l2bd¶

eth2p-avf-dot1qip4-l2bdbasemaclrn-dev¶

IPv4 routing with IEEE 802.1Q test cases

[Top] Network Topologies: TG-DUT1-TG 2-node circular topology with single links between nodes.

[Enc] Packet Encapsulations: Eth-IPv4 for IPv4 routing. IEEE 802.1Q tagging is applied on links between TG-DUT1.

[Cfg] DUT configuration: DUT1 is configured with IPv4 routing and two static IPv4 /30 route entries. DUT1 is tested with virtual.

[Ver] TG verification: Test IPv4 packets are sent in one direction by TG on link to DUT1; on receive TG verifies packets for correctness and drops as applicable.

[Ref] Applicable standard specifications: IEEE 802.1q.

 Test Name

 VPP API Test Commands History - Commands Used Per Test Case

 68b-avf- 
 dot1qip4-l2bdbasemaclrn-dev

 DUT1:  
 cli_inband(cmd=’show log’) 
 show_version() 
 sw_interface_dump(name_filter=’’,name_filter_valid=0) 
 cli_inband(cmd=’trace add dpdk-input 50’) 
 cli_inband(cmd=’trace add vhost-user-input 50’) 
 cli_inband(cmd=’trace add memif-input 50’) 
 cli_inband(cmd=’trace add avf-input 50’) 
 avf_create(rxq_size=0,txq_size=0,enable_elog=0,pci_addr=171638784,rxq_num=1) 
 sw_interface_dump(name_filter=’’,name_filter_valid=0) 
 sw_interface_dump(name_filter=’’,name_filter_valid=0) 
 avf_create(rxq_size=0,txq_size=0,enable_elog=0,pci_addr=708509696,rxq_num=1) 
 sw_interface_dump(name_filter=’’,name_filter_valid=0) 
 sw_interface_dump(name_filter=’’,name_filter_valid=0) 
 sw_interface_set_flags(sw_if_index=1,admin_up_down=1) 
 sw_interface_set_flags(sw_if_index=2,admin_up_down=1) 
 hw_interface_set_mtu(sw_if_index=1,mtu=9200) 
 hw_interface_set_mtu(sw_if_index=2,mtu=9200) 
 sw_interface_dump(name_filter=’’,name_filter_valid=0) 
 sw_interface_set_flags(sw_if_index=1,admin_up_down=1) 
 sw_interface_set_flags(sw_if_index=2,admin_up_down=1) 
 hw_interface_set_mtu(sw_if_index=1,mtu=9200) 
 hw_interface_set_mtu(sw_if_index=2,mtu=9200) 
 sw_interface_dump(name_filter=’’,name_filter_valid=0) 
 create_vlan_subif(vlan_id=1300,sw_if_index=1) 
 sw_interface_dump(name_filter=’’,name_filter_valid=0) 
 sw_interface_dump(name_filter=’’,name_filter_valid=0) 
 create_vlan_subif(vlan_id=1301,sw_if_index=2) 
 sw_interface_dump(name_filter=’’,name_filter_valid=0) 
 sw_interface_dump(name_filter=’’,name_filter_valid=0) 
 sw_interface_set_flags(sw_if_index=3,admin_up_down=1) 
 sw_interface_set_flags(sw_if_index=4,admin_up_down=1) 
 l2_interface_vlan_tag_rewrite(vtr_op=3,tag2=0,push_dot1q=1,tag1=0,sw_if_index=3) 
 l2_interface_vlan_tag_rewrite(vtr_op=3,tag2=0,push_dot1q=1,tag1=0,sw_if_index=4) 
 sw_interface_set_l2_bridge(rx_sw_if_index=3,enable=1,shg=0,port_type=0,bd_id=1) 
 sw_interface_set_l2_bridge(rx_sw_if_index=4,enable=1,shg=0,port_type=0,bd_id=1)

eth2p-ethicmpv4-l2bdbasemaclrn-dev¶

L2 bridge-domain test cases

[Top] Network Topologies: TG-DUT1-TG 2-node circular topology with single links between nodes.

[Enc] Packet Encapsulations: Eth-IPv4-ICMPv4 for L2 switching of IPv4. Both apply to all links.

[Cfg] DUT configuration: DUT1 is configured with L2 bridge-domain switching.

[Ver] TG verification: Test ICMPv4 Echo Request packets are sent in both directions by TG on links to DUT1; on receive TG verifies packets for correctness and their IPv4 src-addr, dst-addr and MAC addresses.

[Ref] Applicable standard specifications: RFC792

 Test Name

 VPP API Test Commands History - Commands Used Per Test Case

 64b-ethicmpv4- 
 l2bdbasemaclrn-dev

 DUT1:  
 cli_inband(cmd=’show log’) 
 show_version() 
 sw_interface_dump(name_filter=’’,name_filter_valid=0) 
 cli_inband(cmd=’trace add dpdk-input 50’) 
 cli_inband(cmd=’trace add vhost-user-input 50’) 
 cli_inband(cmd=’trace add memif-input 50’) 
 cli_inband(cmd=’trace add avf-input 50’) 
 sw_interface_set_flags(sw_if_index=1,admin_up_down=1) 
 sw_interface_set_flags(sw_if_index=2,admin_up_down=1) 
 hw_interface_set_mtu(sw_if_index=1,mtu=9200) 
 hw_interface_set_mtu(sw_if_index=2,mtu=9200) 
 sw_interface_dump(name_filter=’’,name_filter_valid=0) 
 sw_interface_dump(name_filter=’’,name_filter_valid=0) 
 sw_interface_dump(name_filter=’’,name_filter_valid=0) 
 sw_interface_set_l2_bridge(rx_sw_if_index=1,enable=1,shg=0,port_type=0,bd_id=1) 
 sw_interface_set_l2_bridge(rx_sw_if_index=2,enable=1,shg=0,port_type=0,bd_id=1)