrcscale15-nat44-mrr | timeout, not up [u’TenGigabitEthernet18/0/3’] |
imix-2t1c-ethip4udp-ip4scale1000-udpsrcscale15-nat44-mrr |
|
imix-4t2c-ethip4udp-ip4scale1000-udpsrcscale15-nat44-mrr | timeout, not up [u’TenGigabitEthernet18/0/3’] |
imix-8t4c-ethip4udp-ip4scale1000-udpsrcscale15-nat44-mrr |
|
ip4 tunnels¶
10ge2p1x710-ethip4lispip4-ip4base-mrr¶
Raw results Lisp test cases
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv4-LISP-IPv4 on DUT1-DUT2, Eth-IPv4 on TG-DUTn for IPv4 routing over LISPoIPv4 tunnel.
- [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv4 routing and static routes. LISPoIPv4 tunnel is configured between DUT1 and DUT2. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel.
- [Ver] TG verification: In MaxReceivedRate test TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- [Ref] Applicable standard specifications: RFC6830.
Name | Status |
---|---|
64b-2t1c-ethip4lispip4-ip4base-mrr |
|
64b-4t2c-ethip4lispip4-ip4base-mrr |
|
64b-8t4c-ethip4lispip4-ip4base-mrr |
|
1518b-2t1c-ethip4lispip4-ip4base-mrr |
|
1518b-4t2c-ethip4lispip4-ip4base-mrr |
|
1518b-8t4c-ethip4lispip4-ip4base-mrr | timeout, not up [u’TenGigabitEthernet18/0/3’] |
9000b-2t1c-ethip4lispip4-ip4base-mrr |
|
9000b-4t2c-ethip4lispip4-ip4base-mrr | timeout, not up [u’TenGigabitEthernet18/0/2’, u’TenGigabitEthernet18/0/3’] |
9000b-8t4c-ethip4lispip4-ip4base-mrr |
|
imix-2t1c-ethip4lispip4-ip4base-mrr |
|
imix-4t2c-ethip4lispip4-ip4base-mrr |
|
imix-8t4c-ethip4lispip4-ip4base-mrr | timeout, not up [u’TenGigabitEthernet18/0/2’, u’TenGigabitEthernet18/0/3’] |
10ge2p1x710-ethip4vxlan-l2bdbasemaclrn-mrr¶
Raw results L2BD with VXLANoIPv4 test cases
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv4 for L2 bridge domain on TG-DUTn. Eth-IPv4-VXLAN-Eth-IPv4 is applied on link between DUT1 and DUT2.
- [Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 bridge domain. VXLAN tunnels are configured between L2BDs on DUT1 and DUT2. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel.
- [Ver] TG verification: In MaxReceivedRate test TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- [Ref] Applicable standard specifications: RFC2544, RFC7348.
Name | Status |
---|---|
64b-2t1c-ethip4vxlan-l2bdbasemaclrn-mrr |
|
64b-4t2c-ethip4vxlan-l2bdbasemaclrn-mrr | timeout, not up [u’TenGigabitEthernet18/0/3’] |
64b-8t4c-ethip4vxlan-l2bdbasemaclrn-mrr | timeout, not up [u’TenGigabitEthernet18/0/2’, u’TenGigabitEthernet18/0/3’] |
1518b-2t1c-ethip4vxlan-l2bdbasemaclrn-mrr | timeout, not up [u’TenGigabitEthernet18/0/3’] |
1518b-4t2c-ethip4vxlan-l2bdbasemaclrn-mrr | timeout, not up [u’TenGigabitEthernet18/0/0’] |
1518b-8t4c-ethip4vxlan-l2bdbasemaclrn-mrr |
|
9000b-2t1c-ethip4vxlan-l2bdbasemaclrn-mrr |
|
9000b-4t2c-ethip4vxlan-l2bdbasemaclrn-mrr | timeout, not up [u’TenGigabitEthernet18/0/3’] |
9000b-8t4c-ethip4vxlan-l2bdbasemaclrn-mrr |
|
imix-2t1c-ethip4vxlan-l2bdbasemaclrn-mrr |
|
imix-4t2c-ethip4vxlan-l2bdbasemaclrn-mrr |
|
imix-8t4c-ethip4vxlan-l2bdbasemaclrn-mrr | timeout, not up [u’TenGigabitEthernet18/0/3’] |
10ge2p1x710-ethip4vxlan-l2xcbase-mrr¶
Raw results L2XC with VXLANoIPv4 test cases
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv4 for L2 cross-connect on TG-DUTn. Eth-IPv4-VXLAN-Eth-IPv4 is applied on link between DUT1 and DUT2.
- [Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 cross- connect. VXLAN tunnels are configured between L2XCs on DUT1 and DUT2. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel.
- [Ver] TG verification: In MaxReceivedRate test TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- [Ref] Applicable standard specifications: RFC2544, RFC7348.
Name | Status |
---|---|
64b-2t1c-ethip4vxlan-l2xcbase-mrr |
|
64b-4t2c-ethip4vxlan-l2xcbase-mrr | timeout, not up [u’TenGigabitEthernet18/0/3’] |
64b-8t4c-ethip4vxlan-l2xcbase-mrr |
|
1518b-2t1c-ethip4vxlan-l2xcbase-mrr |
|
1518b-4t2c-ethip4vxlan-l2xcbase-mrr | timeout, not up [u’TenGigabitEthernet18/0/3’] |
1518b-8t4c-ethip4vxlan-l2xcbase-mrr |
|
9000b-2t1c-ethip4vxlan-l2xcbase-mrr |
|
9000b-4t2c-ethip4vxlan-l2xcbase-mrr |
|
9000b-8t4c-ethip4vxlan-l2xcbase-mrr | timeout, not up [u’TenGigabitEthernet18/0/3’] |
imix-2t1c-ethip4vxlan-l2xcbase-mrr |
|
imix-4t2c-ethip4vxlan-l2xcbase-mrr | timeout, not up [u’TenGigabitEthernet18/0/2’] |
imix-8t4c-ethip4vxlan-l2xcbase-mrr | timeout, not up [u’TenGigabitEthernet18/0/3’] |
ip6¶
10ge2p1x710-ethip6-ip6base-copwhtlistbase-mrr¶
Raw results IPv6 whitelist test cases
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv6 for IPv6 routing.
- [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv6 routing, two static IPv6 /64 routes and IPv6 COP security whitelist ingress /64 filter entries applied on links TG - DUT1 and DUT2 - TG. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel.
- [Ver] TG verification: In MaxReceivedRate tests TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv6 header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- [Ref] Applicable standard specifications: RFC2544.
Name | Status |
---|---|
78b-2t1c-ethip6-ip6base-copwhtlistbase-mrr | timeout, not up [u’TenGigabitEthernet18/0/2’] |
78b-4t2c-ethip6-ip6base-copwhtlistbase-mrr |
|
78b-8t4c-ethip6-ip6base-copwhtlistbase-mrr | timeout, not up [u’TenGigabitEthernet18/0/3’] |
1518b-2t1c-ethip6-ip6base-copwhtlistbase-mrr |
|
1518b-4t2c-ethip6-ip6base-copwhtlistbase-mrr |
|
1518b-8t4c-ethip6-ip6base-copwhtlistbase-mrr |
|
9000b-2t1c-ethip6-ip6base-copwhtlistbase-mrr | timeout, not up [u’TenGigabitEthernet18/0/0’] |
9000b-4t2c-ethip6-ip6base-copwhtlistbase-mrr |
|
9000b-8t4c-ethip6-ip6base-copwhtlistbase-mrr | timeout, not up [u’TenGigabitEthernet18/0/3’] |
imix-2t1c-ethip6-ip6base-copwhtlistbase-mrr |
|
imix-4t2c-ethip6-ip6base-copwhtlistbase-mrr | timeout, not up [u’TenGigabitEthernet18/0/0’] |
imix-8t4c-ethip6-ip6base-copwhtlistbase-mrr |
|
10ge2p1x710-ethip6-ip6base-iacldstbase-mrr¶
Raw results IPv6 iAcl whitelist test cases
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv6 for IPv6 routing.
- [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv6 routing, two static IPv6 /64 routes and IPv6 iAcl security whitelist ingress /64 filter entries applied on links TG - DUT1 and DUT2 - TG. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel.
- [Ver] TG verification: In MaxReceivedRate tests TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv6 header and generated payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- [Ref] Applicable standard specifications: RFC2544.
Name | Status |
---|---|
78b-2t1c-ethip6-ip6base-iacldstbase-mrr |
|
78b-4t2c-ethip6-ip6base-iacldstbase-mrr |
|
78b-8t4c-ethip6-ip6base-iacldstbase-mrr | timeout, not up [u’TenGigabitEthernet18/0/3’] |
1518b-2t1c-ethip6-ip6base-iacldstbase-mrr |
|
1518b-4t2c-ethip6-ip6base-iacldstbase-mrr |
|
1518b-8t4c-ethip6-ip6base-iacldstbase-mrr |
|
9000b-2t1c-ethip6-ip6base-iacldstbase-mrr |
|
9000b-4t2c-ethip6-ip6base-iacldstbase-mrr |
|
9000b-8t4c-ethip6-ip6base-iacldstbase-mrr | timeout, not up [u’TenGigabitEthernet18/0/3’] |
imix-2t1c-ethip6-ip6base-iacldstbase-mrr |
|
imix-4t2c-ethip6-ip6base-iacldstbase-mrr |
|
imix-8t4c-ethip6-ip6base-iacldstbase-mrr |
|
10ge2p1x710-ethip6-ip6base-mrr¶
Raw results IPv6 routing test cases
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv6 for IPv6 routing.
- [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv6 routing and two static IPv6 /64 route entries. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel.
- [Ver] TG verification: In MaxReceivedRate test TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv6 header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- [Ref] Applicable standard specifications: RFC2544.
Name | Status |
---|---|
78b-2t1c-ethip6-ip6base-mrr | timeout, not up [u’TenGigabitEthernet18/0/0’] |
78b-4t2c-ethip6-ip6base-mrr | timeout, not up [u’TenGigabitEthernet18/0/0’] |
78b-8t4c-ethip6-ip6base-mrr |
|
1518b-2t1c-ethip6-ip6base-mrr |
|
1518b-4t2c-ethip6-ip6base-mrr |
|
1518b-8t4c-ethip6-ip6base-mrr | timeout, not up [u’TenGigabitEthernet18/0/3’] |
9000b-2t1c-ethip6-ip6base-mrr |
|
9000b-4t2c-ethip6-ip6base-mrr | timeout, not up [u’TenGigabitEthernet18/0/3’] |
9000b-8t4c-ethip6-ip6base-mrr |
|
imix-2t1c-ethip6-ip6base-mrr |
|
imix-4t2c-ethip6-ip6base-mrr |
|
imix-8t4c-ethip6-ip6base-mrr |
|
10ge2p1x710-ethip6-ip6scale200k-mrr¶
Raw results IPv6 routing test cases
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv6 for IPv6 routing.
- [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv6 routing and 2x100k static IPv6 /64 route entries. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel.
- [Ver] TG verification: In MaxReceivedRate tests TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100k flows per flow-group) with all packets containing Ethernet header, IPv6 header withq IP and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv6 destination address) field is applied to both streams.
- [Ref] Applicable standard specifications: RFC2544.
Name | Status |
---|---|
78b-2t1c-ethip6-ip6scale200k-mrr |
|
78b-4t2c-ethip6-ip6scale200k-mrr | timeout, not up [u’TenGigabitEthernet18/0/3’] |
78b-8t4c-ethip6-ip6scale200k-mrr |
|
1518b-2t1c-ethip6-ip6scale200k-mrr |
|
1518b-4t2c-ethip6-ip6scale200k-mrr |
|
1518b-8t4c-ethip6-ip6scale200k-mrr |
|
9000b-2t1c-ethip6-ip6scale200k-mrr |
|
9000b-4t2c-ethip6-ip6scale200k-mrr |
|
9000b-8t4c-ethip6-ip6scale200k-mrr |
|
imix-2t1c-ethip6-ip6scale200k-mrr |
|
imix-4t2c-ethip6-ip6scale200k-mrr |
|
imix-8t4c-ethip6-ip6scale200k-mrr | timeout, not up [u’TenGigabitEthernet18/0/2’] |
10ge2p1x710-ethip6-ip6scale20k-mrr¶
Raw results IPv6 routing test cases
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv6 for IPv6 routing.
- [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv6 routing and 2x10k static IPv6 /64 route entries. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel.
- [Ver] TG verification: In MaxReceivedRate tests TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv6 header withq IP and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv6 destination address) field is applied to both streams.
- [Ref] Applicable standard specifications: RFC2544.
Name | Status |
---|---|
78b-2t1c-ethip6-ip6scale20k-mrr |
|
78b-4t2c-ethip6-ip6scale20k-mrr |
|
78b-8t4c-ethip6-ip6scale20k-mrr |
|
1518b-2t1c-ethip6-ip6scale20k-mrr |
|
1518b-4t2c-ethip6-ip6scale20k-mrr | timeout, not up [u’TenGigabitEthernet18/0/3’] |
1518b-8t4c-ethip6-ip6scale20k-mrr |
|
9000b-2t1c-ethip6-ip6scale20k-mrr |
|
9000b-4t2c-ethip6-ip6scale20k-mrr |
|
9000b-8t4c-ethip6-ip6scale20k-mrr |
|
imix-2t1c-ethip6-ip6scale20k-mrr |
|
imix-4t2c-ethip6-ip6scale20k-mrr |
|
imix-8t4c-ethip6-ip6scale20k-mrr |
|
10ge2p1x710-ethip6-ip6scale2m-mrr¶
Raw results IPv6 routing test cases
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv6 for IPv6 routing.
- [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv6 routing and 2x1M static IPv6 /64 route entries. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel.
- [Ver] TG verification: In MaxReceivedRate tests TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 1M flows per flow-group) with all packets containing Ethernet header, IPv6 header withq IP and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv6 destination address) field is applied to both streams.
- [Ref] Applicable standard specifications: RFC2544.
Name | Status |
---|---|
78b-2t1c-ethip6-ip6scale2m-mrr |
|
78b-4t2c-ethip6-ip6scale2m-mrr |
|
78b-8t4c-ethip6-ip6scale2m-mrr |
|
1518b-2t1c-ethip6-ip6scale2m-mrr |
|
1518b-4t2c-ethip6-ip6scale2m-mrr |
|
1518b-8t4c-ethip6-ip6scale2m-mrr | timeout, not up [u’TenGigabitEthernet18/0/3’] |
9000b-2t1c-ethip6-ip6scale2m-mrr | timeout, not up [u’TenGigabitEthernet18/0/2’, u’TenGigabitEthernet18/0/3’] |
9000b-4t2c-ethip6-ip6scale2m-mrr | timeout, not up [u’TenGigabitEthernet18/0/3’] |
9000b-8t4c-ethip6-ip6scale2m-mrr |
|
imix-2t1c-ethip6-ip6scale2m-mrr |
|
imix-4t2c-ethip6-ip6scale2m-mrr |
|
imix-8t4c-ethip6-ip6scale2m-mrr | timeout, not up [u’TenGigabitEthernet18/0/3’] |
l2¶
10ge2p1x710-dot1q-l2bdbasemaclrn-mrr¶
Raw results L2BD test cases with 802.1q test cases
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv4 for L2 switching of IPv4. 802.1q tagging is applied on link between DUT1 and DUT2.
- [Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 bridge domain and MAC learning enabled. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel.
- [Ver] TG verification: In MaxReceivedRate tests TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 254 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- [Ref] Applicable standard specifications: RFC2544.
Name | Status |
---|---|
64b-2t1c-dot1q-l2bdbasemaclrn-mrr | timeout, not up [u’TenGigabitEthernet18/0/2’, u’TenGigabitEthernet18/0/3’] |
64b-4t2c-dot1q-l2bdbasemaclrn-mrr |
|
64b-8t4c-dot1q-l2bdbasemaclrn-mrr | timeout, not up [u’TenGigabitEthernet18/0/3’] |
1518b-2t1c-dot1q-l2bdbasemaclrn-mrr |
|
1518b-4t2c-dot1q-l2bdbasemaclrn-mrr |
|
1518b-8t4c-dot1q-l2bdbasemaclrn-mrr |
|
9000b-2t1c-dot1q-l2bdbasemaclrn-mrr |
|
9000b-4t2c-dot1q-l2bdbasemaclrn-mrr |
|
9000b-8t4c-dot1q-l2bdbasemaclrn-mrr | timeout, not up [u’TenGigabitEthernet18/0/2’] |
imix-2t1c-dot1q-l2bdbasemaclrn-mrr |
|
imix-4t2c-dot1q-l2bdbasemaclrn-mrr |
|
imix-8t4c-dot1q-l2bdbasemaclrn-mrr | timeout, not up [u’TenGigabitEthernet18/0/3’] |
10ge2p1x710-dot1q-l2xcbase-mrr¶
Raw results L2XC with 802.1q test cases
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv4 for L2 cross connect. 802.1q tagging is applied on link between DUT1 and DUT2.
- [Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 cross- connect. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel.
- [Ver] TG verification: In MaxReceivedRate tests TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- [Ref] Applicable standard specifications: RFC2544.
Name | Status |
---|---|
64b-2t1c-dot1q-l2xcbase-mrr | timeout, not up [u’TenGigabitEthernet18/0/0’] |
64b-4t2c-dot1q-l2xcbase-mrr |
|
64b-8t4c-dot1q-l2xcbase-mrr |
|
1518b-2t1c-dot1q-l2xcbase-mrr |
|
1518b-4t2c-dot1q-l2xcbase-mrr |
|
1518b-8t4c-dot1q-l2xcbase-mrr | timeout, not up [u’TenGigabitEthernet18/0/3’] |
9000b-2t1c-dot1q-l2xcbase-mrr |
|
9000b-4t2c-dot1q-l2xcbase-mrr |
|
9000b-8t4c-dot1q-l2xcbase-mrr | timeout, not up [u’TenGigabitEthernet18/0/3’] |
imix-2t1c-dot1q-l2xcbase-mrr |
|
imix-4t2c-dot1q-l2xcbase-mrr |
|
imix-8t4c-dot1q-l2xcbase-mrr | timeout, not up [u’TenGigabitEthernet18/0/3’] |
10ge2p1x710-eth-l2bdbasemaclrn-iacl1sf-10kflows-mrr¶
Raw results L2BD test cases with ACL
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
- [Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with 2p10GE NIC X710 by Intel.
- [Ver] TG verification: In MaxReceivedRate tests TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- [Ref] Applicable standard specifications: RFC2544.
Name | Status |
---|---|
64b-2t1c-eth-l2bdbasemaclrn-iacl1sf-10kflows-mrr | timeout, not up [u’TenGigabitEthernet18/0/2’] |
64b-4t2c-eth-l2bdbasemaclrn-iacl1sf-10kflows-mrr | timeout, not up [u’TenGigabitEthernet18/0/2’] |
64b-8t4c-eth-l2bdbasemaclrn-iacl1sf-10kflows-mrr |
|
1518b-2t1c-eth-l2bdbasemaclrn-iacl1sf-10kflows-mrr |
|
1518b-4t2c-eth-l2bdbasemaclrn-iacl1sf-10kflows-mrr | timeout, not up [u’TenGigabitEthernet18/0/3’] |
1518b-8t4c-eth-l2bdbasemaclrn-iacl1sf-10kflows-mrr |
|
9000b-2t1c-eth-l2bdbasemaclrn-iacl1sf-10kflows-mrr |
|
9000b-4t2c-eth-l2bdbasemaclrn-iacl1sf-10kflows-mrr |
|
9000b-8t4c-eth-l2bdbasemaclrn-iacl1sf-10kflows-mrr | timeout, not up [u’TenGigabitEthernet18/0/3’] |
imix-2t1c-eth-l2bdbasemaclrn-iacl1sf-10kflows-mrr |
|
imix-4t2c-eth-l2bdbasemaclrn-iacl1sf-10kflows-mrr |
|
imix-8t4c-eth-l2bdbasemaclrn-iacl1sf-10kflows-mrr |
|
10ge2p1x710-eth-l2bdbasemaclrn-iacl1sl-10kflows-mrr¶
Raw results L2BD test cases with ACL
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
- [Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with 2p10GE NIC X710 by Intel.
- [Ver] TG verification: In MaxReceivedRate tests TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- [Ref] Applicable standard specifications: RFC2544.
Name | Status |
---|---|
64b-2t1c-eth-l2bdbasemaclrn-iacl1sl-10kflows-mrr |
|
64b-4t2c-eth-l2bdbasemaclrn-iacl1sl-10kflows-mrr |
|
64b-8t4c-eth-l2bdbasemaclrn-iacl1sl-10kflows-mrr |
|
1518b-2t1c-eth-l2bdbasemaclrn-iacl1sl-10kflows-mrr |
|
1518b-4t2c-eth-l2bdbasemaclrn-iacl1sl-10kflows-mrr |
|
1518b-8t4c-eth-l2bdbasemaclrn-iacl1sl-10kflows-mrr | timeout, not up [u’TenGigabitEthernet18/0/2’] |
9000b-2t1c-eth-l2bdbasemaclrn-iacl1sl-10kflows-mrr |
|
9000b-4t2c-eth-l2bdbasemaclrn-iacl1sl-10kflows-mrr | timeout, not up [u’TenGigabitEthernet18/0/3’] |
9000b-8t4c-eth-l2bdbasemaclrn-iacl1sl-10kflows-mrr |
|
imix-2t1c-eth-l2bdbasemaclrn-iacl1sl-10kflows-mrr |
|
imix-4t2c-eth-l2bdbasemaclrn-iacl1sl-10kflows-mrr | timeout, not up [u’TenGigabitEthernet18/0/3’] |
imix-8t4c-eth-l2bdbasemaclrn-iacl1sl-10kflows-mrr | timeout, not up [u’TenGigabitEthernet18/0/0’] |
10ge2p1x710-eth-l2bdbasemaclrn-iacl50sf-10kflows-mrr¶
Raw results L2BD test cases with ACL
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
- [Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with 2p10GE NIC X710 by Intel.
- [Ver] TG verification: In MaxReceivedRate tests TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- [Ref] Applicable standard specifications: RFC2544.
Name | Status |
---|---|
64b-2t1c-eth-l2bdbasemaclrn-iacl50sf-10kflows-mrr |
|
64b-4t2c-eth-l2bdbasemaclrn-iacl50sf-10kflows-mrr |
|
64b-8t4c-eth-l2bdbasemaclrn-iacl50sf-10kflows-mrr |
|
1518b-2t1c-eth-l2bdbasemaclrn-iacl50sf-10kflows-mrr |
|
1518b-4t2c-eth-l2bdbasemaclrn-iacl50sf-10kflows-mrr |
|
1518b-8t4c-eth-l2bdbasemaclrn-iacl50sf-10kflows-mrr | timeout, not up [u’TenGigabitEthernet18/0/3’] |
9000b-2t1c-eth-l2bdbasemaclrn-iacl50sf-10kflows-mrr |
|
9000b-4t2c-eth-l2bdbasemaclrn-iacl50sf-10kflows-mrr | timeout, not up [u’TenGigabitEthernet18/0/3’] |
9000b-8t4c-eth-l2bdbasemaclrn-iacl50sf-10kflows-mrr |
|
imix-2t1c-eth-l2bdbasemaclrn-iacl50sf-10kflows-mrr |
|
imix-4t2c-eth-l2bdbasemaclrn-iacl50sf-10kflows-mrr |
|
imix-8t4c-eth-l2bdbasemaclrn-iacl50sf-10kflows-mrr | timeout, not up [u’TenGigabitEthernet18/0/2’] |
10ge2p1x710-eth-l2bdbasemaclrn-iacl50sl-10kflows-mrr¶
Raw results L2BD test cases with ACL
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
- [Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with 2p10GE NIC X710 by Intel.
- [Ver] TG verification: In MaxReceivedRate tests TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- [Ref] Applicable standard specifications: RFC2544.
Name | Status |
---|---|
64b-2t1c-eth-l2bdbasemaclrn-iacl50sl-10kflows-mrr | timeout, not up [u’TenGigabitEthernet18/0/0’] |
64b-4t2c-eth-l2bdbasemaclrn-iacl50sl-10kflows-mrr |
|
64b-8t4c-eth-l2bdbasemaclrn-iacl50sl-10kflows-mrr | timeout, not up [u’TenGigabitEthernet18/0/3’] |
1518b-2t1c-eth-l2bdbasemaclrn-iacl50sl-10kflows-mrr |
|
1518b-4t2c-eth-l2bdbasemaclrn-iacl50sl-10kflows-mrr |
|
1518b-8t4c-eth-l2bdbasemaclrn-iacl50sl-10kflows-mrr | timeout, not up [u’TenGigabitEthernet18/0/3’] |
9000b-2t1c-eth-l2bdbasemaclrn-iacl50sl-10kflows-mrr | timeout, not up [u’TenGigabitEthernet18/0/2’] |
9000b-4t2c-eth-l2bdbasemaclrn-iacl50sl-10kflows-mrr |
|
9000b-8t4c-eth-l2bdbasemaclrn-iacl50sl-10kflows-mrr |
|
imix-2t1c-eth-l2bdbasemaclrn-iacl50sl-10kflows-mrr |
|
imix-4t2c-eth-l2bdbasemaclrn-iacl50sl-10kflows-mrr | timeout, not up [u’TenGigabitEthernet18/0/3’] |
imix-8t4c-eth-l2bdbasemaclrn-iacl50sl-10kflows-mrr |
|
10ge2p1x710-eth-l2bdbasemaclrn-mrr¶
Raw results L2BD test cases
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv4 for L2 switching of IPv4.
- [Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 bridge- domain and MAC learning enabled. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel.
- [Ver] TG verification: In MaxReceivedRate tests TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- [Ref] Applicable standard specifications: RFC2544.
Name | Status |
---|---|
64b-2t1c-eth-l2bdbasemaclrn-mrr |
|
64b-4t2c-eth-l2bdbasemaclrn-mrr |
|
64b-8t4c-eth-l2bdbasemaclrn-mrr |
|
1518b-2t1c-eth-l2bdbasemaclrn-mrr | timeout, not up [u’TenGigabitEthernet18/0/0’] |
1518b-4t2c-eth-l2bdbasemaclrn-mrr |
|
1518b-8t4c-eth-l2bdbasemaclrn-mrr |
|
9000b-2t1c-eth-l2bdbasemaclrn-mrr |
|
9000b-4t2c-eth-l2bdbasemaclrn-mrr |
|
9000b-8t4c-eth-l2bdbasemaclrn-mrr | timeout, not up [u’TenGigabitEthernet18/0/3’] |
imix-2t1c-eth-l2bdbasemaclrn-mrr | timeout, not up [u’TenGigabitEthernet18/0/3’] |
imix-4t2c-eth-l2bdbasemaclrn-mrr | timeout, not up [u’TenGigabitEthernet18/0/0’] |
imix-8t4c-eth-l2bdbasemaclrn-mrr |
|
10ge2p1x710-eth-l2bdscale100kmaclrn-mrr¶
Raw results for L2BD test cases
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv4 for L2 switching of IPv4.
- [Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 bridge- domain and MAC learning enabled. DUT1 and DUT2 tested with 2p10GE NI X710 by Intel.
- [Ver] TG verification: In MaxReceivedRate tests TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 50k flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses ranges are incremented as follows: port01_src ca:fe:00:00:00:00 - port01_src ca:fe:00:00:c3:4f, port01_dst fa:ce:00:00:00:00 - port01_dst fa:ce:00:00:c3:4f, port02_src fa:ce:00:00:00:00 - port02_src fa:ce:00:00:c3:4f, port02_dst ca:fe:00:00:00:00 - port02_dst ca:fe:00:00:c3:4f,
- [Ref] Applicable standard specifications: RFC2544.
Name | Status |
---|---|
64b-2t1c-eth-l2bdscale100kmaclrn-mrr |
|
64b-4t2c-eth-l2bdscale100kmaclrn-mrr |
|
64b-8t4c-eth-l2bdscale100kmaclrn-mrr | timeout, not up [u’TenGigabitEthernet18/0/2’, u’TenGigabitEthernet18/0/3’] |
1518b-2t1c-eth-l2bdscale100kmaclrn-mrr |
|
1518b-4t2c-eth-l2bdscale100kmaclrn-mrr |
|
1518b-8t4c-eth-l2bdscale100kmaclrn-mrr |
|
9000b-2t1c-eth-l2bdscale100kmaclrn-mrr |
|
9000b-4t2c-eth-l2bdscale100kmaclrn-mrr | timeout, not up [u’TenGigabitEthernet18/0/0’] |
9000b-8t4c-eth-l2bdscale100kmaclrn-mrr | timeout, not up [u’TenGigabitEthernet18/0/3’] |
imix-2t1c-eth-l2bdscale100kmaclrn-mrr |
|
imix-4t2c-eth-l2bdscale100kmaclrn-mrr | timeout, not up [u’TenGigabitEthernet18/0/0’] |
imix-8t4c-eth-l2bdscale100kmaclrn-mrr | timeout, not up [u’TenGigabitEthernet18/0/3’] |
10ge2p1x710-eth-l2bdscale10kmaclrn-mrr¶
Raw results for L2BD test cases
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv4 for L2 switching of IPv4.
- [Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 bridge- domain and MAC learning enabled. DUT1 and DUT2 tested with 2p10GE NI X710 by Intel.
- [Ver] TG verification: In MaxReceivedRate tests TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 5k flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses ranges are incremented as follows: port01_src ca:fe:00:00:00:00 - port01_src ca:fe:00:00:13:87, port01_dst fa:ce:00:00:00:00 - port01_dst fa:ce:00:00:13:87, port02_src fa:ce:00:00:00:00 - port02_src fa:ce:00:00:13:87, port02_dst ca:fe:00:00:00:00 - port02_dst ca:fe:00:00:13:87,
- [Ref] Applicable standard specifications: RFC2544.
Name | Status |
---|---|
64b-2t1c-eth-l2bdscale10kmaclrn-mrr | timeout, not up [u’TenGigabitEthernet18/0/3’] |
64b-4t2c-eth-l2bdscale10kmaclrn-mrr |
|
64b-8t4c-eth-l2bdscale10kmaclrn-mrr |
|
1518b-2t1c-eth-l2bdscale10kmaclrn-mrr | timeout, not up [u’TenGigabitEthernet18/0/2’] |
1518b-4t2c-eth-l2bdscale10kmaclrn-mrr | timeout, not up [u’TenGigabitEthernet18/0/3’] |
1518b-8t4c-eth-l2bdscale10kmaclrn-mrr |
|
9000b-2t1c-eth-l2bdscale10kmaclrn-mrr | timeout, not up [u’TenGigabitEthernet18/0/0’] |
9000b-4t2c-eth-l2bdscale10kmaclrn-mrr |
|
9000b-8t4c-eth-l2bdscale10kmaclrn-mrr | timeout, not up [u’TenGigabitEthernet18/0/3’] |
imix-2t1c-eth-l2bdscale10kmaclrn-mrr |
|
imix-4t2c-eth-l2bdscale10kmaclrn-mrr | timeout, not up [u’TenGigabitEthernet18/0/2’, u’TenGigabitEthernet18/0/3’] |
imix-8t4c-eth-l2bdscale10kmaclrn-mrr |
|
10ge2p1x710-eth-l2bdscale1mmaclrn-mrr¶
Raw results for L2BD test cases
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv4 for L2 switching of IPv4.
- [Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 bridge- domain and MAC learning enabled. DUT1 and DUT2 tested with 2p10GE NI X710 by Intel.
- [Ver] TG verification: In MaxReceivedRate tests TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 500k flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses ranges are incremented as follows: port01_src ca:fe:00:00:00:00 - port01_src ca:fe:00:07:a1:1f, port01_dst fa:ce:00:00:00:00 - port01_dst fa:ce:00:07:a1:1f, port02_src fa:ce:00:00:00:00 - port02_src fa:ce:00:07:a1:1f, port02_dst ca:fe:00:00:00:00 - port02_dst ca:fe:00:07:a1:1f,
- [Ref] Applicable standard specifications: RFC2544.
Name | Status |
---|---|
64b-2t1c-eth-l2bdscale1mmaclrn-mrr |
|
64b-4t2c-eth-l2bdscale1mmaclrn-mrr | timeout, not up [u’TenGigabitEthernet18/0/2’, u’TenGigabitEthernet18/0/3’] |
64b-8t4c-eth-l2bdscale1mmaclrn-mrr |
|
1518b-2t1c-eth-l2bdscale1mmaclrn-mrr | timeout, not up [u’TenGigabitEthernet18/0/0’] |
1518b-4t2c-eth-l2bdscale1mmaclrn-mrr |
|
1518b-8t4c-eth-l2bdscale1mmaclrn-mrr |
|
9000b-2t1c-eth-l2bdscale1mmaclrn-mrr |
|
9000b-4t2c-eth-l2bdscale1mmaclrn-mrr | timeout, not up [u’TenGigabitEthernet18/0/0’] |
9000b-8t4c-eth-l2bdscale1mmaclrn-mrr | timeout, not up [u’TenGigabitEthernet18/0/3’] |
imix-2t1c-eth-l2bdscale1mmaclrn-mrr |
|
imix-4t2c-eth-l2bdscale1mmaclrn-mrr | timeout, not up [u’TenGigabitEthernet18/0/3’] |
imix-8t4c-eth-l2bdscale1mmaclrn-mrr | timeout, not up [u’TenGigabitEthernet18/0/3’] |
10ge2p1x710-eth-l2patch-mrr¶
Raw results L2patch test cases
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv4 for L2 patch.
- [Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 patch DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel.
- [Ver] TG verification: In MaxReceivedRate tests TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 254 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
Name | Status |
---|---|
64b-2t1c-eth-l2patch-mrr | timeout, not up [u’TenGigabitEthernet18/0/3’] |
64b-4t2c-eth-l2patch-mrr | timeout, not up [u’TenGigabitEthernet18/0/3’] |
64b-8t4c-eth-l2patch-mrr |
|
1518b-2t1c-eth-l2patch-mrr |
|
1518b-4t2c-eth-l2patch-mrr |
|
1518b-8t4c-eth-l2patch-mrr | timeout, not up [u’TenGigabitEthernet18/0/3’] |
9000b-2t1c-eth-l2patch-mrr |
|
9000b-4t2c-eth-l2patch-mrr |
|
9000b-8t4c-eth-l2patch-mrr | timeout, not up [u’TenGigabitEthernet18/0/3’] |
imix-2t1c-eth-l2patch-mrr |
|
imix-4t2c-eth-l2patch-mrr |
|
imix-8t4c-eth-l2patch-mrr | timeout, not up [u’TenGigabitEthernet18/0/2’] |
10ge2p1x710-eth-l2xcbase-mrr¶
Raw results L2XC test cases
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv4 for L2 cross connect.
- [Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 cross- connect. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel.
- [Ver] TG verification: In MaxReceivedRate tests TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- [Ref] Applicable standard specifications: RFC2544.
Name | Status |
---|---|
64b-2t1c-eth-l2xcbase-mrr |
|
64b-4t2c-eth-l2xcbase-mrr | timeout, not up [u’TenGigabitEthernet18/0/3’] |
64b-8t4c-eth-l2xcbase-mrr |
|
1518b-2t1c-eth-l2xcbase-mrr |
|
1518b-4t2c-eth-l2xcbase-mrr | timeout, not up [u’TenGigabitEthernet18/0/0’] |
1518b-8t4c-eth-l2xcbase-mrr | timeout, not up [u’TenGigabitEthernet18/0/3’] |
9000b-2t1c-eth-l2xcbase-mrr | timeout, not up [u’TenGigabitEthernet18/0/2’] |
9000b-4t2c-eth-l2xcbase-mrr | timeout, not up [u’TenGigabitEthernet18/0/3’] |
9000b-8t4c-eth-l2xcbase-mrr |
|
imix-2t1c-eth-l2xcbase-mrr |
|
imix-4t2c-eth-l2xcbase-mrr | timeout, not up [u’TenGigabitEthernet18/0/0’] |
imix-8t4c-eth-l2xcbase-mrr | timeout, not up [u’TenGigabitEthernet18/0/3’] |
25ge2p1xxv710-eth-l2patch-mrr¶
Raw results L2patch test cases
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv4 for L2 patch.
- [Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 patch DUT1 and DUT2 tested with 2p25GE NIC XXV710 by Intel.
- [Ver] TG verification: In MaxReceivedRate tests TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 254 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
Name | Status |
---|---|
64b-2t1c-eth-l2patch-mrr |
|
64b-4t2c-eth-l2patch-mrr |
|
64b-8t4c-eth-l2patch-mrr |
|
1518b-2t1c-eth-l2patch-mrr |
|
1518b-4t2c-eth-l2patch-mrr |
|
1518b-8t4c-eth-l2patch-mrr |
|
9000b-2t1c-eth-l2patch-mrr |
|
9000b-4t2c-eth-l2patch-mrr |
|
9000b-8t4c-eth-l2patch-mrr |
|
imix-2t1c-eth-l2patch-mrr |
|
imix-4t2c-eth-l2patch-mrr |
|
imix-8t4c-eth-l2patch-mrr |
|