FD.io VPP  v20.05.1-5-g09f167997
Vector Packet Processing
Intel AVF device plugin for VPP

Overview

This plugins provides native device support for intel Adaptive Virtual Function (AVF). AVF is driver specification for current and future Intel Virtual Function devices. AVF defines communication channel between Physical Functions (PF) and VF. In essence, today this driver can be used only with Intel XL710 / X710 / XXV710 adapters.

Prerequisites

  • Driver requires newer i40e PF linux driver to be installed on the system, which supports virtualchnl interface. This code is tested with i40e driver version 2.4.6.

Driver requires MSI-X interrupt support, which is not supported by uio_pci_generic driver, so vfio-pci needs to be used. On systems without IOMMU vfio driver can still be used with recent kernels which support no-iommu mode.

Known issues

This driver is still in experimental phase, however it shows very good performance numbers.

Usage

System setup

  1. load VFIO driver
    sudo modprobe vfio-pci
  2. (systems without IOMMU only) enable unsafe NOIOMMU mode
    echo Y | sudo tee /sys/module/vfio/parameters/enable_unsafe_noiommu_mode
  3. Create and bind SR-IOV virtual function(s)

Following script creates VF, assigns MAC address and binds VF to vfio-pci

#!/bin/bash
if [ $USER != "root" ] ; then
echo "Restarting script with sudo..."
sudo $0 ${*}
exit
fi
setup () {
cd /sys/bus/pci/devices/${1}
driver=$(basename $(readlink driver))
if [ "${driver}" != "i40e" ]; then
echo ${1} | tee driver/unbind
echo ${1} | tee /sys/bus/pci/drivers/i40e/bind
fi
ifname=$(basename net/*)
echo 0 | tee sriov_numvfs > /dev/null
echo 1 | tee sriov_numvfs > /dev/null
ip link set dev ${ifname} vf 0 mac ${2}
ip link show dev ${ifname}
vf=$(basename $(readlink virtfn0))
echo ${vf} | tee virtfn0/driver/unbind
echo vfio-pci | tee virtfn0/driver_override
echo ${vf} | sudo tee /sys/bus/pci/drivers/vfio-pci/bind
echo | tee virtfn0/driver_override
}
# Setup one VF on PF 0000:3b:00.0 and assign MAC address
setup 0000:3b:00.0 00:11:22:33:44:00
# Setup one VF on PF 0000:3b:00.1 and assign MAC address
setup 0000:3b:00.1 00:11:22:33:44:01

Promisc mode

In cases when interface is used in the L2 mode or promisc mode is needed for some other reason, trust needs to be set to "on" using the linux "ip link" utility.

ip link set dev <PF inteface name> vf <VF id> trust on

L2 spoofing check

By default Virtual Function is not allowed to send ethernet frames which have source MAC address different than address assigned to the VF. In some cases it is expected that VPP will send such frames (e.g. L2 bridging, bonding, l2 cross-connect) and in such cases spoof chack needs to be turned off by issuing following command:

ip link set dev <PF inteface name> vf <VF id> spoofchk off

Interface Creation

Interfaces can be dynamically created by using following CLI:

create interface avf 0000:3b:02.0
set int state avf-0/3b/2/0 up

Interface Deletion

Interface can be deleted with following CLI:

delete interface avf <interface name>

Interface Statistics

Interface statistics can be displayed with sh hardware-interface <if-name> command.