3n-tsh-x520

10ge2p1x520-dot1q-l2bdbasemaclrn-ndrpdr

RFC2544: Pkt throughput L2BD with IEEE 802.1Q test cases

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 for L2 switching of IPv4. IEEE 802.1Q tagging is applied on link between DUT1 and DUT2.

  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 bridge domain and MAC learning enabled. DUT1 and DUT2 are tested with Intel-X520-DA2.

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 254 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.

  • [Ref] Applicable standard specifications: RFC2544.

 Test Name 

 Throughput: 
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)

One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)

 64b-1t1c- 
dot1q-l2bdbasemaclrn-ndrpdr

 1.  2.29       1.54 
2. 4.48 3.01

3. 25 83 111 26 51 103
4. 52 100 114 55 105 117
5. 160 212 247 167 218 240

 64b-2t2c- 
dot1q-l2bdbasemaclrn-ndrpdr

 1.  5.03       3.38 
2. 6.53 4.39

3. 25 44 62 25 42 60
4. 49 95 105 51 96 113
5. 113 146 177 116 148 180

 64b-4t4c- 
dot1q-l2bdbasemaclrn-ndrpdr

 1.  7.97       5.36 
2. 7.97 5.36

3. 25 49 66 26 29 55
4. 34 64 75 27 31 36
5. 69 88 95 70 89 97

10ge2p1x520-dot1q-l2xcbase-ndrpdr

RFC2544: Pkt throughput L2XC with IEEE 802.1Q test cases

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 for L2 cross connect. IEEE 802.1Q tagging is applied on link between DUT1 and DUT2.

  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 cross- connect. DUT1 and DUT2 are tested with Intel-X520-DA2.

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 254 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.

  • [Ref] Applicable standard specifications: RFC2544.

 Test Name 

 Throughput: 
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)

One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)

 64b-1t1c-dot1q-l2xcbase-ndrpdr 

 1.  4.40       2.96 
2. 5.25 3.53

3. 22 83 96 22 95 104
4. 56 86 100 60 85 101
5. 145 185 211 168 203 228

 64b-2t2c-dot1q-l2xcbase-ndrpdr 

 1.  6.21       4.18 
2. 7.51 5.05

3. 22 39 55 22 41 54
4. 38 66 77 28 65 77
5. 78 97 113 81 99 112

 64b-4t4c-dot1q-l2xcbase-ndrpdr 

 1.  7.93       5.33 
2. 7.93 5.33

3. 22 38 54 22 27 46
4. 26 52 59 24 50 56
5. 51 63 74 51 64 78

10ge2p1x520-eth-l2bdbasemaclrn-iacl50sf-10kflows-ndrpdr

RFC2544: Packet throughput L2BD test cases with ACL

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.

  • [Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Intel-X520-DA2.

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.

  • [Ref] Applicable standard specifications: RFC2544.

 Test Name 

 Throughput: 
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)

One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)

 64b-1t1c-eth- 
l2bdbasemaclrn-iacl50sf-10kflows-ndrpdr

 1.  2.77       1.86 
2. 2.79 1.87

3. 25 34 87 26 36 96
4. 61 171 187 54 163 173
5. 122 175 206 123 166 209

 64b-2t2c-eth- 
l2bdbasemaclrn-iacl50sf-10kflows-ndrpdr

 1.  4.40       2.96 
2. 4.54 3.05

3. 25 35 98 25 33 46
4. 45 115 131 47 120 136
5. 130 142 152 131 139 148

 64b-4t4c-eth- 
l2bdbasemaclrn-iacl50sf-10kflows-ndrpdr

 1.  5.97       4.01 
2. 8.02 5.39

3. 25 60 76 26 56 77
4. 68 82 89 49 73 90
5. 87 106 116 82 98 107

10ge2p1x520-eth-l2bdbasemaclrn-iacl50sl-10kflows-ndrpdr

RFC2544: Packet throughput L2BD test cases with ACL

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.

  • [Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Intel-X520-DA2.

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.

  • [Ref] Applicable standard specifications: RFC2544.

 Test Name 

 Throughput: 
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)

One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)

 64b-1t1c-eth- 
l2bdbasemaclrn-iacl50sl-10kflows-ndrpdr

 1.  2.77       1.86 
2. 2.79 1.87

3. 25 41 86 25 68 113
4. 80 193 201 74 178 185
5. 122 199 231 118 176 191

 64b-2t2c-eth- 
l2bdbasemaclrn-iacl50sl-10kflows-ndrpdr

 1.  4.41       2.96 
2. 4.43 2.98

3. 25 64 130 25 34 123
4. 50 105 115 49 103 114
5. 69 128 148 57 73 113

 64b-4t4c-eth- 
l2bdbasemaclrn-iacl50sl-10kflows-ndrpdr

 1.  6.53       4.39 
2. 8.02 5.39

3. 26 56 74 26 39 74
4. 66 82 89 53 77 92
5. 91 109 120 85 102 112

10ge2p1x520-eth-l2bdbasemaclrn-macip-iacl50sl-10kflows-ndrpdr

RFC2544: Packet throughput L2BD test cases with ACL

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 for L2 switching of IPv4.

  • [Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required MACIP ACL rules are applied to input paths of both DUT1 interfaces. DUT1 and DUT2 are tested with Intel-X520-DA2.

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.

  • [Ref] Applicable standard specifications: RFC2544.

 Test Name 

 Throughput: 
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)

One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)

 64b-1t1c-eth-l2bdbasemaclrn- 
macip-iacl50sl-10kflows-ndrpdr

 1.  1.90       1.28 
2. 1.91 1.29

3. 24 39 92 25 68 112
4. 31 217 250 32 211 228
5. 140 249 281 135 241 276

 64b-2t2c-eth-l2bdbasemaclrn- 
macip-iacl50sl-10kflows-ndrpdr

 1.  3.38       2.27 
2. 3.41 2.29

3. 24 30 116 25 35 59
4. 31 132 149 46 151 168
5. 106 152 170 133 172 183

 64b-4t4c-eth-l2bdbasemaclrn- 
macip-iacl50sl-10kflows-ndrpdr

 1.  6.24       4.19 
2. 6.30 4.23

3. 25 54 63 25 63 73
4. 48 95 102 50 97 107
5. 95 116 127 97 119 137

10ge2p1x520-eth-l2bdbasemaclrn-ndrpdr

RFC2544: Pkt throughput L2BD test cases

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 for L2 switching of IPv4.

  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 bridge- domain and MAC learning enabled. DUT1 and DUT2 tested with Intel-X520-DA2.

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 254 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.

  • [Ref] Applicable standard specifications: RFC2544.

 Test Name 

 Throughput: 
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)

One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)

 64b-1t1c- 
eth-l2bdbasemaclrn-ndrpdr

 1.  5.08       3.41 
2. 5.13 3.45

3. 24 82 104 25 74 105
4. 49 94 103 49 99 107
5. 168 211 237 179 218 248

 64b-2t2c- 
eth-l2bdbasemaclrn-ndrpdr

 1.  6.93       4.66 
2. 7.07 4.75

3. 24 75 94 25 63 93
4. 53 86 95 44 88 96
5. 102 129 160 102 129 159

 64b-4t4c- 
eth-l2bdbasemaclrn-ndrpdr

 1.  7.94       5.34 
2. 7.98 5.37

3. 25 46 60 25 32 53
4. 35 62 70 26 30 35
5. 63 81 89 64 82 90

10ge2p1x520-eth-l2bdbasemaclrn-oacl50sf-10kflows-ndrpdr

RFC2544: Packet throughput L2BD test cases with ACL

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.

  • [Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Intel-X520-DA2.

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.

  • [Ref] Applicable standard specifications: RFC2544.

 Test Name 

 Throughput: 
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)

One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)

 64b-1t1c-eth- 
l2bdbasemaclrn-oacl50sf-10kflows-ndrpdr

 1.  2.67       1.79 
2. 2.70 1.81

3. 26 41 85 27 44 114
4. 89 178 203 86 181 192
5. 126 200 222 114 186 199

 64b-2t2c-eth- 
l2bdbasemaclrn-oacl50sf-10kflows-ndrpdr

 1.  4.24       2.85 
2. 4.26 2.87

3. 25 32 103 26 35 123
4. 84 119 131 34 128 135
5. 69 110 144 79 102 150

 64b-4t4c-eth- 
l2bdbasemaclrn-oacl50sf-10kflows-ndrpdr

 1.  6.54       4.39 
2. 8.03 5.39

3. 26 63 76 26 35 70
4. 70 84 92 52 85 94
5. 93 112 127 87 104 116

10ge2p1x520-eth-l2bdbasemaclrn-oacl50sl-10kflows-ndrpdr

RFC2544: Packet throughput L2BD test cases with ACL

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.

  • [Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Intel-X520-DA2.

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.

  • [Ref] Applicable standard specifications: RFC2544.

 Test Name 

 Throughput: 
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)

One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)

 64b-1t1c-eth- 
l2bdbasemaclrn-oacl50sl-10kflows-ndrpdr

 1.  2.66       1.78 
2. 2.68 1.80

3. 26 45 88 27 47 115
4. 85 110 190 86 183 188
5. 125 198 227 116 186 197

 64b-2t2c-eth- 
l2bdbasemaclrn-oacl50sl-10kflows-ndrpdr

 1.  4.27       2.87 
2. 4.27 2.87

3. 26 34 105 26 35 127
4. 78 118 130 54 126 135
5. 72 122 148 80 106 160

 64b-4t4c-eth- 
l2bdbasemaclrn-oacl50sl-10kflows-ndrpdr

 1.  6.68       4.49 
2. 8.04 5.40

3. 26 65 76 26 30 65
4. 71 84 91 38 80 93
5. 94 114 130 88 105 118

10ge2p1x520-eth-l2bdscale100kmaclrn-ndrpdr

RFC2544: Pkt throughput for L2BD test cases

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 for L2 switching of IPv4.

  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 bridge- domain and MAC learning enabled. DUT1 and DUT2 tested with Intel-X520-DA2.

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 50k flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses ranges are incremented as follows: port01_src ca:fe:00:00:00:00 - port01_src ca:fe:00:07:a1:1f, port01_dst fa:ce:00:00:00:00 - port01_dst fa:ce:00:07:a1:1f, port02_src fa:ce:00:00:00:00 - port02_src fa:ce:00:07:a1:1f, port02_dst ca:fe:00:00:00:00 - port02_dst ca:fe:00:07:a1:1f

  • [Ref] Applicable standard specifications: RFC2544.

 Test Name 

 Throughput: 
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)

One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)

 64b-1t1c- 
eth-l2bdscale100kmaclrn-ndrpdr

 1.  3.77       2.53 
2. 3.80 2.56

3. 24 87 112 24 95 116
4. 40 121 137 48 108 131
5. 157 233 275 164 240 280

 64b-2t2c- 
eth-l2bdscale100kmaclrn-ndrpdr

 1.  5.37       3.61 
2. 5.45 3.67

3. 24 64 88 25 67 86
4. 71 122 133 70 97 122
5. 129 165 201 131 168 205

 64b-4t4c- 
eth-l2bdscale100kmaclrn-ndrpdr

 1.  7.75       5.21 
2. 7.91 5.31

3. 24 26 43 25 57 68
4. 30 66 78 27 33 63
5. 85 102 116 81 101 124

10ge2p1x520-eth-l2bdscale10kmaclrn-ndrpdr

RFC2544: Pkt throughput for L2BD test cases

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 for L2 switching of IPv4.

  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 bridge- domain and MAC learning enabled. DUT1 and DUT2 tested with Intel-X520-DA2.

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 5k flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses ranges are incremented as follows: port01_src ca:fe:00:00:00:00 - port01_src ca:fe:00:07:a1:1f, port01_dst fa:ce:00:00:00:00 - port01_dst fa:ce:00:07:a1:1f, port02_src fa:ce:00:00:00:00 - port02_src fa:ce:00:07:a1:1f, port02_dst ca:fe:00:00:00:00 - port02_dst ca:fe:00:07:a1:1f

  • [Ref] Applicable standard specifications: RFC2544.

 Test Name 

 Throughput: 
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)

One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)

 64b-1t1c- 
eth-l2bdscale10kmaclrn-ndrpdr

 1.  4.05       2.72 
2. 4.11 2.76

3. 24 75 105 24 62 101
4. 75 125 134 76 125 132
5. 166 216 264 177 230 286

 64b-2t2c- 
eth-l2bdscale10kmaclrn-ndrpdr

 1.  5.58       3.75 
2. 5.66 3.80

3. 24 42 53 24 40 49
4. 42 99 111 56 110 120
5. 127 160 197 127 164 197

 64b-4t4c- 
eth-l2bdscale10kmaclrn-ndrpdr

 1.  7.91       5.31 
2. 7.99 5.37

3. 25 51 71 25 26 31
4. 35 67 81 26 30 33
5. 78 97 107 77 97 114

10ge2p1x520-eth-l2bdscale1mmaclrn-ndrpdr

RFC2544: Pkt throughput for L2BD test cases

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 for L2 switching of IPv4.

  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 bridge- domain and MAC learning enabled. DUT1 and DUT2 tested with Intel-X520-DA2.

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 500k flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses ranges are incremented as follows: port01_src ca:fe:00:00:00:00 - port01_src ca:fe:00:07:a1:1f, port01_dst fa:ce:00:00:00:00 - port01_dst fa:ce:00:07:a1:1f, port02_src fa:ce:00:00:00:00 - port02_src fa:ce:00:07:a1:1f, port02_dst ca:fe:00:00:00:00 - port02_dst ca:fe:00:07:a1:1f

  • [Ref] Applicable standard specifications: RFC2544.

 Test Name 

 Throughput: 
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)

One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)

 64b-1t1c- 
eth-l2bdscale1mmaclrn-ndrpdr

 1.  3.18       2.14 
2. 3.31 2.23

3. 24 70 102 24 67 115
4. 40 117 136 37 124 149
5. 140 322 411 145 337 430

 64b-2t2c- 
eth-l2bdscale1mmaclrn-ndrpdr

 1.  5.16       3.47 
2. 5.21 3.50

3. 25 113 157 25 103 125
4. 71 127 152 48 116 130
5. 166 268 342 136 169 202

 64b-4t4c- 
eth-l2bdscale1mmaclrn-ndrpdr

 1.  7.25       4.87 
2. 7.55 5.07

3. 25 43 66 25 47 61
4. 37 73 98 33 66 83
5. 100 129 158 87 106 119

10ge2p1x520-eth-l2patch-ndrpdr

RFC2544: Pkt throughput L2patch test cases

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 for L2 patch.

  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 patch DUT1 and DUT2 tested with Intel-X520-DA2.

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 254 flows per flow-group) with all packets containing Ethernet header,IPv4 header with static payload. MAC addresses are matching MAC addresses of the TG node interfaces.

  • [Ref] Applicable standard specifications: RFC2544.

 Test Name 

 Throughput: 
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)

One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)

 64b-1t1c-eth-l2patch-ndrpdr 

 1.  7.43       4.99 
2. 7.96 5.35

3. 18 33 57 19 33 55
4. 34 61 66 20 59 66
5. 106 138 156 115 143 162

 64b-2t2c-eth-l2patch-ndrpdr 

 1.  7.87       5.29 
2. 7.87 5.29

3. 18 22 48 18 20 49
4. 20 46 57 19 20 25
5. 54 71 87 52 70 88

 64b-4t4c-eth-l2patch-ndrpdr 

 1.  7.92       5.32 
2. 7.92 5.32

3. 18 35 45 19 23 44
4. 22 45 54 20 40 48
5. 45 60 79 43 60 80

10ge2p1x520-eth-l2xcbase-ndrpdr

RFC2544: Pkt throughput L2XC test cases

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 for L2 cross connect.

  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 cross- connect. DUT1 and DUT2 tested with Intel-X520-DA2.

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.

  • [Ref] Applicable standard specifications: RFC2544.

 Test Name 

 Throughput: 
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)

One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)

 64b-1t1c-eth-l2xcbase-ndrpdr 

 1.  6.00       4.03 
2. 6.15 4.13

3. 21 53 66 21 54 68
4. 48 84 89 45 78 89
5. 138 175 196 148 184 209

 64b-2t2c-eth-l2xcbase-ndrpdr 

 1.  7.49       5.03 
2. 7.88 5.29

3. 21 50 61 21 48 58
4. 23 53 60 22 34 57
5. 81 97 113 80 100 113

 64b-4t4c-eth-l2xcbase-ndrpdr 

 1.  7.45       5.01 
2. 7.95 5.34

3. 21 38 48 21 28 47
4. 31 54 60 22 25 29
5. 50 63 80 51 67 83