2n-tx2-xl710

2n1l-40ge2p1xl710-ethip4ipsec10000tnlsw-ip4base-int-aes128cbc-hmac512sha-udir-mrr

RFC2544: Pkt throughput IPv4 IPsec tunnel mode.

  • [Top] Network Topologies: TG-DUT1-TG 2-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 on TG-DUT1, Eth-IPv4-IPSec on DUT1-TG.

  • [Cfg] DUT configuration: DUT1 is configured with multiple IPsec tunnels between it and TG. DUT gets IPv4 traffic from TG, encrypts it and sends back to TG.

  • [Ver] TG vefication: In MaxReceivedRate tests TG sends traffic at line rate and reports total received packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains one L3 flow-groups (number of flows per flow-group equals to number of IPSec tunnels) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv4 destination address) field is applied to the stream.

  • [Ref] Applicable standard specifications: RFC4303 and RFC2544.

 Test Name 

 Maximum Receive Rate trial [Mpps] 

 1518b-1t1c-ethip4ipsec10000tnlsw-ip4base- 
int-aes128cbc-hmac512sha-udir-mrr

 [0.11, 0.11, 0.11, 0.11, 0.11, 0.11, 0.11, 0.11, 0.11, 0.11] 

 1518b-2t2c-ethip4ipsec10000tnlsw-ip4base- 
int-aes128cbc-hmac512sha-udir-mrr

 [0.21, 0.21, 0.21, 0.21, 0.21, 0.21, 0.21, 0.21, 0.21, 0.21] 

 1518b-4t4c-ethip4ipsec10000tnlsw-ip4base- 
int-aes128cbc-hmac512sha-udir-mrr

 [0.41, 0.41, 0.41, 0.41, 0.41, 0.41, 0.41, 0.41, 0.41, 0.41] 

 imix-1t1c-ethip4ipsec10000tnlsw-ip4base- 
int-aes128cbc-hmac512sha-udir-mrr

 [0.24, 0.24, 0.24, 0.24, 0.24, 0.24, 0.24, 0.24, 0.24, 0.24] 

 imix-2t2c-ethip4ipsec10000tnlsw-ip4base- 
int-aes128cbc-hmac512sha-udir-mrr

 [0.48, 0.48, 0.48, 0.48, 0.48, 0.48, 0.48, 0.48, 0.48, 0.48] 

 imix-4t4c-ethip4ipsec10000tnlsw-ip4base- 
int-aes128cbc-hmac512sha-udir-mrr

 [0.92, 0.92, 0.92, 0.92, 0.92, 0.92, 0.92, 0.92, 0.92, 0.92] 

2n1l-40ge2p1xl710-ethip4ipsec10000tnlsw-ip4base-int-aes128gcm-udir-mrr

RFC2544: Pkt throughput IPv4 IPsec tunnel mode.

  • [Top] Network Topologies: TG-DUT1-TG 2-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 on TG-DUT1, Eth-IPv4-IPSec on DUT1-TG.

  • [Cfg] DUT configuration: DUT1 is configured with multiple IPsec tunnels between it and TG. DUT gets IPv4 traffic from TG, encrypts it and sends back to TG.

  • [Ver] TG vefication: In MaxReceivedRate tests TG sends traffic at line rate and reports total received packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains one L3 flow-groups (number of flows per flow-group equals to number of IPSec tunnels) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv4 destination address) field is applied to the stream.

  • [Ref] Applicable standard specifications: RFC4303 and RFC2544.

 Test Name 

 Maximum Receive Rate trial [Mpps] 

 1518b-1t1c-ethip4ipsec10000tnlsw-ip4base- 
int-aes128gcm-udir-mrr

 [0.50, 0.50, 0.50, 0.50, 0.50, 0.50, 0.50, 0.50, 0.50, 0.50] 

 1518b-2t2c-ethip4ipsec10000tnlsw-ip4base- 
int-aes128gcm-udir-mrr

 [1.00, 1.00, 1.00, 1.00, 1.00, 1.00, 1.00, 1.00, 1.00, 1.00] 

 1518b-4t4c-ethip4ipsec10000tnlsw-ip4base- 
int-aes128gcm-udir-mrr

 [1.79, 1.79, 1.79, 1.79, 1.78, 1.78, 1.77, 1.78, 1.78, 1.78] 

 imix-1t1c-ethip4ipsec10000tnlsw-ip4base- 
int-aes128gcm-udir-mrr

 [1.27, 1.28, 1.27, 1.27, 1.27, 1.27, 1.27, 1.27, 1.27, 1.27] 

 imix-2t2c-ethip4ipsec10000tnlsw-ip4base- 
int-aes128gcm-udir-mrr

 [2.54, 2.54, 2.54, 2.54, 2.54, 2.53, 2.53, 2.53, 2.53, 2.54] 

 imix-4t4c-ethip4ipsec10000tnlsw-ip4base- 
int-aes128gcm-udir-mrr

 [4.60, 4.59, 4.59, 4.59, 4.58, 4.58, 4.58, 4.58, 4.58, 4.58] 

2n1l-40ge2p1xl710-ethip4ipsec10000tnlsw-ip4base-int-aes256gcm-udir-mrr

RFC2544: Pkt throughput IPv4 IPsec tunnel mode.

  • [Top] Network Topologies: TG-DUT1-TG 2-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 on TG-DUT1, Eth-IPv4-IPSec on DUT1-TG.

  • [Cfg] DUT configuration: DUT1 is configured with multiple IPsec tunnels between it and TG. DUT gets IPv4 traffic from TG, encrypts it and sends back to TG.

  • [Ver] TG vefication: In MaxReceivedRate tests TG sends traffic at line rate and reports total received packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains one L3 flow-groups (number of flows per flow-group equals to number of IPSec tunnels) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv4 destination address) field is applied to the stream.

  • [Ref] Applicable standard specifications: RFC4303 and RFC2544.

 Test Name 

 Maximum Receive Rate trial [Mpps] 

 1518b-1t1c-ethip4ipsec10000tnlsw-ip4base- 
int-aes256gcm-udir-mrr

 [0.42, 0.42, 0.42, 0.42, 0.42, 0.42, 0.42, 0.42, 0.42, 0.42] 

 1518b-2t2c-ethip4ipsec10000tnlsw-ip4base- 
int-aes256gcm-udir-mrr

 [0.85, 0.85, 0.85, 0.85, 0.85, 0.85, 0.85, 0.85, 0.85, 0.85] 

 1518b-4t4c-ethip4ipsec10000tnlsw-ip4base- 
int-aes256gcm-udir-mrr

 [1.52, 1.53, 1.52, 1.52, 1.52, 1.52, 1.52, 1.52, 1.52, 1.51] 

 imix-1t1c-ethip4ipsec10000tnlsw-ip4base- 
int-aes256gcm-udir-mrr

 [1.14, 1.14, 1.14, 1.14, 1.14, 1.14, 1.13, 1.14, 1.13, 1.14] 

 imix-2t2c-ethip4ipsec10000tnlsw-ip4base- 
int-aes256gcm-udir-mrr

 [2.27, 2.27, 2.27, 2.27, 2.27, 2.25, 2.27, 2.27, 2.27, 2.26] 

 imix-4t4c-ethip4ipsec10000tnlsw-ip4base- 
int-aes256gcm-udir-mrr

 [4.09, 4.09, 4.09, 4.09, 4.09, 4.08, 4.08, 4.07, 4.07, 4.07] 

2n1l-40ge2p1xl710-ethip4ipsec1000spe-cache-ip4base-policy-outbound-nocrypto-mrr

RFC4301: SPD lookup performance

  • [Top] Network Topologies: TG-DUT1-TG 2-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 for IPv4 routing.

  • [Cfg] DUT configuration: DUT1 is configured with IPv4 routing, two static IPv4 /24 route entries, one SPD on each outbound interface in each direction and 1000 SPD entry(ies) in each SPD. Only outbound traffic is matched and only the last rule is the matching rule. SPD flow-cache for IPv4 outbound traffic is enabled. DUT1 is tested with Intel-XL710.

  • [Ver] TG vefication: In MaxReceivedRate tests TG sends traffic at line rate and reports total received packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. The DUT does SPD lookup with only the lowest priority rule matching the traffic. The action of the matching rule is BYPASS. No encryption or authentication is done.

  • [Ref] Applicable standard specifications: RFC4301 and RFC2544.

 Test Name 

 Maximum Receive Rate trial [Mpps] 

 64b-1t1c-ethip4ipsec1000spe-cache- 
ip4base-policy-outbound-nocrypto-mrr

 [4.38, 4.44, 4.40, 4.39, 4.42, 4.42, 4.41, 4.40, 4.41, 4.40] 

 64b-2t2c-ethip4ipsec1000spe-cache- 
ip4base-policy-outbound-nocrypto-mrr

 [8.97, 8.92, 8.90, 8.95, 8.90, 8.95, 8.93, 8.92, 8.94, 8.92] 

 64b-4t4c-ethip4ipsec1000spe-cache- 
ip4base-policy-outbound-nocrypto-mrr

 [15.82, 15.77, 15.79, 15.76, 15.72, 15.72, 15.75, 15.81, 15.80, 15.75] 

2n1l-40ge2p1xl710-ethip4ipsec1000spe-ip4base-policy-outbound-nocrypto-mrr

RFC4301: SPD lookup performance

  • [Top] Network Topologies: TG-DUT1-TG 2-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 for IPv4 routing.

  • [Cfg] DUT configuration: DUT1 is configured with IPv4 routing, two static IPv4 /24 route entries, one SPD on each outbound interface in each direction and 1000 SPD entry(ies) in each SPD. Only outbound traffic is matched and only the last rule is the matching rule. DUT1 tested with Intel-XL710.

  • [Ver] TG vefication: In MaxReceivedRate tests TG sends traffic at line rate and reports total received packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. The DUT does SPD lookup with only the lowest priority rule matching the traffic. The action of the matching rule is BYPASS. No encryption or authentication is done.

  • [Ref] Applicable standard specifications: RFC4301 and RFC2544.

 Test Name 

 Maximum Receive Rate trial [Mpps] 

 64b-1t1c-ethip4ipsec1000spe-ip4base- 
policy-outbound-nocrypto-mrr

 [0.31, 0.31, 0.31, 0.31, 0.31, 0.31, 0.31, 0.31, 0.31, 0.31] 

 64b-2t2c-ethip4ipsec1000spe-ip4base- 
policy-outbound-nocrypto-mrr

 [0.62, 0.62, 0.62, 0.62, 0.62, 0.62, 0.62, 0.62, 0.62, 0.62] 

 64b-4t4c-ethip4ipsec1000spe-ip4base- 
policy-outbound-nocrypto-mrr

 [1.23, 1.23, 1.23, 1.23, 1.23, 1.23, 1.23, 1.23, 1.23, 1.23] 

2n1l-40ge2p1xl710-ethip4ipsec1000tnlsw-ip4base-int-aes128cbc-hmac512sha-udir-mrr

RFC2544: Pkt throughput IPv4 IPsec tunnel mode.

  • [Top] Network Topologies: TG-DUT1-TG 2-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 on TG-DUT1, Eth-IPv4-IPSec on DUT1-TG.

  • [Cfg] DUT configuration: DUT1 is configured with multiple IPsec tunnels between it and TG. DUT gets IPv4 traffic from TG, encrypts it and sends back to TG.

  • [Ver] TG vefication: In MaxReceivedRate tests TG sends traffic at line rate and reports total received packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains one L3 flow-groups (number of flows per flow-group equals to number of IPSec tunnels) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv4 destination address) field is applied to the stream.

  • [Ref] Applicable standard specifications: RFC4303 and RFC2544.

 Test Name 

 Maximum Receive Rate trial [Mpps] 

 1518b-1t1c-ethip4ipsec1000tnlsw-ip4base- 
int-aes128cbc-hmac512sha-udir-mrr

 [0.11, 0.11, 0.11, 0.11, 0.11, 0.11, 0.11, 0.11, 0.11, 0.11] 

 1518b-2t2c-ethip4ipsec1000tnlsw-ip4base- 
int-aes128cbc-hmac512sha-udir-mrr

 [0.21, 0.21, 0.21, 0.21, 0.21, 0.21, 0.21, 0.21, 0.21, 0.21] 

 1518b-4t4c-ethip4ipsec1000tnlsw-ip4base- 
int-aes128cbc-hmac512sha-udir-mrr

 [0.43, 0.43, 0.43, 0.43, 0.43, 0.43, 0.43, 0.43, 0.43, 0.43] 

 imix-1t1c-ethip4ipsec1000tnlsw-ip4base- 
int-aes128cbc-hmac512sha-udir-mrr

 [0.24, 0.24, 0.24, 0.24, 0.24, 0.24, 0.24, 0.24, 0.24, 0.24] 

 imix-2t2c-ethip4ipsec1000tnlsw-ip4base- 
int-aes128cbc-hmac512sha-udir-mrr

 [0.48, 0.48, 0.48, 0.48, 0.48, 0.48, 0.48, 0.48, 0.48, 0.48] 

 imix-4t4c-ethip4ipsec1000tnlsw-ip4base- 
int-aes128cbc-hmac512sha-udir-mrr

 [0.96, 0.96, 0.96, 0.96, 0.96, 0.96, 0.96, 0.96, 0.96, 0.96] 

2n1l-40ge2p1xl710-ethip4ipsec1000tnlsw-ip4base-int-aes128gcm-udir-mrr

RFC2544: Pkt throughput IPv4 IPsec tunnel mode.

  • [Top] Network Topologies: TG-DUT1-TG 2-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 on TG-DUT1, Eth-IPv4-IPSec on DUT1-TG.

  • [Cfg] DUT configuration: DUT1 is configured with multiple IPsec tunnels between it and TG. DUT gets IPv4 traffic from TG, encrypts it and sends back to TG.

  • [Ver] TG vefication: In MaxReceivedRate tests TG sends traffic at line rate and reports total received packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains one L3 flow-groups (number of flows per flow-group equals to number of IPSec tunnels) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv4 destination address) field is applied to the stream.

  • [Ref] Applicable standard specifications: RFC4303 and RFC2544.

 Test Name 

 Maximum Receive Rate trial [Mpps] 

 1518b-1t1c-ethip4ipsec1000tnlsw-ip4base- 
int-aes128gcm-udir-mrr

 [0.50, 0.50, 0.50, 0.50, 0.50, 0.50, 0.50, 0.50, 0.50, 0.50] 

 1518b-2t2c-ethip4ipsec1000tnlsw-ip4base- 
int-aes128gcm-udir-mrr

 [1.01, 1.01, 1.01, 1.00, 1.01, 1.00, 1.01, 1.00, 1.00, 1.00] 

 1518b-4t4c-ethip4ipsec1000tnlsw-ip4base- 
int-aes128gcm-udir-mrr

 [1.92, 1.92, 1.92, 1.92, 1.92, 1.92, 1.92, 1.92, 1.92, 1.92] 

 imix-1t1c-ethip4ipsec1000tnlsw-ip4base- 
int-aes128gcm-udir-mrr

 [1.29, 1.29, 1.29, 1.29, 1.29, 1.29, 1.29, 1.29, 1.29, 1.29] 

 imix-2t2c-ethip4ipsec1000tnlsw-ip4base- 
int-aes128gcm-udir-mrr

 [2.58, 2.58, 2.58, 2.58, 2.58, 2.58, 2.58, 2.58, 2.58, 2.58] 

 imix-4t4c-ethip4ipsec1000tnlsw-ip4base- 
int-aes128gcm-udir-mrr

 [5.15, 5.16, 5.15, 5.15, 5.15, 5.15, 5.15, 5.15, 5.14, 5.14] 

2n1l-40ge2p1xl710-ethip4ipsec1000tnlsw-ip4base-int-aes256gcm-udir-mrr

RFC2544: Pkt throughput IPv4 IPsec tunnel mode.

  • [Top] Network Topologies: TG-DUT1-TG 2-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 on TG-DUT1, Eth-IPv4-IPSec on DUT1-TG.

  • [Cfg] DUT configuration: DUT1 is configured with multiple IPsec tunnels between it and TG. DUT gets IPv4 traffic from TG, encrypts it and sends back to TG.

  • [Ver] TG vefication: In MaxReceivedRate tests TG sends traffic at line rate and reports total received packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains one L3 flow-groups (number of flows per flow-group equals to number of IPSec tunnels) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv4 destination address) field is applied to the stream.

  • [Ref] Applicable standard specifications: RFC4303 and RFC2544.

 Test Name 

 Maximum Receive Rate trial [Mpps] 

 1518b-1t1c-ethip4ipsec1000tnlsw-ip4base- 
int-aes256gcm-udir-mrr

 [0.43, 0.43, 0.43, 0.43, 0.43, 0.43, 0.43, 0.43, 0.43, 0.43] 

 1518b-2t2c-ethip4ipsec1000tnlsw-ip4base- 
int-aes256gcm-udir-mrr

 [0.85, 0.85, 0.85, 0.85, 0.85, 0.85, 0.85, 0.85, 0.85, 0.85] 

 1518b-4t4c-ethip4ipsec1000tnlsw-ip4base- 
int-aes256gcm-udir-mrr

 [1.69, 1.69, 1.69, 1.69, 1.69, 1.69, 1.69, 1.69, 1.69, 1.69] 

 imix-1t1c-ethip4ipsec1000tnlsw-ip4base- 
int-aes256gcm-udir-mrr

 [1.15, 1.15, 1.15, 1.15, 1.15, 1.15, 1.15, 1.15, 1.15, 1.15] 

 imix-2t2c-ethip4ipsec1000tnlsw-ip4base- 
int-aes256gcm-udir-mrr

 [2.31, 2.31, 2.31, 2.31, 2.31, 2.30, 2.31, 2.31, 2.31, 2.31] 

 imix-4t4c-ethip4ipsec1000tnlsw-ip4base- 
int-aes256gcm-udir-mrr

 [4.61, 4.60, 4.60, 4.61, 4.60, 4.60, 4.60, 4.59, 4.60, 4.60] 

2n1l-40ge2p1xl710-ethip4ipsec1000tnlsw-ip4base-policy-aes256gcm-udir-mrr

RFC2544: Pkt throughput IPv4 IPsec tunnel mode.

  • [Top] Network Topologies: TG-DUT1-TG 2-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 on TG-DUT1, Eth-IPv4-IPSec on DUT1-TG.

  • [Cfg] DUT configuration: DUT1 is configured with multiple IPsec tunnels between it and TG. DUT gets IPv4 traffic from TG, encrypts it and sends back to TG.

  • [Ver] TG vefication: In MaxReceivedRate tests TG sends traffic at line rate and reports total received packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains one L3 flow-groups (number of flows per flow-group equals to number of IPSec tunnels) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv4 destination address) field is applied to the stream.

  • [Ref] Applicable standard specifications: RFC4303 and RFC2544.

 Test Name 

 Maximum Receive Rate trial [Mpps] 

 64b-1t1c-ethip4ipsec1000tnlsw-ip4base- 
policy-aes256gcm-udir-mrr

 [0.37, 0.38, 0.38, 0.38, 0.38, 0.38, 0.38, 0.38, 0.37, 0.38] 

 64b-2t2c-ethip4ipsec1000tnlsw-ip4base- 
policy-aes256gcm-udir-mrr

 [0.74, 0.75, 0.75, 0.76, 0.75, 0.75, 0.75, 0.75, 0.75, 0.75] 

 64b-4t4c-ethip4ipsec1000tnlsw-ip4base- 
policy-aes256gcm-udir-mrr

 [1.51, 1.51, 1.51, 1.51, 1.50, 1.50, 1.51, 1.51, 1.51, 1.51] 

2n1l-40ge2p1xl710-ethip4ipsec100spe-cache-ip4base-policy-outbound-nocrypto-mrr

RFC4301: SPD lookup performance

  • [Top] Network Topologies: TG-DUT1-TG 2-node circular topology

with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 for IPv4 routing.

  • [Cfg] DUT configuration: DUT1 is configured with IPv4 routing, two static IPv4 /24 route entries, one SPD on each outbound interface in each direction and 100 SPD entry(ies) in each SPD. Only outbound traffic is matched and only the last rule is the matching rule. SPD flow-cache for IPv4 outbound traffic is enabled. DUT1 is tested with Intel-XL710.

  • [Ver] TG vefication: In MaxReceivedRate tests TG sends traffic at line rate and reports total received packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. The DUT does SPD lookup with only the lowest priority rule matching the traffic. The action of the matching rule is BYPASS. No encryption or authentication is done.

  • [Ref] Applicable standard specifications: RFC4301 and RFC2544.

 Test Name 

 Maximum Receive Rate trial [Mpps] 

 64b-1t1c-ethip4ipsec100spe-cache- 
ip4base-policy-outbound-nocrypto-mrr

 [4.43, 4.43, 4.43, 4.40, 4.39, 4.41, 4.39, 4.41, 4.40, 4.39] 

 64b-2t2c-ethip4ipsec100spe-cache- 
ip4base-policy-outbound-nocrypto-mrr

 [8.95, 8.94, 8.93, 8.94, 8.94, 8.92, 8.93, 8.92, 8.94, 8.91] 

 64b-4t4c-ethip4ipsec100spe-cache- 
ip4base-policy-outbound-nocrypto-mrr

 [15.63, 15.67, 15.61, 15.65, 15.61, 15.66, 15.66, 15.64, 15.61, 15.60] 

2n1l-40ge2p1xl710-ethip4ipsec100spe-ip4base-policy-outbound-nocrypto-mrr

RFC4301: SPD lookup performance

  • [Top] Network Topologies: TG-DUT1-TG 2-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 for IPv4 routing.

  • [Cfg] DUT configuration: DUT1 is configured with IPv4 routing, two static IPv4 /24 route entries, one SPD on each outbound interface in each direction and 100 SPD entry(ies) in each SPD. Only outbound traffic is matched and only the last rule is the matching rule. DUT1 tested with Intel-XL710.

  • [Ver] TG vefication: In MaxReceivedRate tests TG sends traffic at line rate and reports total received packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. The DUT does SPD lookup with only the lowest priority rule matching the traffic. The action of the matching rule is BYPASS. No encryption or authentication is done.

  • [Ref] Applicable standard specifications: RFC4301 and RFC2544.

 Test Name 

 Maximum Receive Rate trial [Mpps] 

 64b-1t1c-ethip4ipsec100spe-ip4base- 
policy-outbound-nocrypto-mrr

 [2.27, 2.27, 2.27, 2.27, 2.27, 2.28, 2.28, 2.27, 2.27, 2.27] 

 64b-2t2c-ethip4ipsec100spe-ip4base- 
policy-outbound-nocrypto-mrr

 [4.53, 4.54, 4.54, 4.53, 4.54, 4.54, 4.53, 4.53, 4.53, 4.52] 

 64b-4t4c-ethip4ipsec100spe-ip4base- 
policy-outbound-nocrypto-mrr

 [8.64, 8.67, 8.64, 8.66, 8.63, 8.66, 8.65, 8.63, 8.62, 8.62] 

2n1l-40ge2p1xl710-ethip4ipsec1spe-cache-ip4base-policy-outbound-nocrypto-mrr

RFC4301: SPD lookup performance

  • [Top] Network Topologies: TG-DUT1-TG 2-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 for IPv4 routing.

  • [Cfg] DUT configuration: DUT1 is configured with IPv4 routing, two static IPv4 /24 route entries, one SPD on each outbound interface in each direction and 1 SPD entry(ies) in each SPD. Only outbound traffic is matched and only the last rule is the matching rule. SPD flow-cache for IPv4 outbound traffic is enabled. DUT1 is tested with Intel-XL710.

  • [Ver] TG vefication: In MaxReceivedRate tests TG sends traffic at line rate and reports total received packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. The DUT does SPD lookup with only the lowest priority rule matching the traffic. The action of the matching rule is BYPASS. No encryption or authentication is done.

  • [Ref] Applicable standard specifications: RFC4301 and RFC2544.

 Test Name 

 Maximum Receive Rate trial [Mpps] 

 64b-1t1c-ethip4ipsec1spe-cache- 
ip4base-policy-outbound-nocrypto-mrr

 [4.41, 4.43, 4.41, 4.42, 4.40, 4.40, 4.40, 4.41, 4.41, 4.38] 

 64b-2t2c-ethip4ipsec1spe-cache- 
ip4base-policy-outbound-nocrypto-mrr

 [8.90, 8.91, 8.90, 8.90, 8.90, 8.90, 8.88, 8.88, 8.89, 8.89] 

 64b-4t4c-ethip4ipsec1spe-cache- 
ip4base-policy-outbound-nocrypto-mrr

 [15.80, 15.78, 15.80, 15.75, 15.80, 15.76, 15.75, 15.79, 15.76, 15.75] 

2n1l-40ge2p1xl710-ethip4ipsec1spe-ip4base-policy-outbound-nocrypto-mrr

RFC4301: SPD lookup performance

  • [Top] Network Topologies: TG-DUT1-TG 2-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 for IPv4 routing.

  • [Cfg] DUT configuration: DUT1 is configured with IPv4 routing, two static IPv4 /24 route entries, one SPD on each outbound interface in each direction and 1 SPD entry(ies) in each SPD. Only outbound traffic is matched and only the last rule is the matching rule. DUT1 tested with Intel-XL710.

  • [Ver] TG vefication: In MaxReceivedRate tests TG sends traffic at line rate and reports total received packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. The DUT does SPD lookup with only the lowest priority rule matching the traffic. The action of the matching rule is BYPASS. No encryption or authentication is done.

  • [Ref] Applicable standard specifications: RFC4301 and RFC2544.

 Test Name 

 Maximum Receive Rate trial [Mpps] 

 64b-1t1c-ethip4ipsec1spe-ip4base- 
policy-outbound-nocrypto-mrr

 [5.30, 5.30, 5.30, 5.29, 5.27, 5.29, 5.28, 5.28, 5.30, 5.26] 

 64b-2t2c-ethip4ipsec1spe-ip4base- 
policy-outbound-nocrypto-mrr

 [10.44, 10.46, 10.44, 10.41, 10.40, 10.42, 10.37, 10.39, 10.44, 10.36] 

 64b-4t4c-ethip4ipsec1spe-ip4base- 
policy-outbound-nocrypto-mrr

 [18.54, 18.59, 18.53, 18.55, 18.53, 18.55, 18.53, 18.54, 18.59, 18.47] 

2n1l-40ge2p1xl710-ethip4ipsec1tnlsw-ip4base-policy-aes256gcm-udir-mrr

RFC2544: Pkt throughput IPv4 IPsec tunnel mode.

  • [Top] Network Topologies: TG-DUT1-TG 2-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 on TG-DUT1, Eth-IPv4-IPSec on DUT1-TG.

  • [Cfg] DUT configuration: DUT1 is configured with multiple IPsec tunnels between it and TG. DUT gets IPv4 traffic from TG, encrypts it and sends back to TG.

  • [Ver] TG vefication: In MaxReceivedRate tests TG sends traffic at line rate and reports total received packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains one L3 flow-groups (number of flows per flow-group equals to number of IPSec tunnels) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv4 destination address) field is applied to the stream.

  • [Ref] Applicable standard specifications: RFC4303 and RFC2544.

 Test Name 

 Maximum Receive Rate trial [Mpps] 

 64b-1t1c-ethip4ipsec1tnlsw-ip4base- 
policy-aes256gcm-udir-mrr

 [2.31, 2.31, 2.31, 2.31, 2.31, 2.31, 2.31, 2.31, 2.31, 2.31] 

 64b-2t2c-ethip4ipsec1tnlsw-ip4base- 
policy-aes256gcm-udir-mrr

 [2.31, 2.31, 2.31, 2.31, 2.31, 2.31, 2.31, 2.31, 2.31, 2.31] 

 64b-4t4c-ethip4ipsec1tnlsw-ip4base- 
policy-aes256gcm-udir-mrr

 [2.32, 2.31, 2.31, 2.31, 2.31, 2.31, 2.31, 2.31, 2.31, 2.31] 

2n1l-40ge2p1xl710-ethip4ipsec40tnlsw-ip4base-policy-aes256gcm-udir-mrr

RFC2544: Pkt throughput IPv4 IPsec tunnel mode.

  • [Top] Network Topologies: TG-DUT1-TG 2-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 on TG-DUT1, Eth-IPv4-IPSec on DUT1-TG.

  • [Cfg] DUT configuration: DUT1 is configured with multiple IPsec tunnels between it and TG. DUT gets IPv4 traffic from TG, encrypts it and sends back to TG.

  • [Ver] TG vefication: In MaxReceivedRate tests TG sends traffic at line rate and reports total received packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains one L3 flow-groups (number of flows per flow-group equals to number of IPSec tunnels) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv4 destination address) field is applied to the stream.

  • [Ref] Applicable standard specifications: RFC4303 and RFC2544.

 Test Name 

 Maximum Receive Rate trial [Mpps] 

 64b-1t1c-ethip4ipsec40tnlsw-ip4base- 
policy-aes256gcm-udir-mrr

 [1.89, 1.89, 1.89, 1.89, 1.89, 1.89, 1.89, 1.89, 1.89, 1.90] 

 64b-2t2c-ethip4ipsec40tnlsw-ip4base- 
policy-aes256gcm-udir-mrr

 [3.81, 3.81, 3.80, 3.82, 3.81, 3.81, 3.80, 3.81, 3.81, 3.81] 

 64b-4t4c-ethip4ipsec40tnlsw-ip4base- 
policy-aes256gcm-udir-mrr

 [7.69, 7.69, 7.70, 7.69, 7.69, 7.69, 7.68, 7.69, 7.69, 7.68] 

2n1l-40ge2p1xl710-ethip4ipsec4tnlsw-ip4base-int-aes128cbc-hmac512sha-udir-mrr

RFC2544: Pkt throughput IPv4 IPsec tunnel mode.

  • [Top] Network Topologies: TG-DUT1-TG 2-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 on TG-DUT1, Eth-IPv4-IPSec on DUT1-TG.

  • [Cfg] DUT configuration: DUT1 is configured with multiple IPsec tunnels between it and TG. DUT gets IPv4 traffic from TG, encrypts it and sends back to TG.

  • [Ver] TG vefication: In MaxReceivedRate tests TG sends traffic at line rate and reports total received packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains one L3 flow-groups (number of flows per flow-group equals to number of IPSec tunnels) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv4 destination address) field is applied to the stream.

  • [Ref] Applicable standard specifications: RFC4303 and RFC2544.

 Test Name 

 Maximum Receive Rate trial [Mpps] 

 1518b-1t1c-ethip4ipsec4tnlsw-ip4base- 
int-aes128cbc-hmac512sha-udir-mrr

 [0.11, 0.11, 0.11, 0.11, 0.11, 0.11, 0.11, 0.11, 0.11, 0.11] 

 1518b-2t2c-ethip4ipsec4tnlsw-ip4base- 
int-aes128cbc-hmac512sha-udir-mrr

 [0.22, 0.22, 0.22, 0.22, 0.22, 0.22, 0.22, 0.22, 0.22, 0.22] 

 1518b-4t4c-ethip4ipsec4tnlsw-ip4base- 
int-aes128cbc-hmac512sha-udir-mrr

 [0.43, 0.43, 0.43, 0.43, 0.43, 0.43, 0.43, 0.43, 0.43, 0.43] 

 imix-1t1c-ethip4ipsec4tnlsw-ip4base- 
int-aes128cbc-hmac512sha-udir-mrr

 [0.25, 0.25, 0.25, 0.25, 0.25, 0.25, 0.25, 0.25, 0.25, 0.25] 

 imix-2t2c-ethip4ipsec4tnlsw-ip4base- 
int-aes128cbc-hmac512sha-udir-mrr

 [0.50, 0.50, 0.50, 0.50, 0.50, 0.50, 0.50, 0.50, 0.50, 0.50] 

 imix-4t4c-ethip4ipsec4tnlsw-ip4base- 
int-aes128cbc-hmac512sha-udir-mrr

 [1.00, 1.00, 1.00, 1.00, 1.00, 1.00, 1.00, 1.00, 1.00, 1.00] 

2n1l-40ge2p1xl710-ethip4ipsec4tnlsw-ip4base-int-aes128gcm-udir-mrr

RFC2544: Pkt throughput IPv4 IPsec tunnel mode.

  • [Top] Network Topologies: TG-DUT1-TG 2-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 on TG-DUT1, Eth-IPv4-IPSec on DUT1-TG.

  • [Cfg] DUT configuration: DUT1 is configured with multiple IPsec tunnels between it and TG. DUT gets IPv4 traffic from TG, encrypts it and sends back to TG.

  • [Ver] TG vefication: In MaxReceivedRate tests TG sends traffic at line rate and reports total received packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains one L3 flow-groups (number of flows per flow-group equals to number of IPSec tunnels) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv4 destination address) field is applied to the stream.

  • [Ref] Applicable standard specifications: RFC4303 and RFC2544.

 Test Name 

 Maximum Receive Rate trial [Mpps] 

 1518b-1t1c-ethip4ipsec4tnlsw-ip4base- 
int-aes128gcm-udir-mrr

 [0.52, 0.52, 0.52, 0.52, 0.52, 0.52, 0.52, 0.52, 0.52, 0.52] 

 1518b-2t2c-ethip4ipsec4tnlsw-ip4base- 
int-aes128gcm-udir-mrr

 [1.04, 1.05, 1.04, 1.04, 1.04, 1.04, 1.04, 1.04, 1.04, 1.04] 

 1518b-4t4c-ethip4ipsec4tnlsw-ip4base- 
int-aes128gcm-udir-mrr

 [1.92, 1.92, 1.92, 1.92, 1.92, 1.92, 1.92, 1.92, 1.92, 1.92] 

 imix-1t1c-ethip4ipsec4tnlsw-ip4base- 
int-aes128gcm-udir-mrr

 [1.42, 1.42, 1.42, 1.41, 1.41, 1.42, 1.42, 1.41, 1.42, 1.42] 

 imix-2t2c-ethip4ipsec4tnlsw-ip4base- 
int-aes128gcm-udir-mrr

 [2.85, 2.85, 2.85, 2.84, 2.84, 2.84, 2.84, 2.84, 2.84, 2.83] 

 imix-4t4c-ethip4ipsec4tnlsw-ip4base- 
int-aes128gcm-udir-mrr

 [5.70, 5.70, 5.70, 5.70, 5.69, 5.69, 5.69, 5.68, 5.69, 5.69] 

2n1l-40ge2p1xl710-ethip4ipsec4tnlsw-ip4base-int-aes256gcm-udir-mrr

RFC2544: Pkt throughput IPv4 IPsec tunnel mode.

  • [Top] Network Topologies: TG-DUT1-TG 2-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 on TG-DUT1, Eth-IPv4-IPSec on DUT1-TG.

  • [Cfg] DUT configuration: DUT1 is configured with multiple IPsec tunnels between it and TG. DUT gets IPv4 traffic from TG, encrypts it and sends back to TG.

  • [Ver] TG vefication: In MaxReceivedRate tests TG sends traffic at line rate and reports total received packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains one L3 flow-groups (number of flows per flow-group equals to number of IPSec tunnels) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv4 destination address) field is applied to the stream.

  • [Ref] Applicable standard specifications: RFC4303 and RFC2544.

 Test Name 

 Maximum Receive Rate trial [Mpps] 

 1518b-1t1c-ethip4ipsec4tnlsw-ip4base- 
int-aes256gcm-udir-mrr

 [0.44, 0.44, 0.44, 0.44, 0.44, 0.44, 0.44, 0.44, 0.44, 0.44] 

 1518b-2t2c-ethip4ipsec4tnlsw-ip4base- 
int-aes256gcm-udir-mrr

 [0.88, 0.88, 0.88, 0.88, 0.88, 0.88, 0.88, 0.88, 0.88, 0.88] 

 1518b-4t4c-ethip4ipsec4tnlsw-ip4base- 
int-aes256gcm-udir-mrr

 [1.76, 1.76, 1.76, 1.76, 1.76, 1.76, 1.76, 1.76, 1.76, 1.76] 

 imix-1t1c-ethip4ipsec4tnlsw-ip4base- 
int-aes256gcm-udir-mrr

 [1.25, 1.25, 1.25, 1.25, 1.25, 1.25, 1.25, 1.25, 1.25, 1.25] 

 imix-2t2c-ethip4ipsec4tnlsw-ip4base- 
int-aes256gcm-udir-mrr

 [2.51, 2.51, 2.51, 2.52, 2.52, 2.51, 2.52, 2.52, 2.51, 2.51] 

 imix-4t4c-ethip4ipsec4tnlsw-ip4base- 
int-aes256gcm-udir-mrr

 [5.04, 5.05, 5.04, 5.04, 5.03, 5.04, 5.03, 5.03, 5.03, 5.03]