Create Interfaces Commands

This section contains those interface commands that are associated to creating an interface:

Note

For a complete list of CLI Debug commands refer to the Debug CLI section of the Source Code Documents .

Create Host-Interface

create host-interface name <*ifname*> [*hw-addr <*mac-addr*>]

Description

Create a host interface that will attach to a linux AF_PACKET interface, one side of a veth pair. The veth pair must already exist. Once created, a new host interface will exist in VPP with the name ‘host-<ifname>’, where ‘<ifname>’ is the name of the specified veth pair. Use the show interface command to display host interface details.

This command has the following optional parameters:

hw-addr <mac-addr> - Optional ethernet address, can be in either X:X:X:X:X:X unix or X.X.X cisco format

Example Usage

Example of how to create a host interface tied to one side of an existing linux veth pair named vpp1:

vpp# create host-interface name vpp1

host-vpp1

Once the host interface is created, enable the interface using:

vpp# set interface state host-vpp1 up

Declaration and Implementation

Declaration: af_packet_create_command (src/vnet/devices/af_packet/cli.c line 133)

Implementation: af_packet_create_command_fn

Create Interface Memif

create interface memif [id <*id*>] [socket-id <*socket-id*>] [ring-size <*size*>] [buffer-size <*size*>] [hw-addr <*mac-address*>] <master|slave> [rx-queues <*number*>] [tx-queues <*number*>] [mode ip] [secret <*string*>]

Declaration and Implementation

Declaration: memif_create_command (src/plugins/memif/cli.c line 258)

Implementation: memif_create_command_fn

Create Loopback Interface

Create a loopback interface. Optionally, a MAC Address can be provided. If not provided, de:ad:00:00:00:<loopId> will be used.

create loopback interface [mac <*mac-addr*>] [instance <*instance*>]

Example Usage

The following two command syntaxes are equivalent:

vpp# loopback create-interface [mac <*mac-addr*>] [instance <*instance*>]

vpp# create loopback interface [mac <*mac-addr*>] [instance <*instance*>]

Example of how to create a loopback interface:

vpp# create loopback interface

Declaration and Implementation

Declaration: create_loopback_interface_command (src/vnet/ethernet/interface.c line 879)

Implementation: create_simulated_ethernet_interfaces

Create Sub-Interfaces

This command is used to add VLAN IDs to interfaces, also known as subinterfaces. The primary input to this command is the interface and subId (subinterface Id) parameters. If no additional VLAN ID is provide, the VLAN ID is assumed to be the subId. The VLAN ID and subId can be different, but this is not recommended.

This command has several variations:

  • create sub-interfaces <interface> <subId> - Create a subinterface to process packets with a given 802.1q VLAN ID (same value as the subId).

  • create sub-interfaces <interface> <subId> default - Adding the default parameter indicates that packets with VLAN IDs that do not match any other subinterfaces should be sent to this subinterface.

  • create sub-interfaces <interface> <subId> untagged - Adding the untagged parameter indicates that packets no VLAN IDs should be sent to this subinterface.

  • create sub-interfaces <interface> <subId>-<subId> - Create a range of subinterfaces to handle a range of VLAN IDs.

  • create sub-interfaces <interface> <subId> dot1q|dot1ad <vlanId>|any [exact-match] - Use this command to explicitly specify the outer VLAN ID, or to make the VLAN ID different from the subId.

  • create sub-interfaces <interface> <subId> dot1q|dot1ad <vlanId>|any inner-dot1q <vlanId>|any [exact-match] - Use this command to specify the outer VLAN ID and the inner VLAN ID.

When dot1q or dot1ad is explicitly entered, subinterfaces can be configured as either exact-match or non-exact match. Non-exact match is the CLI default. If exact-match is specified, packets must have the same number of VLAN tags as the configuration. For non-exact-match, packets must at least that number of tags. L3 (routed) interfaces must be configured as exact-match. L2 interfaces are typically configured as non-exact-match. If dot1q or dot1ad is NOT entered, then the default behavior is exact-match.

Use the show interface command to display all subinterfaces.

Summary/Usage

create sub-interfaces <interface> {<subId> [default|untagged]} | {<subId>-<subId>} | {<subId> dot1q|dot1ad <vlanId>|any [inner-dot1q <vlanId>|any] [exact-match]}

Example Usage

Example of how to create a VLAN subinterface 11 to process packets on 802.1q VLAN ID 11:

vpp# create sub-interfaces GigabitEthernet2/0/0 11

The previous example is shorthand and is equivalent to:

vpp# create sub-interfaces GigabitEthernet2/0/0 11 dot1q 11 exact-match

Example of how to create a subinterface number that is different from the VLAN ID:

vpp# create sub-interfaces GigabitEthernet2/0/0 11 dot1q 100

Examples of how to create q-in-q and q-in-any subinterfaces:

vpp# create sub-interfaces GigabitEthernet2/0/0 11 dot1q 100 inner-dot1q 200
vpp# create sub-interfaces GigabitEthernet2/0/0 12 dot1q 100 inner-dot1q any

Examples of how to create dot1ad interfaces:

vpp# create sub-interfaces GigabitEthernet2/0/0 11 dot1ad 11
vpp# create sub-interfaces GigabitEthernet2/0/0 12 dot1ad 100 inner-dot1q 200

Examples of exact-match versus non-exact match. A packet with outer VLAN 100 and inner VLAN 200 would match this interface, because the default is non-exact match:

vpp# create sub-interfaces GigabitEthernet2/0/0 5 dot1q 100

However, the same packet would NOT match this interface because exact-match is specified and only one VLAN is configured, but packet contains two VLANs:

vpp# create sub-interfaces GigabitEthernet2/0/0 5 dot1q 100 exact-match

Example of how to created a subinterface to process untagged packets:

vpp# create sub-interfaces GigabitEthernet2/0/0 5 untagged

Example of how to created a subinterface to process any packet with a VLAN ID that does not match any other subinterface:

vpp# create sub-interfaces GigabitEthernet2/0/0 7 default

When subinterfaces are created, they are in the down state. Example of how to enable a newly created subinterface:

vpp# set interface GigabitEthernet2/0/0.7 up