3n-tsh-x520

10ge2p1x520-dot1q-ip4base-ndrpdr

RFC2544: Pkt throughput IPv4 routing with IEEE 802.1Q test cases

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 for IPv4 routing. IEEE 802.1Q tagging is applied on link between DUT1 and DUT2.

  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv4 routing and two static IPv4 /30 route entries. DUT1 and DUT2 tested with Intel-X520-DA2.

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 254 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.

  • [Ref] Applicable standard specifications: RFC2544.

 Test Name 

 Throughput: 
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)

One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)

 64b-1t1c-dot1q-ip4base-ndrpdr 

 1.  4.88       3.28 
2. 4.90 3.29

3. 24 57 70 24 39 45
4. 61 82 110 64 75 84
5. 142 164 186 152 174 198

 64b-2t2c-dot1q-ip4base-ndrpdr 

 1.  6.91       4.64 
2. 6.98 4.69

3. 23 41 47 24 34 44
4. 37 52 58 57 71 79
5. 78 94 112 81 95 105

 64b-4t4c-dot1q-ip4base-ndrpdr 

 1.  5.75       3.87 
2. 7.84 5.27

3. 23 26 31 23 25 29
4. 36 54 61 36 50 59
5. 57 69 83 59 73 83

10ge2p1x520-ethip4-ip4base-ndrpdr

RFC2544: Pkt throughput IPv4 routing test cases

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 for IPv4 routing.

  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv4 routing and two static IPv4 /24 route entries. DUT1 and DUT2 tested with Intel-X520-DA2.

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.

  • [Ref] Applicable standard specifications: RFC2544.

 Test Name 

 Throughput: 
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)

One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)

 64b-1t1c-ethip4-ip4base-ndrpdr 

 1.  5.29       3.56 
2. 5.35 3.59

3. 23 42 57 24 38 49
4. 43 73 84 47 70 85
5. 128 149 170 135 160 180

 64b-2t2c-ethip4-ip4base-ndrpdr 

 1.  7.13       4.79 
2. 7.16 4.81

3. 22 27 55 23 38 48
4. 41 68 77 42 64 72
5. 72 86 101 75 87 97

 64b-4t4c-ethip4-ip4base-ndrpdr 

 1.  7.15       4.80 
2. 7.90 5.31

3. 23 40 52 23 29 32
4. 36 54 62 39 55 63
5. 59 70 80 56 67 79

10ge2p1x520-ethip4-ip4scale200k-ndrpdr

RFC2544: Pkt throughput IPv4 routing test cases

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 for IPv4 routing.

  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv4 routing and 2x100k static IPv4 /32 route entries. DUT1 and DUT2 tested with Intel-X520-DA2.

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100k flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.

  • [Ref] Applicable standard specifications: RFC2544.

 Test Name 

 Throughput: 
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)

One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)

 64b-1t1c- 
ethip4-ip4scale200k-ndrpdr

 1.  3.75       2.52 
2. 4.31 2.90

3. 23 39 69 23 46 50
4. 66 87 105 54 81 97
5. 118 137 161 121 148 173

 64b-2t2c- 
ethip4-ip4scale200k-ndrpdr

 1.  6.09       4.09 
2. 6.21 4.18

3. 23 30 39 24 52 67
4. 46 76 87 52 81 91
5. 77 97 115 81 98 110

 64b-4t4c- 
ethip4-ip4scale200k-ndrpdr

 1.  5.99       4.03 
2. 7.47 5.02

3. 23 32 44 23 28 35
4. 42 64 73 41 61 71
5. 70 86 95 65 79 93

10ge2p1x520-ethip4-ip4scale20k-ndrpdr

RFC2544: Pkt throughput IPv4 routing test cases

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 for IPv4 routing.

  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv4 routing and 2x10k static IPv4 /32 route entries. DUT1 and DUT2 tested with Intel-X520-DA2.

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.

  • [Ref] Applicable standard specifications: RFC2544.

 Test Name 

 Throughput: 
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)

One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)

 64b-1t1c- 
ethip4-ip4scale20k-ndrpdr

 1.  4.92       3.30 
2. 4.94 3.32

3. 23 40 78 23 36 45
4. 71 95 108 48 74 106
5. 125 143 163 131 152 176

 64b-2t2c- 
ethip4-ip4scale20k-ndrpdr

 1.  6.16       4.14 
2. 6.38 4.28

3. 22 30 34 23 27 43
4. 40 50 61 42 61 70
5. 67 81 101 79 95 110

 64b-4t4c- 
ethip4-ip4scale20k-ndrpdr

 1.  7.62       5.12 
2. 7.94 5.33

3. 23 43 55 24 27 32
4. 34 53 64 33 49 65
5. 58 71 85 61 76 88

10ge2p1x520-ethip4-ip4scale2m-ndrpdr

RFC2544: Pkt throughput IPv4 routing test cases

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 for IPv4 routing.

  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv4 routing and 2x1M static IPv4 /32 route entries. DUT1 and DUT2 tested with Intel-X520-DA2.

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 1M flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.

  • [Ref] Applicable standard specifications: RFC2544.

 Test Name 

 Throughput: 
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)

One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)

 64b-1t1c- 
ethip4-ip4scale2m-ndrpdr

 1.  3.71       2.49 
2. 4.16 2.79

3. 24 44 53 26 40 49
4. 50 82 99 48 88 99
5. 115 140 155 113 137 166

 64b-2t2c- 
ethip4-ip4scale2m-ndrpdr

 1.  3.91       2.62 
2. 6.22 4.18

3. 23 57 67 24 51 63
4. 52 78 87 59 86 94
5. 78 98 121 82 100 113

 64b-4t4c- 
ethip4-ip4scale2m-ndrpdr

 1.  2.74       1.84 
2. 7.40 4.98

3. 23 45 53 23 24 26
4. 43 58 69 38 60 67
5. 65 77 91 64 79 96

10ge2p1x520-ethip4udp-ip4base-iacl50sf-10kflows-ndrpdr

RFC2544: Packet throughput IPv4 test cases with ACL

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4-UDP for IPv4 routing.

  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv4 routing and one static IPv4 /24 route entries. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Intel-X520-DA2.

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.

  • [Ref] Applicable standard specifications: RFC2544.

 Test Name 

 Throughput: 
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)

One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)

 64b-1t1c-ethip4udp- 
ip4base-iacl50sf-10kflows-ndrpdr

 1.  3.53       2.37 
2. 3.57 2.40

3. 24 42 58 24 46 65
4. 48 89 112 55 80 94
5. 102 130 150 100 126 150

 64b-2t2c-ethip4udp- 
ip4base-iacl50sf-10kflows-ndrpdr

 1.  5.00       3.36 
2. 5.05 3.39

3. 23 68 83 24 35 45
4. 51 78 91 42 67 76
5. 61 82 101 55 80 98

 64b-4t4c-ethip4udp- 
ip4base-iacl50sf-10kflows-ndrpdr

 1.  5.32       3.58 
2. 7.55 5.08

3. 24 25 27 24 25 28
4. 38 62 70 39 61 69
5. 71 85 97 67 78 95

10ge2p1x520-ethip4udp-ip4base-iacl50sl-10kflows-ndrpdr

RFC2544: Packet throughput IPv4 test cases with ACL

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4-UDP for IPv4 routing.

  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv4 routing and one static IPv4 /24 route entries. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Intel-X520-DA2.

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.

  • [Ref] Applicable standard specifications: RFC2544.

 Test Name 

 Throughput: 
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)

One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)

 64b-1t1c-ethip4udp- 
ip4base-iacl50sl-10kflows-ndrpdr

 1.  3.36       2.26 
2. 3.39 2.28

3. 24 38 52 24 61 85
4. 46 91 103 56 74 90
5. 94 110 126 90 108 127

 64b-2t2c-ethip4udp- 
ip4base-iacl50sl-10kflows-ndrpdr

 1.  5.07       3.41 
2. 5.09 3.42

3. 24 45 60 24 48 66
4. 39 62 71 38 70 79
5. 64 75 91 57 70 80

 64b-4t4c-ethip4udp- 
ip4base-iacl50sl-10kflows-ndrpdr

 1.  6.60       4.44 
2. 7.94 5.34

3. 24 32 41 25 33 48
4. 44 64 72 45 63 74
5. 69 86 96 67 83 95

10ge2p1x520-ethip4udp-ip4base-oacl50sf-10kflows-ndrpdr

RFC2544: Packet throughput IPv4 test cases with ACL

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4-UDP for IPv4 routing.

  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv4 routing and one static IPv4 /24 route entries. Required ACL rules are applied to output paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Intel-X520-DA2.

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.

  • [Ref] Applicable standard specifications: RFC2544.

 Test Name 

 Throughput: 
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)

One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)

 64b-1t1c-ethip4udp- 
ip4base-oacl50sf-10kflows-ndrpdr

 1.  3.45       2.32 
2. 3.47 2.33

3. 24 29 41 24 28 53
4. 44 85 96 52 81 92
5. 97 116 139 96 120 139

 64b-2t2c-ethip4udp- 
ip4base-oacl50sf-10kflows-ndrpdr

 1.  4.81       3.23 
2. 4.86 3.27

3. 24 30 38 25 29 36
4. 51 87 96 70 82 90
5. 73 92 103 74 93 107

 64b-4t4c-ethip4udp- 
ip4base-oacl50sf-10kflows-ndrpdr

 1.  5.85       3.93 
2. 7.73 5.20

3. 26 56 63 26 56 66
4. 39 61 70 42 62 72
5. 75 87 98 67 88 101

10ge2p1x520-ethip4udp-ip4base-oacl50sl-10kflows-ndrpdr

RFC2544: Packet throughput IPv4 test cases with ACL

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4-UDP for IPv4 routing.

  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv4 routing and one static IPv4 /24 route entries. Required ACL rules are applied to output paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Intel-X520-DA2.

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.

  • [Ref] Applicable standard specifications: RFC2544.

 Test Name 

 Throughput: 
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)

One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)

 64b-1t1c-ethip4udp- 
ip4base-oacl50sl-10kflows-ndrpdr

 1.  3.25       2.19 
2. 3.29 2.21

3. 24 45 58 25 33 80
4. 54 101 118 49 88 107
5. 99 120 142 94 129 147

 64b-2t2c-ethip4udp- 
ip4base-oacl50sl-10kflows-ndrpdr

 1.  4.90       3.29 
2. 4.98 3.34

3. 24 26 62 25 27 48
4. 30 49 86 32 49 62
5. 84 99 111 71 84 100

 64b-4t4c-ethip4udp- 
ip4base-oacl50sl-10kflows-ndrpdr

 1.  3.59       2.41 
2. 7.90 5.31

3. 25 30 35 25 33 56
4. 46 67 74 47 65 76
5. 69 86 98 70 85 98