3n-hsw-vic1227
10ge2p1vic1227-dot1q-l2bdbasemaclrn-ndrpdr
RFC2544: Pkt throughput L2BD with IEEE 802.1Q test cases
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4 for L2 switching of IPv4. IEEE 802.1Q tagging is applied on link between DUT1 and DUT2.
[Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 bridge domain and MAC learning enabled. DUT1 and DUT2 are tested with Cisco-VIC-1227.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 254 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-1t1c-
dot1q-l2bdbasemaclrn-ndrpdr
|
1. 5.79 3.89
2. 8.31 5.58
3. 17 36 50 18 34 42
4. 46 56 64 42 52 62
5. 87 108 123 89 110 123
|
64b-2t2c-
dot1q-l2bdbasemaclrn-ndrpdr
|
1. 8.67 5.83
2. 16.78 11.27
3. 17 24 31 18 23 33
4. 25 34 42 26 36 43
5. 58 66 75 55 63 71
|
64b-4t4c-
dot1q-l2bdbasemaclrn-ndrpdr
|
1. 14.29 9.60
2. 17.54 11.79
3. 17 18 25 17 18 23
4. 20 29 32 19 26 31
5. 24 27 31 23 26 30
|
1518b-1t1c-
dot1q-l2bdbasemaclrn-ndrpdr
|
1. 1.61 19.85
2. 1.61 19.85
3. 22 23 26 22 23 25
4. 24 32 35 24 33 36
5. 26 33 37 27 34 37
|
1518b-2t2c-
dot1q-l2bdbasemaclrn-ndrpdr
|
1. 1.61 19.85
2. 1.61 19.85
3. 22 22 26 22 22 26
4. 22 23 27 21 22 25
5. 22 29 30 22 29 31
|
1518b-4t4c-
dot1q-l2bdbasemaclrn-ndrpdr
|
1. 1.25 15.38
2. 1.61 19.85
3. 22 22 28 22 23 28
4. 22 22 25 21 22 25
5. 21 28 29 21 28 29
|
imix-1t1c-
dot1q-l2bdbasemaclrn-ndrpdr
|
1. 0.67 2.01
2. 6.58 19.69
|
imix-2t2c-
dot1q-l2bdbasemaclrn-ndrpdr
|
1. 4.62 13.81
2. 6.58 19.69
|
imix-4t4c-
dot1q-l2bdbasemaclrn-ndrpdr
|
1. 4.76 14.23
2. 6.58 19.69
|
10ge2p1vic1227-dot1q-l2xcbase-ndrpdr
RFC2544: Pkt throughput L2XC with IEEE 802.1Q test cases
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4 for L2 cross connect. IEEE 802.1Q tagging is applied on link between DUT1 and DUT2.
[Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 cross- connect. DUT1 and DUT2 are tested with Cisco-VIC-1227.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 254 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-1t1c-dot1q-l2xcbase-ndrpdr
|
1. 6.13 4.12
2. 10.47 7.03
3. 16 21 29 17 25 34
4. 25 31 37 25 31 37
5. 70 85 97 75 91 103
|
64b-2t2c-dot1q-l2xcbase-ndrpdr
|
1. 14.01 9.41
2. 16.69 11.21
3. 17 22 28 17 21 28
4. 26 34 38 27 35 38
5. 30 38 44 29 35 41
|
64b-4t4c-dot1q-l2xcbase-ndrpdr
|
1. 12.68 8.52
2. 17.54 11.79
3. 17 19 22 17 19 21
4. 17 22 26 17 20 24
5. 17 22 25 17 21 24
|
1518b-1t1c-
dot1q-l2xcbase-ndrpdr
|
1. 1.61 19.75
2. 1.61 19.85
3. 22 22 27 22 22 28
4. 26 31 32 26 31 33
5. 24 32 35 24 31 35
|
1518b-2t2c-
dot1q-l2xcbase-ndrpdr
|
1. 1.54 18.97
2. 1.61 19.85
3. 22 22 23 22 22 23
4. 22 27 29 21 26 29
5. 22 29 31 22 25 29
|
1518b-4t4c-
dot1q-l2xcbase-ndrpdr
|
1. 1.28 15.77
2. 1.61 19.85
3. 22 23 28 22 23 28
4. 21 22 25 21 22 25
5. 21 27 29 21 28 29
|
imix-1t1c-
dot1q-l2xcbase-ndrpdr
|
1. 4.55 13.61
2. 6.58 19.69
|
imix-2t2c-
dot1q-l2xcbase-ndrpdr
|
1. 4.50 13.47
2. 6.58 19.69
|
imix-4t4c-
dot1q-l2xcbase-ndrpdr
|
1. 4.53 13.53
2. 6.58 19.69
|
10ge2p1vic1227-eth-l2bdbasemaclrn-iacl10sf-100flows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Cisco-VIC-1227.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100 flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-1t1c-eth-
l2bdbasemaclrn-iacl10sf-100flows-ndrpdr
|
1. 5.35 3.60
2. 5.41 3.63
3. 17 36 55 17 36 53
4. 42 67 97 19 68 77
5. 64 89 109 64 88 96
|
64b-2t2c-eth-
l2bdbasemaclrn-iacl10sf-100flows-ndrpdr
|
1. 9.10 6.11
2. 10.63 7.14
3. 17 45 62 18 48 59
4. 27 51 59 26 51 57
5. 54 68 79 52 65 77
|
64b-4t4c-eth-
l2bdbasemaclrn-iacl10sf-100flows-ndrpdr
|
1. 13.79 9.27
2. 16.54 11.11
3. 17 28 38 18 21 36
4. 31 38 43 30 38 43
5. 32 40 48 35 47 61
|
1518b-1t1c-eth-
l2bdbasemaclrn-iacl10sf-100flows-ndrpdr
|
1. 1.62 19.90
2. 1.62 19.90
3. 22 22 25 22 22 23
4. 22 29 32 22 28 31
5. 27 33 37 26 33 37
|
1518b-2t2c-eth-
l2bdbasemaclrn-iacl10sf-100flows-ndrpdr
|
1. 1.61 19.80
2. 1.62 19.90
3. 22 22 24 22 22 23
4. 22 25 28 22 24 28
5. 23 29 32 23 29 32
|
1518b-4t4c-eth-
l2bdbasemaclrn-iacl10sf-100flows-ndrpdr
|
1. 1.58 19.41
2. 1.62 19.90
3. 22 22 25 22 22 24
4. 22 25 27 22 23 26
5. 22 28 31 22 27 30
|
imix-1t1c-eth-
l2bdbasemaclrn-iacl10sf-100flows-ndrpdr
|
1. 5.05 15.10
2. 5.39 16.12
|
imix-2t2c-eth-
l2bdbasemaclrn-iacl10sf-100flows-ndrpdr
|
1. 4.98 14.89
2. 6.65 19.90
|
imix-4t4c-eth-
l2bdbasemaclrn-iacl10sf-100flows-ndrpdr
|
1. 4.60 13.75
2. 6.65 19.90
|
10ge2p1vic1227-eth-l2bdbasemaclrn-iacl10sf-100kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Cisco-VIC-1227.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-1t1c-eth-
l2bdbasemaclrn-iacl10sf-100kflows-ndrpdr
|
1. 5.34 3.59
2. 5.40 3.63
3. 17 45 62 17 46 67
4. 43 79 101 44 69 101
5. 68 100 122 74 97 104
|
64b-2t2c-eth-
l2bdbasemaclrn-iacl10sf-100kflows-ndrpdr
|
1. 9.42 6.33
2. 10.62 7.14
3. 17 38 56 17 35 56
4. 26 45 54 25 46 54
5. 40 49 56 43 52 58
|
64b-4t4c-eth-
l2bdbasemaclrn-iacl10sf-100kflows-ndrpdr
|
1. 13.81 9.28
2. 18.18 12.22
3. 17 23 33 18 20 31
4. 25 37 43 22 34 39
5. 40 50 70 35 45 54
|
1518b-1t1c-eth-
l2bdbasemaclrn-iacl10sf-100kflows-ndrpdr
|
1. 1.60 19.70
2. 1.62 19.90
3. 22 23 27 22 22 23
4. 25 30 35 23 28 33
5. 26 34 38 25 32 37
|
1518b-2t2c-eth-
l2bdbasemaclrn-iacl10sf-100kflows-ndrpdr
|
1. 1.61 19.80
2. 1.62 19.90
3. 22 23 27 22 23 27
4. 22 25 28 22 24 27
5. 22 30 32 23 30 32
|
1518b-4t4c-eth-
l2bdbasemaclrn-iacl10sf-100kflows-ndrpdr
|
1. 1.61 19.80
2. 1.62 19.90
3. 22 22 24 22 22 23
4. 22 24 27 22 23 26
5. 22 29 31 22 25 28
|
imix-1t1c-eth-
l2bdbasemaclrn-iacl10sf-100kflows-ndrpdr
|
1. 5.05 15.09
2. 5.39 16.11
|
imix-2t2c-eth-
l2bdbasemaclrn-iacl10sf-100kflows-ndrpdr
|
1. 5.00 14.97
2. 6.65 19.90
|
imix-4t4c-eth-
l2bdbasemaclrn-iacl10sf-100kflows-ndrpdr
|
1. 4.22 12.63
2. 6.65 19.90
|
10ge2p1vic1227-eth-l2bdbasemaclrn-iacl10sf-10kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Cisco-VIC-1227.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-1t1c-eth-
l2bdbasemaclrn-iacl10sf-10kflows-ndrpdr
|
1. 5.35 3.60
2. 5.41 3.63
3. 17 51 70 17 54 77
4. 27 72 86 35 61 82
5. 65 95 116 68 91 99
|
64b-2t2c-eth-
l2bdbasemaclrn-iacl10sf-10kflows-ndrpdr
|
1. 9.48 6.37
2. 10.64 7.15
3. 17 40 53 18 43 56
4. 32 47 55 30 44 53
5. 53 67 78 50 63 73
|
64b-4t4c-eth-
l2bdbasemaclrn-iacl10sf-10kflows-ndrpdr
|
1. 12.99 8.73
2. 17.62 11.84
3. 18 29 40 18 22 37
4. 29 38 43 27 37 42
5. 39 64 127 40 64 123
|
1518b-1t1c-eth-
l2bdbasemaclrn-iacl10sf-10kflows-ndrpdr
|
1. 1.49 18.37
2. 1.62 19.90
3. 22 22 25 22 22 24
4. 23 29 32 22 27 31
5. 27 34 38 25 32 37
|
1518b-2t2c-eth-
l2bdbasemaclrn-iacl10sf-10kflows-ndrpdr
|
1. 1.57 19.31
2. 1.62 19.90
3. 22 22 23 22 22 23
4. 22 26 28 22 26 28
5. 23 30 32 23 26 32
|
1518b-4t4c-eth-
l2bdbasemaclrn-iacl10sf-10kflows-ndrpdr
|
1. 1.59 19.60
2. 1.62 19.90
3. 22 23 26 22 23 26
4. 22 24 26 22 23 26
5. 22 29 32 21 25 28
|
imix-1t1c-eth-
l2bdbasemaclrn-iacl10sf-10kflows-ndrpdr
|
1. 4.66 13.94
2. 5.39 16.12
|
imix-2t2c-eth-
l2bdbasemaclrn-iacl10sf-10kflows-ndrpdr
|
1. 4.60 13.75
2. 6.65 19.90
|
imix-4t4c-eth-
l2bdbasemaclrn-iacl10sf-10kflows-ndrpdr
|
1. 4.81 14.38
2. 6.65 19.90
|
10ge2p1vic1227-eth-l2bdbasemaclrn-iacl10sl-100flows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Cisco-VIC-1227.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100 flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-1t1c-eth-
l2bdbasemaclrn-iacl10sl-100flows-ndrpdr
|
1. 5.31 3.57
2. 5.39 3.62
3. 17 46 75 17 59 74
4. 44 73 100 19 70 79
5. 65 103 128 70 94 102
|
64b-2t2c-eth-
l2bdbasemaclrn-iacl10sl-100flows-ndrpdr
|
1. 9.73 6.54
2. 10.65 7.16
3. 18 43 61 17 45 58
4. 32 56 64 32 58 62
5. 52 66 77 50 62 73
|
64b-4t4c-eth-
l2bdbasemaclrn-iacl10sl-100flows-ndrpdr
|
1. 14.46 9.72
2. 17.06 11.46
3. 18 23 32 18 19 27
4. 22 33 39 20 31 37
5. 34 51 79 33 43 57
|
1518b-1t1c-eth-
l2bdbasemaclrn-iacl10sl-100flows-ndrpdr
|
1. 1.62 19.90
2. 1.62 19.90
3. 22 22 25 22 22 25
4. 25 30 32 23 29 32
5. 27 34 38 25 32 37
|
1518b-2t2c-eth-
l2bdbasemaclrn-iacl10sl-100flows-ndrpdr
|
1. 1.59 19.60
2. 1.62 19.90
3. 22 22 24 22 22 23
4. 22 23 27 22 24 27
5. 22 29 32 22 30 32
|
1518b-4t4c-eth-
l2bdbasemaclrn-iacl10sl-100flows-ndrpdr
|
1. 1.59 19.60
2. 1.62 19.90
3. 22 23 26 22 23 26
4. 22 25 27 22 23 26
5. 22 28 31 22 28 31
|
imix-1t1c-eth-
l2bdbasemaclrn-iacl10sl-100flows-ndrpdr
|
1. 4.85 14.50
2. 5.41 16.19
|
imix-2t2c-eth-
l2bdbasemaclrn-iacl10sl-100flows-ndrpdr
|
1. 4.83 14.45
2. 6.65 19.90
|
imix-4t4c-eth-
l2bdbasemaclrn-iacl10sl-100flows-ndrpdr
|
1. 4.67 13.95
2. 6.65 19.90
|
10ge2p1vic1227-eth-l2bdbasemaclrn-iacl10sl-100kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Cisco-VIC-1227.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-1t1c-eth-
l2bdbasemaclrn-iacl10sl-100kflows-ndrpdr
|
1. 5.35 3.60
2. 5.41 3.63
3. 17 49 66 17 49 66
4. 39 57 86 19 58 64
5. 67 91 111 72 94 104
|
64b-2t2c-eth-
l2bdbasemaclrn-iacl10sl-100kflows-ndrpdr
|
1. 9.98 6.71
2. 10.60 7.12
3. 18 34 50 18 34 49
4. 33 57 66 33 57 62
5. 54 67 77 50 63 69
|
64b-4t4c-eth-
l2bdbasemaclrn-iacl10sl-100kflows-ndrpdr
|
1. 13.31 8.94
2. 17.26 11.60
3. 17 23 31 17 19 25
4. 25 35 40 24 34 38
5. 39 56 78 40 51 69
|
1518b-1t1c-eth-
l2bdbasemaclrn-iacl10sl-100kflows-ndrpdr
|
1. 1.62 19.90
2. 1.62 19.90
3. 22 22 26 22 22 24
4. 25 30 35 22 26 32
5. 27 33 37 25 33 37
|
1518b-2t2c-eth-
l2bdbasemaclrn-iacl10sl-100kflows-ndrpdr
|
1. 1.62 19.90
2. 1.62 19.90
3. 22 22 24 22 22 23
4. 22 26 28 22 25 28
5. 23 29 32 23 30 32
|
1518b-4t4c-eth-
l2bdbasemaclrn-iacl10sl-100kflows-ndrpdr
|
1. 1.62 19.90
2. 1.62 19.90
3. 22 23 25 22 23 25
4. 22 25 27 21 23 25
5. 22 28 31 22 28 31
|
imix-1t1c-eth-
l2bdbasemaclrn-iacl10sl-100kflows-ndrpdr
|
1. 5.20 15.54
2. 5.38 16.09
|
imix-2t2c-eth-
l2bdbasemaclrn-iacl10sl-100kflows-ndrpdr
|
1. 4.83 14.45
2. 6.65 19.90
|
imix-4t4c-eth-
l2bdbasemaclrn-iacl10sl-100kflows-ndrpdr
|
1. 4.20 12.57
2. 6.65 19.90
|
10ge2p1vic1227-eth-l2bdbasemaclrn-iacl10sl-10kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Cisco-VIC-1227.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-1t1c-eth-
l2bdbasemaclrn-iacl10sl-10kflows-ndrpdr
|
1. 5.35 3.59
2. 5.40 3.63
3. 17 36 49 17 34 51
4. 38 65 91 39 80 89
5. 65 93 111 74 96 104
|
64b-2t2c-eth-
l2bdbasemaclrn-iacl10sl-10kflows-ndrpdr
|
1. 9.12 6.13
2. 10.34 6.95
3. 17 53 63 17 50 60
4. 34 59 67 35 57 62
5. 50 62 68 51 63 67
|
64b-4t4c-eth-
l2bdbasemaclrn-iacl10sl-10kflows-ndrpdr
|
1. 13.74 9.24
2. 17.30 11.62
3. 17 30 38 18 20 27
4. 26 37 44 23 33 39
5. 37 59 91 33 42 50
|
1518b-1t1c-eth-
l2bdbasemaclrn-iacl10sl-10kflows-ndrpdr
|
1. 1.61 19.80
2. 1.62 19.90
3. 22 22 25 22 22 24
4. 24 29 32 22 28 31
5. 27 34 38 25 31 36
|
1518b-2t2c-eth-
l2bdbasemaclrn-iacl10sl-10kflows-ndrpdr
|
1. 1.62 19.90
2. 1.62 19.90
3. 22 22 24 22 22 23
4. 22 26 28 22 23 28
5. 23 29 32 23 30 32
|
1518b-4t4c-eth-
l2bdbasemaclrn-iacl10sl-10kflows-ndrpdr
|
1. 1.41 17.39
2. 1.62 19.90
3. 22 22 23 22 22 23
4. 22 25 27 21 22 25
5. 22 29 31 22 25 28
|
imix-1t1c-eth-
l2bdbasemaclrn-iacl10sl-10kflows-ndrpdr
|
1. 4.78 14.28
2. 5.39 16.11
|
imix-2t2c-eth-
l2bdbasemaclrn-iacl10sl-10kflows-ndrpdr
|
1. 4.26 12.75
2. 6.65 19.90
|
imix-4t4c-eth-
l2bdbasemaclrn-iacl10sl-10kflows-ndrpdr
|
1. 4.76 14.24
2. 6.65 19.90
|
10ge2p1vic1227-eth-l2bdbasemaclrn-iacl1sf-100flows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Cisco-VIC-1227.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100 flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-1t1c-eth-
l2bdbasemaclrn-iacl1sf-100flows-ndrpdr
|
1. 5.14 3.45
2. 5.21 3.50
3. 17 51 78 17 62 81
4. 28 47 65 30 50 72
5. 59 81 97 63 82 96
|
64b-2t2c-eth-
l2bdbasemaclrn-iacl1sf-100flows-ndrpdr
|
1. 9.42 6.33
2. 10.46 7.03
3. 17 23 29 17 22 29
4. 24 35 41 24 36 45
5. 39 47 53 45 54 60
|
64b-4t4c-eth-
l2bdbasemaclrn-iacl1sf-100flows-ndrpdr
|
1. 13.12 8.81
2. 17.79 11.96
3. 17 29 36 18 21 35
4. 26 35 40 25 35 39
5. 34 46 59 40 50 73
|
1518b-1t1c-eth-
l2bdbasemaclrn-iacl1sf-100flows-ndrpdr
|
1. 1.62 19.90
2. 1.62 19.90
3. 22 22 25 22 23 26
4. 25 30 32 24 29 32
5. 26 30 33 25 29 33
|
1518b-2t2c-eth-
l2bdbasemaclrn-iacl1sf-100flows-ndrpdr
|
1. 1.22 15.04
2. 1.62 19.90
3. 22 23 27 22 22 26
4. 22 26 30 22 23 27
5. 23 30 32 23 29 32
|
1518b-4t4c-eth-
l2bdbasemaclrn-iacl1sf-100flows-ndrpdr
|
1. 1.57 19.31
2. 1.62 19.90
3. 22 22 24 22 22 23
4. 22 25 27 21 22 26
5. 22 29 31 21 25 27
|
imix-1t1c-eth-
l2bdbasemaclrn-iacl1sf-100flows-ndrpdr
|
1. 4.88 14.60
2. 5.26 15.74
|
imix-2t2c-eth-
l2bdbasemaclrn-iacl1sf-100flows-ndrpdr
|
1. 4.64 13.88
2. 6.65 19.90
|
imix-4t4c-eth-
l2bdbasemaclrn-iacl1sf-100flows-ndrpdr
|
1. 4.64 13.89
2. 6.65 19.90
|
10ge2p1vic1227-eth-l2bdbasemaclrn-iacl1sf-100kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Cisco-VIC-1227.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-1t1c-eth-
l2bdbasemaclrn-iacl1sf-100kflows-ndrpdr
|
1. 5.19 3.49
2. 5.25 3.53
3. 17 69 95 17 75 93
4. 22 50 65 22 53 74
5. 58 88 108 60 90 106
|
64b-2t2c-eth-
l2bdbasemaclrn-iacl1sf-100kflows-ndrpdr
|
1. 9.65 6.49
2. 10.67 7.17
3. 17 31 47 18 34 46
4. 27 42 51 25 39 47
5. 50 64 72 49 62 70
|
64b-4t4c-eth-
l2bdbasemaclrn-iacl1sf-100kflows-ndrpdr
|
1. 13.23 8.89
2. 17.86 12.00
3. 18 25 34 18 22 33
4. 25 35 40 23 35 39
5. 35 51 59 37 48 65
|
1518b-1t1c-eth-
l2bdbasemaclrn-iacl1sf-100kflows-ndrpdr
|
1. 1.59 19.60
2. 1.62 19.90
3. 22 23 30 22 23 28
4. 26 30 34 24 29 33
5. 26 34 38 25 32 36
|
1518b-2t2c-eth-
l2bdbasemaclrn-iacl1sf-100kflows-ndrpdr
|
1. 1.59 19.60
2. 1.62 19.90
3. 22 22 26 22 22 23
4. 22 28 31 21 25 31
5. 23 29 32 23 28 32
|
1518b-4t4c-eth-
l2bdbasemaclrn-iacl1sf-100kflows-ndrpdr
|
1. 1.50 18.46
2. 1.62 19.90
3. 22 22 23 22 22 23
4. 22 25 28 21 24 29
5. 22 28 30 22 28 31
|
imix-1t1c-eth-
l2bdbasemaclrn-iacl1sf-100kflows-ndrpdr
|
1. 5.03 15.03
2. 5.23 15.65
|
imix-2t2c-eth-
l2bdbasemaclrn-iacl1sf-100kflows-ndrpdr
|
1. 4.64 13.88
2. 6.65 19.90
|
imix-4t4c-eth-
l2bdbasemaclrn-iacl1sf-100kflows-ndrpdr
|
1. 4.69 14.03
2. 6.65 19.90
|
10ge2p1vic1227-eth-l2bdbasemaclrn-iacl1sf-10kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Cisco-VIC-1227.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-1t1c-eth-
l2bdbasemaclrn-iacl1sf-10kflows-ndrpdr
|
1. 5.15 3.46
2. 5.23 3.51
3. 17 40 80 17 54 83
4. 26 75 90 21 80 94
5. 67 97 112 76 96 106
|
64b-2t2c-eth-
l2bdbasemaclrn-iacl1sf-10kflows-ndrpdr
|
1. 9.79 6.58
2. 10.76 7.23
3. 17 30 47 17 29 48
4. 32 45 54 24 52 56
5. 51 62 70 54 66 76
|
64b-4t4c-eth-
l2bdbasemaclrn-iacl1sf-10kflows-ndrpdr
|
1. 13.18 8.86
2. 17.09 11.49
3. 17 22 32 18 19 27
4. 25 36 41 24 35 40
5. 33 42 51 37 58 177
|
1518b-1t1c-eth-
l2bdbasemaclrn-iacl1sf-10kflows-ndrpdr
|
1. 1.58 19.41
2. 1.62 19.90
3. 22 22 25 22 22 24
4. 22 29 32 22 27 31
5. 27 34 38 25 30 36
|
1518b-2t2c-eth-
l2bdbasemaclrn-iacl1sf-10kflows-ndrpdr
|
1. 1.60 19.70
2. 1.62 19.90
3. 22 22 24 22 22 24
4. 22 28 31 22 24 31
5. 23 29 32 22 29 32
|
1518b-4t4c-eth-
l2bdbasemaclrn-iacl1sf-10kflows-ndrpdr
|
1. 1.59 19.60
2. 1.62 19.90
3. 22 22 24 22 23 24
4. 22 27 29 21 25 29
5. 21 25 30 21 25 28
|
imix-1t1c-eth-
l2bdbasemaclrn-iacl1sf-10kflows-ndrpdr
|
1. 4.91 14.68
2. 5.21 15.59
|
imix-2t2c-eth-
l2bdbasemaclrn-iacl1sf-10kflows-ndrpdr
|
1. 4.76 14.24
2. 6.65 19.90
|
imix-4t4c-eth-
l2bdbasemaclrn-iacl1sf-10kflows-ndrpdr
|
1. 4.60 13.75
2. 6.65 19.90
|
10ge2p1vic1227-eth-l2bdbasemaclrn-iacl1sl-100flows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Cisco-VIC-1227.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100 flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-1t1c-eth-
l2bdbasemaclrn-iacl1sl-100flows-ndrpdr
|
1. 5.16 3.47
2. 5.24 3.52
3. 17 40 74 17 48 81
4. 24 63 79 21 71 85
5. 68 104 128 87 103 116
|
64b-2t2c-eth-
l2bdbasemaclrn-iacl1sl-100flows-ndrpdr
|
1. 9.63 6.47
2. 10.64 7.15
3. 17 23 32 17 25 38
4. 26 43 51 24 44 53
5. 44 55 64 47 59 68
|
64b-4t4c-eth-
l2bdbasemaclrn-iacl1sl-100flows-ndrpdr
|
1. 13.32 8.95
2. 17.72 11.91
3. 18 24 33 18 22 29
4. 20 29 33 20 29 33
5. 33 44 57 40 85 191
|
1518b-1t1c-eth-
l2bdbasemaclrn-iacl1sl-100flows-ndrpdr
|
1. 1.58 19.41
2. 1.62 19.90
3. 22 24 30 22 23 28
4. 22 29 32 22 28 31
5. 27 33 37 25 33 37
|
1518b-2t2c-eth-
l2bdbasemaclrn-iacl1sl-100flows-ndrpdr
|
1. 1.46 18.01
2. 1.62 19.90
3. 22 23 27 22 23 27
4. 22 28 31 22 25 31
5. 23 30 32 23 29 32
|
1518b-4t4c-eth-
l2bdbasemaclrn-iacl1sl-100flows-ndrpdr
|
1. 1.50 18.46
2. 1.62 19.90
3. 22 23 26 22 23 26
4. 22 27 30 21 25 29
5. 21 28 30 21 25 30
|
imix-1t1c-eth-
l2bdbasemaclrn-iacl1sl-100flows-ndrpdr
|
1. 4.99 14.91
2. 5.22 15.60
|
imix-2t2c-eth-
l2bdbasemaclrn-iacl1sl-100flows-ndrpdr
|
1. 4.78 14.31
2. 6.65 19.90
|
imix-4t4c-eth-
l2bdbasemaclrn-iacl1sl-100flows-ndrpdr
|
1. 4.69 14.03
2. 6.65 19.90
|
10ge2p1vic1227-eth-l2bdbasemaclrn-iacl1sl-100kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Cisco-VIC-1227.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-1t1c-eth-
l2bdbasemaclrn-iacl1sl-100kflows-ndrpdr
|
1. 5.20 3.50
2. 5.26 3.53
3. 17 42 60 17 42 57
4. 39 69 83 31 72 86
5. 69 99 122 79 99 108
|
64b-2t2c-eth-
l2bdbasemaclrn-iacl1sl-100kflows-ndrpdr
|
1. 9.51 6.39
2. 10.67 7.17
3. 17 30 47 17 34 47
4. 24 42 50 24 44 52
5. 37 46 53 42 52 59
|
64b-4t4c-eth-
l2bdbasemaclrn-iacl1sl-100kflows-ndrpdr
|
1. 13.26 8.91
2. 17.72 11.91
3. 17 21 24 17 19 24
4. 19 25 31 19 24 31
5. 33 43 52 39 79 185
|
1518b-1t1c-eth-
l2bdbasemaclrn-iacl1sl-100kflows-ndrpdr
|
1. 1.61 19.80
2. 1.62 19.90
3. 22 24 31 22 22 27
4. 24 28 32 22 27 31
5. 26 31 35 25 30 36
|
1518b-2t2c-eth-
l2bdbasemaclrn-iacl1sl-100kflows-ndrpdr
|
1. 1.59 19.51
2. 1.62 19.90
3. 22 23 26 22 24 26
4. 22 28 31 22 28 31
5. 22 29 31 22 25 30
|
1518b-4t4c-eth-
l2bdbasemaclrn-iacl1sl-100kflows-ndrpdr
|
1. 1.48 18.19
2. 1.62 19.90
3. 22 22 23 22 22 23
4. 22 26 29 22 26 29
5. 22 27 30 21 25 30
|
imix-1t1c-eth-
l2bdbasemaclrn-iacl1sl-100kflows-ndrpdr
|
1. 4.85 14.50
2. 5.23 15.63
|
imix-2t2c-eth-
l2bdbasemaclrn-iacl1sl-100kflows-ndrpdr
|
1. 4.76 14.23
2. 6.65 19.90
|
imix-4t4c-eth-
l2bdbasemaclrn-iacl1sl-100kflows-ndrpdr
|
1. 4.71 14.09
2. 6.65 19.90
|
10ge2p1vic1227-eth-l2bdbasemaclrn-iacl1sl-10kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Cisco-VIC-1227.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-1t1c-eth-
l2bdbasemaclrn-iacl1sl-10kflows-ndrpdr
|
1. 5.20 3.49
2. 5.25 3.53
3. 17 46 60 17 48 63
4. 33 59 81 34 78 89
5. 63 86 101 67 86 97
|
64b-2t2c-eth-
l2bdbasemaclrn-iacl1sl-10kflows-ndrpdr
|
1. 9.69 6.51
2. 10.61 7.13
3. 17 27 40 17 31 44
4. 27 41 49 21 41 46
5. 42 56 66 46 59 69
|
64b-4t4c-eth-
l2bdbasemaclrn-iacl1sl-10kflows-ndrpdr
|
1. 13.40 9.00
2. 18.09 12.16
3. 17 21 26 18 20 26
4. 19 24 30 18 23 30
5. 33 46 60 44 92 164
|
1518b-1t1c-eth-
l2bdbasemaclrn-iacl1sl-10kflows-ndrpdr
|
1. 1.54 18.93
2. 1.62 19.90
3. 22 22 27 22 22 25
4. 24 30 33 22 26 31
5. 27 34 38 25 32 36
|
1518b-2t2c-eth-
l2bdbasemaclrn-iacl1sl-10kflows-ndrpdr
|
1. 1.62 19.90
2. 1.62 19.90
3. 22 23 25 22 23 25
4. 22 25 30 22 25 27
5. 23 30 33 23 27 33
|
1518b-4t4c-eth-
l2bdbasemaclrn-iacl1sl-10kflows-ndrpdr
|
1. 1.61 19.80
2. 1.62 19.90
3. 22 22 24 22 22 23
4. 22 26 27 21 23 26
5. 22 28 30 22 28 30
|
imix-1t1c-eth-
l2bdbasemaclrn-iacl1sl-10kflows-ndrpdr
|
1. 4.60 13.75
2. 5.26 15.73
|
imix-2t2c-eth-
l2bdbasemaclrn-iacl1sl-10kflows-ndrpdr
|
1. 4.46 13.34
2. 6.65 19.90
|
imix-4t4c-eth-
l2bdbasemaclrn-iacl1sl-10kflows-ndrpdr
|
1. 4.55 13.61
2. 6.65 19.90
|
10ge2p1vic1227-eth-l2bdbasemaclrn-iacl50sf-100flows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Cisco-VIC-1227.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100 flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-1t1c-eth-
l2bdbasemaclrn-iacl50sf-100flows-ndrpdr
|
1. 5.24 3.52
2. 5.26 3.54
3. 17 30 44 17 32 42
4. 22 45 61 23 52 67
5. 56 75 90 58 74 87
|
64b-2t2c-eth-
l2bdbasemaclrn-iacl50sf-100flows-ndrpdr
|
1. 9.43 6.33
2. 10.68 7.18
3. 17 21 27 18 23 34
4. 26 43 52 33 49 55
5. 43 54 62 48 60 70
|
64b-4t4c-eth-
l2bdbasemaclrn-iacl50sf-100flows-ndrpdr
|
1. 13.39 9.00
2. 18.17 12.21
3. 17 22 34 17 19 30
4. 25 35 41 23 34 39
5. 39 51 64 46 91 152
|
1518b-1t1c-eth-
l2bdbasemaclrn-iacl50sf-100flows-ndrpdr
|
1. 1.61 19.80
2. 1.62 19.90
3. 22 25 30 22 23 29
4. 22 29 32 22 27 32
5. 27 34 38 26 32 37
|
1518b-2t2c-eth-
l2bdbasemaclrn-iacl50sf-100flows-ndrpdr
|
1. 1.58 19.41
2. 1.62 19.90
3. 22 22 24 22 22 23
4. 22 26 28 22 25 27
5. 23 30 33 23 26 32
|
1518b-4t4c-eth-
l2bdbasemaclrn-iacl50sf-100flows-ndrpdr
|
1. 1.53 18.83
2. 1.62 19.90
3. 22 23 27 22 23 27
4. 22 23 26 22 23 26
5. 22 29 31 22 25 27
|
imix-1t1c-eth-
l2bdbasemaclrn-iacl50sf-100flows-ndrpdr
|
1. 4.87 14.56
2. 5.27 15.77
|
imix-2t2c-eth-
l2bdbasemaclrn-iacl50sf-100flows-ndrpdr
|
1. 4.98 14.89
2. 6.65 19.90
|
imix-4t4c-eth-
l2bdbasemaclrn-iacl50sf-100flows-ndrpdr
|
1. 4.53 13.54
2. 6.65 19.90
|
10ge2p1vic1227-eth-l2bdbasemaclrn-iacl50sf-100kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Cisco-VIC-1227.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-1t1c-eth-
l2bdbasemaclrn-iacl50sf-100kflows-ndrpdr
|
1. 5.21 3.50
2. 5.26 3.54
3. 17 49 79 17 66 80
4. 39 72 90 22 79 90
5. 69 102 122 79 97 109
|
64b-2t2c-eth-
l2bdbasemaclrn-iacl50sf-100kflows-ndrpdr
|
1. 9.37 6.30
2. 10.62 7.14
3. 18 39 54 17 40 56
4. 34 50 59 33 49 58
5. 51 64 75 53 66 77
|
64b-4t4c-eth-
l2bdbasemaclrn-iacl50sf-100kflows-ndrpdr
|
1. 12.82 8.61
2. 17.74 11.92
3. 17 29 37 18 27 37
4. 27 36 41 27 37 42
5. 36 46 59 49 120 197
|
1518b-1t1c-eth-
l2bdbasemaclrn-iacl50sf-100kflows-ndrpdr
|
1. 1.62 19.90
2. 1.62 19.90
3. 22 23 29 22 22 26
4. 23 30 33 22 27 31
5. 27 33 37 26 33 37
|
1518b-2t2c-eth-
l2bdbasemaclrn-iacl50sf-100kflows-ndrpdr
|
1. 1.62 19.90
2. 1.62 19.90
3. 22 23 27 22 23 26
4. 22 27 29 22 24 27
5. 23 30 32 23 30 32
|
1518b-4t4c-eth-
l2bdbasemaclrn-iacl50sf-100kflows-ndrpdr
|
1. 1.49 18.28
2. 1.62 19.90
3. 22 22 23 22 22 23
4. 22 24 26 22 24 26
5. 22 29 31 22 25 27
|
imix-1t1c-eth-
l2bdbasemaclrn-iacl50sf-100kflows-ndrpdr
|
1. 5.13 15.34
2. 5.26 15.73
|
imix-2t2c-eth-
l2bdbasemaclrn-iacl50sf-100kflows-ndrpdr
|
1. 4.60 13.75
2. 6.65 19.90
|
imix-4t4c-eth-
l2bdbasemaclrn-iacl50sf-100kflows-ndrpdr
|
1. 4.67 13.95
2. 6.65 19.90
|
10ge2p1vic1227-eth-l2bdbasemaclrn-iacl50sf-10kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Cisco-VIC-1227.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-1t1c-eth-
l2bdbasemaclrn-iacl50sf-10kflows-ndrpdr
|
1. 5.26 3.53
2. 5.29 3.55
3. 17 72 100 17 79 96
4. 43 72 94 27 78 99
5. 70 105 125 83 100 107
|
64b-2t2c-eth-
l2bdbasemaclrn-iacl50sf-10kflows-ndrpdr
|
1. 9.61 6.46
2. 10.73 7.21
3. 17 33 49 18 24 49
4. 27 54 62 28 54 59
5. 45 55 62 46 57 63
|
64b-4t4c-eth-
l2bdbasemaclrn-iacl50sf-10kflows-ndrpdr
|
1. 13.35 8.97
2. 17.75 11.93
3. 17 31 39 18 22 38
4. 28 38 43 25 37 42
5. 38 59 90 48 107 170
|
1518b-1t1c-eth-
l2bdbasemaclrn-iacl50sf-10kflows-ndrpdr
|
1. 1.58 19.41
2. 1.62 19.90
3. 22 22 27 22 22 25
4. 22 29 33 22 26 31
5. 27 33 37 26 33 37
|
1518b-2t2c-eth-
l2bdbasemaclrn-iacl50sf-10kflows-ndrpdr
|
1. 1.55 19.02
2. 1.62 19.90
3. 22 22 23 22 22 23
4. 22 26 28 22 23 27
5. 22 30 32 23 30 32
|
1518b-4t4c-eth-
l2bdbasemaclrn-iacl50sf-10kflows-ndrpdr
|
1. 1.45 17.83
2. 1.62 19.90
3. 22 22 24 22 22 23
4. 22 24 27 22 23 26
5. 22 28 30 22 27 30
|
imix-1t1c-eth-
l2bdbasemaclrn-iacl50sf-10kflows-ndrpdr
|
1. 5.00 14.95
2. 5.28 15.80
|
imix-2t2c-eth-
l2bdbasemaclrn-iacl50sf-10kflows-ndrpdr
|
1. 4.69 14.02
2. 6.65 19.90
|
imix-4t4c-eth-
l2bdbasemaclrn-iacl50sf-10kflows-ndrpdr
|
1. 4.67 13.95
2. 6.65 19.90
|
10ge2p1vic1227-eth-l2bdbasemaclrn-iacl50sl-100flows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Cisco-VIC-1227.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100 flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-1t1c-eth-
l2bdbasemaclrn-iacl50sl-100flows-ndrpdr
|
1. 5.19 3.49
2. 5.27 3.54
3. 17 55 92 17 73 91
4. 44 70 92 44 75 93
5. 64 90 112 68 90 100
|
64b-2t2c-eth-
l2bdbasemaclrn-iacl50sl-100flows-ndrpdr
|
1. 9.67 6.50
2. 10.74 7.22
3. 18 39 55 18 38 55
4. 35 52 59 23 51 57
5. 52 65 75 53 66 84
|
64b-4t4c-eth-
l2bdbasemaclrn-iacl50sl-100flows-ndrpdr
|
1. 13.20 8.87
2. 17.39 11.68
3. 17 26 35 18 18 25
4. 28 37 43 24 36 42
5. 34 44 51 41 77 166
|
1518b-1t1c-eth-
l2bdbasemaclrn-iacl50sl-100flows-ndrpdr
|
1. 1.59 19.51
2. 1.62 19.90
3. 22 22 25 22 22 23
4. 25 30 32 24 29 32
5. 27 34 38 25 31 36
|
1518b-2t2c-eth-
l2bdbasemaclrn-iacl50sl-100flows-ndrpdr
|
1. 1.45 17.83
2. 1.62 19.90
3. 22 23 27 22 22 26
4. 22 27 28 22 26 27
5. 23 30 33 23 26 32
|
1518b-4t4c-eth-
l2bdbasemaclrn-iacl50sl-100flows-ndrpdr
|
1. 1.58 19.41
2. 1.62 19.90
3. 22 22 26 22 22 25
4. 22 25 27 21 23 25
5. 22 29 31 22 25 27
|
imix-1t1c-eth-
l2bdbasemaclrn-iacl50sl-100flows-ndrpdr
|
1. 4.97 14.87
2. 5.28 15.79
|
imix-2t2c-eth-
l2bdbasemaclrn-iacl50sl-100flows-ndrpdr
|
1. 4.86 14.52
2. 6.65 19.90
|
imix-4t4c-eth-
l2bdbasemaclrn-iacl50sl-100flows-ndrpdr
|
1. 4.51 13.48
2. 6.65 19.90
|
10ge2p1vic1227-eth-l2bdbasemaclrn-iacl50sl-100kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Cisco-VIC-1227.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-1t1c-eth-
l2bdbasemaclrn-iacl50sl-100kflows-ndrpdr
|
1. 5.20 3.50
2. 5.26 3.53
3. 16 75 96 17 80 99
4. 33 72 87 23 81 90
5. 73 108 126 83 100 112
|
64b-2t2c-eth-
l2bdbasemaclrn-iacl50sl-100kflows-ndrpdr
|
1. 9.84 6.61
2. 10.66 7.16
3. 17 39 56 17 46 56
4. 31 55 64 30 57 61
5. 52 65 77 52 65 77
|
64b-4t4c-eth-
l2bdbasemaclrn-iacl50sl-100kflows-ndrpdr
|
1. 13.32 8.95
2. 18.07 12.14
3. 17 23 33 18 23 36
4. 27 37 43 24 36 40
5. 41 62 111 43 59 83
|
1518b-1t1c-eth-
l2bdbasemaclrn-iacl50sl-100kflows-ndrpdr
|
1. 1.56 19.21
2. 1.62 19.90
3. 22 22 27 22 22 25
4. 22 30 33 22 27 32
5. 27 34 38 26 32 36
|
1518b-2t2c-eth-
l2bdbasemaclrn-iacl50sl-100kflows-ndrpdr
|
1. 1.51 18.55
2. 1.62 19.90
3. 22 22 23 22 22 23
4. 22 26 28 22 26 28
5. 22 25 30 22 26 32
|
1518b-4t4c-eth-
l2bdbasemaclrn-iacl50sl-100kflows-ndrpdr
|
1. 1.62 19.90
2. 1.62 19.90
3. 22 23 27 22 23 27
4. 22 24 26 22 23 26
5. 22 29 31 22 25 27
|
imix-1t1c-eth-
l2bdbasemaclrn-iacl50sl-100kflows-ndrpdr
|
1. 5.09 15.21
2. 5.27 15.75
|
imix-2t2c-eth-
l2bdbasemaclrn-iacl50sl-100kflows-ndrpdr
|
1. 4.67 13.96
2. 6.65 19.90
|
imix-4t4c-eth-
l2bdbasemaclrn-iacl50sl-100kflows-ndrpdr
|
1. 4.60 13.75
2. 6.65 19.90
|
10ge2p1vic1227-eth-l2bdbasemaclrn-iacl50sl-10kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Cisco-VIC-1227.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-1t1c-eth-
l2bdbasemaclrn-iacl50sl-10kflows-ndrpdr
|
1. 5.18 3.48
2. 5.29 3.55
3. 17 52 70 17 55 69
4. 34 59 79 35 71 87
5. 68 97 119 71 93 101
|
64b-2t2c-eth-
l2bdbasemaclrn-iacl50sl-10kflows-ndrpdr
|
1. 9.67 6.50
2. 10.74 7.22
3. 18 29 43 18 28 44
4. 38 54 63 26 50 58
5. 48 60 67 51 64 76
|
64b-4t4c-eth-
l2bdbasemaclrn-iacl50sl-10kflows-ndrpdr
|
1. 14.66 9.85
2. 18.18 12.22
3. 17 27 36 18 20 35
4. 26 36 40 24 35 40
5. 38 48 61 44 59 83
|
1518b-1t1c-eth-
l2bdbasemaclrn-iacl50sl-10kflows-ndrpdr
|
1. 1.62 19.90
2. 1.62 19.90
3. 22 23 24 22 23 25
4. 22 31 35 22 28 31
5. 26 31 36 25 29 35
|
1518b-2t2c-eth-
l2bdbasemaclrn-iacl50sl-10kflows-ndrpdr
|
1. 1.58 19.41
2. 1.62 19.90
3. 22 22 23 22 22 23
4. 22 23 26 22 24 26
5. 23 27 29 22 27 29
|
1518b-4t4c-eth-
l2bdbasemaclrn-iacl50sl-10kflows-ndrpdr
|
1. 1.46 18.01
2. 1.62 19.90
3. 22 22 23 22 22 23
4. 22 25 27 22 25 27
5. 21 25 27 21 25 27
|
imix-1t1c-eth-
l2bdbasemaclrn-iacl50sl-10kflows-ndrpdr
|
1. 5.18 15.51
2. 5.26 15.74
|
imix-2t2c-eth-
l2bdbasemaclrn-iacl50sl-10kflows-ndrpdr
|
1. 4.78 14.31
2. 6.65 19.90
|
imix-4t4c-eth-
l2bdbasemaclrn-iacl50sl-10kflows-ndrpdr
|
1. 4.62 13.82
2. 6.65 19.90
|
10ge2p1vic1227-eth-l2bdbasemaclrn-macip-iacl10sl-100flows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4 for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required MACIP ACL rules are applied to input paths of both DUT1 interfaces. DUT1 and DUT2 are tested with 2p10GE NIC X520 Niantic by Intel.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-1t1c-eth-l2bdbasemaclrn-
macip-iacl10sl-100flows-ndrpdr
|
1. 3.79 2.55
2. 3.79 2.55
3. 17 30 72 17 28 95
4. 24 77 98 25 82 100
5. 61 112 132 64 115 128
|
64b-2t2c-eth-l2bdbasemaclrn-
macip-iacl10sl-100flows-ndrpdr
|
1. 6.84 4.60
2. 7.23 4.86
3. 17 27 37 17 23 36
4. 23 51 62 23 54 65
5. 37 57 65 46 66 79
|
64b-4t4c-eth-l2bdbasemaclrn-
macip-iacl10sl-100flows-ndrpdr
|
1. 12.66 8.51
2. 13.85 9.31
3. 17 36 42 18 36 43
4. 28 43 50 25 43 48
5. 34 42 50 42 52 60
|
1518b-1t1c-eth-l2bdbasemaclrn-
macip-iacl10sl-100flows-ndrpdr
|
1. 1.62 19.90
2. 1.62 19.90
3. 22 22 24 22 23 25
4. 26 31 34 24 30 33
5. 28 35 38 27 35 39
|
1518b-2t2c-eth-l2bdbasemaclrn-
macip-iacl10sl-100flows-ndrpdr
|
1. 1.59 19.60
2. 1.62 19.90
3. 22 22 26 22 22 25
4. 22 25 28 22 24 28
5. 23 30 32 23 29 32
|
1518b-4t4c-eth-l2bdbasemaclrn-
macip-iacl10sl-100flows-ndrpdr
|
1. 1.60 19.70
2. 1.62 19.90
3. 22 22 23 22 23 23
4. 22 23 28 21 23 28
5. 21 28 33 21 25 29
|
imix-1t1c-eth-l2bdbasemaclrn-
macip-iacl10sl-100flows-ndrpdr
|
1. 3.65 10.92
2. 3.65 10.92
|
imix-2t2c-eth-l2bdbasemaclrn-
macip-iacl10sl-100flows-ndrpdr
|
1. 4.95 14.82
2. 6.65 19.90
|
imix-4t4c-eth-l2bdbasemaclrn-
macip-iacl10sl-100flows-ndrpdr
|
1. 4.78 14.31
2. 6.65 19.90
|
10ge2p1vic1227-eth-l2bdbasemaclrn-macip-iacl10sl-100kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4 for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required MACIP ACL rules are applied to input paths of both DUT1 interfaces. DUT1 and DUT2 are tested with 2p10GE NIC X520 Niantic by Intel.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100k flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-1t1c-eth-l2bdbasemaclrn-
macip-iacl10sl-100kflows-ndrpdr
|
1. 3.52 2.36
2. 3.59 2.41
3. 17 54 111 17 51 106
4. 31 100 135 32 123 136
5. 70 127 154 79 133 146
|
64b-2t2c-eth-l2bdbasemaclrn-
macip-iacl10sl-100kflows-ndrpdr
|
1. 6.57 4.41
2. 6.68 4.49
3. 17 28 42 17 18 23
4. 23 56 69 22 57 70
5. 44 67 77 51 72 89
|
64b-4t4c-eth-l2bdbasemaclrn-
macip-iacl10sl-100kflows-ndrpdr
|
1. 12.09 8.12
2. 12.33 8.29
3. 17 21 31 17 19 24
4. 23 32 38 21 32 37
5. 43 59 77 41 56 73
|
1518b-1t1c-eth-l2bdbasemaclrn-
macip-iacl10sl-100kflows-ndrpdr
|
1. 1.62 19.90
2. 1.62 19.90
3. 22 29 32 22 27 31
4. 22 31 34 22 29 35
5. 28 35 39 27 35 39
|
1518b-2t2c-eth-l2bdbasemaclrn-
macip-iacl10sl-100kflows-ndrpdr
|
1. 1.61 19.80
2. 1.62 19.90
3. 22 23 23 22 23 23
4. 22 26 29 22 25 29
5. 23 30 32 23 30 32
|
1518b-4t4c-eth-l2bdbasemaclrn-
macip-iacl10sl-100kflows-ndrpdr
|
1. 1.62 19.90
2. 1.62 19.90
3. 22 23 26 22 23 26
4. 22 24 27 21 23 25
5. 22 29 31 21 25 27
|
imix-1t1c-eth-l2bdbasemaclrn-
macip-iacl10sl-100kflows-ndrpdr
|
1. 3.32 9.93
2. 3.44 10.28
|
imix-2t2c-eth-l2bdbasemaclrn-
macip-iacl10sl-100kflows-ndrpdr
|
1. 4.98 14.88
2. 6.45 19.30
|
imix-4t4c-eth-l2bdbasemaclrn-
macip-iacl10sl-100kflows-ndrpdr
|
1. 4.67 13.95
2. 6.65 19.90
|
10ge2p1vic1227-eth-l2bdbasemaclrn-macip-iacl10sl-10kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4 for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required MACIP ACL rules are applied to input paths of both DUT1 interfaces. DUT1 and DUT2 are tested with 2p10GE NIC X520 Niantic by Intel.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-1t1c-eth-l2bdbasemaclrn-
macip-iacl10sl-10kflows-ndrpdr
|
1. 3.71 2.49
2. 3.73 2.51
3. 17 45 93 17 55 97
4. 19 82 113 20 94 114
5. 56 112 135 57 114 128
|
64b-2t2c-eth-l2bdbasemaclrn-
macip-iacl10sl-10kflows-ndrpdr
|
1. 6.64 4.47
2. 6.75 4.53
3. 18 31 58 18 30 58
4. 23 48 61 23 47 61
5. 44 59 67 46 68 82
|
64b-4t4c-eth-l2bdbasemaclrn-
macip-iacl10sl-10kflows-ndrpdr
|
1. 11.81 7.94
2. 12.11 8.14
3. 17 20 27 18 19 27
4. 24 38 48 22 33 47
5. 36 48 60 42 61 86
|
1518b-1t1c-eth-l2bdbasemaclrn-
macip-iacl10sl-10kflows-ndrpdr
|
1. 1.62 19.90
2. 1.62 19.90
3. 22 29 34 22 29 34
4. 27 32 36 22 30 34
5. 28 36 40 26 33 38
|
1518b-2t2c-eth-l2bdbasemaclrn-
macip-iacl10sl-10kflows-ndrpdr
|
1. 1.62 19.90
2. 1.62 19.90
3. 22 24 27 22 23 27
4. 22 27 28 22 26 28
5. 23 29 32 23 30 33
|
1518b-4t4c-eth-l2bdbasemaclrn-
macip-iacl10sl-10kflows-ndrpdr
|
1. 1.62 19.90
2. 1.62 19.90
3. 22 23 27 22 23 29
4. 22 24 28 22 23 25
5. 21 24 27 21 24 27
|
imix-1t1c-eth-l2bdbasemaclrn-
macip-iacl10sl-10kflows-ndrpdr
|
1. 3.44 10.28
2. 3.60 10.75
|
imix-2t2c-eth-l2bdbasemaclrn-
macip-iacl10sl-10kflows-ndrpdr
|
1. 4.75 14.21
2. 6.44 19.27
|
imix-4t4c-eth-l2bdbasemaclrn-
macip-iacl10sl-10kflows-ndrpdr
|
1. 4.81 14.38
2. 6.65 19.90
|
10ge2p1vic1227-eth-l2bdbasemaclrn-macip-iacl1sl-100flows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4 for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required MACIP ACL rules are applied to input paths of both DUT1 interfaces. DUT1 and DUT2 are tested with Cisco-VIC-1227.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-1t1c-eth-l2bdbasemaclrn-
macip-iacl1sl-100flows-ndrpdr
|
1. 5.11 3.43
2. 5.16 3.47
3. 17 31 51 17 32 65
4. 26 55 72 26 62 74
5. 54 79 93 59 79 89
|
64b-2t2c-eth-l2bdbasemaclrn-
macip-iacl1sl-100flows-ndrpdr
|
1. 8.53 5.73
2. 8.86 5.95
3. 17 25 38 17 21 40
4. 26 48 55 27 53 60
5. 28 40 51 31 45 64
|
64b-4t4c-eth-l2bdbasemaclrn-
macip-iacl1sl-100flows-ndrpdr
|
1. 14.97 10.06
2. 16.89 11.35
3. 17 20 24 17 19 23
4. 18 22 27 16 21 26
5. 27 35 46 34 44 55
|
1518b-1t1c-eth-l2bdbasemaclrn-
macip-iacl1sl-100flows-ndrpdr
|
1. 1.62 19.90
2. 1.62 19.90
3. 22 23 25 22 23 24
4. 24 29 32 23 28 31
5. 26 34 38 25 32 36
|
1518b-2t2c-eth-l2bdbasemaclrn-
macip-iacl1sl-100flows-ndrpdr
|
1. 1.62 19.90
2. 1.62 19.90
3. 22 22 23 22 22 23
4. 22 25 28 22 24 28
5. 22 29 32 22 27 31
|
1518b-4t4c-eth-l2bdbasemaclrn-
macip-iacl1sl-100flows-ndrpdr
|
1. 1.60 19.70
2. 1.62 19.90
3. 22 23 26 22 23 26
4. 22 28 30 22 25 29
5. 21 23 25 20 23 25
|
imix-1t1c-eth-l2bdbasemaclrn-
macip-iacl1sl-100flows-ndrpdr
|
1. 4.98 14.88
2. 5.10 15.26
|
imix-2t2c-eth-l2bdbasemaclrn-
macip-iacl1sl-100flows-ndrpdr
|
1. 4.90 14.67
2. 6.65 19.90
|
imix-4t4c-eth-l2bdbasemaclrn-
macip-iacl1sl-100flows-ndrpdr
|
1. 4.74 14.17
2. 6.65 19.90
|
10ge2p1vic1227-eth-l2bdbasemaclrn-macip-iacl1sl-100kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4 for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required MACIP ACL rules are applied to input paths of both DUT1 interfaces. DUT1 and DUT2 are tested with Cisco-VIC-1227.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100k flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-1t1c-eth-l2bdbasemaclrn-
macip-iacl1sl-100kflows-ndrpdr
|
1. 4.72 3.17
2. 4.79 3.22
3. 17 51 73 17 50 71
4. 26 73 87 25 78 90
5. 71 89 107 72 89 101
|
64b-2t2c-eth-l2bdbasemaclrn-
macip-iacl1sl-100kflows-ndrpdr
|
1. 7.94 5.33
2. 8.65 5.81
3. 18 35 53 18 33 50
4. 34 54 61 36 56 61
5. 32 53 64 47 60 72
|
64b-4t4c-eth-l2bdbasemaclrn-
macip-iacl1sl-100kflows-ndrpdr
|
1. 13.12 8.82
2. 15.71 10.56
3. 17 22 29 17 21 29
4. 16 26 34 23 37 44
5. 33 44 53 37 50 63
|
1518b-1t1c-eth-l2bdbasemaclrn-
macip-iacl1sl-100kflows-ndrpdr
|
1. 1.62 19.90
2. 1.62 19.90
3. 22 23 30 22 22 28
4. 24 29 33 22 27 31
5. 27 33 36 25 29 35
|
1518b-2t2c-eth-l2bdbasemaclrn-
macip-iacl1sl-100kflows-ndrpdr
|
1. 1.62 19.90
2. 1.62 19.90
3. 22 22 26 22 22 25
4. 22 25 28 22 23 28
5. 22 28 31 22 28 31
|
1518b-4t4c-eth-l2bdbasemaclrn-
macip-iacl1sl-100kflows-ndrpdr
|
1. 1.61 19.80
2. 1.62 19.90
3. 22 22 23 22 22 23
4. 22 23 26 22 23 26
5. 21 28 30 21 28 31
|
imix-1t1c-eth-l2bdbasemaclrn-
macip-iacl1sl-100kflows-ndrpdr
|
1. 4.64 13.86
2. 4.68 14.00
|
imix-2t2c-eth-l2bdbasemaclrn-
macip-iacl1sl-100kflows-ndrpdr
|
1. 4.98 14.89
2. 6.65 19.90
|
imix-4t4c-eth-l2bdbasemaclrn-
macip-iacl1sl-100kflows-ndrpdr
|
1. 4.62 13.82
2. 6.65 19.90
|
10ge2p1vic1227-eth-l2bdbasemaclrn-macip-iacl1sl-10kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4 for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required MACIP ACL rules are applied to input paths of both DUT1 interfaces. DUT1 and DUT2 are tested with Cisco-VIC-1227.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-1t1c-eth-l2bdbasemaclrn-
macip-iacl1sl-10kflows-ndrpdr
|
1. 4.87 3.27
2. 4.92 3.31
3. 17 24 41 17 24 40
4. 21 68 94 22 84 94
5. 64 89 108 70 93 102
|
64b-2t2c-eth-l2bdbasemaclrn-
macip-iacl1sl-10kflows-ndrpdr
|
1. 8.05 5.41
2. 8.73 5.87
3. 17 30 52 17 28 43
4. 29 55 64 30 58 67
5. 31 48 62 50 62 78
|
64b-4t4c-eth-l2bdbasemaclrn-
macip-iacl1sl-10kflows-ndrpdr
|
1. 13.85 9.31
2. 15.06 10.12
3. 17 19 24 17 18 24
4. 23 34 41 21 35 42
5. 30 40 51 36 53 74
|
1518b-1t1c-eth-l2bdbasemaclrn-
macip-iacl1sl-10kflows-ndrpdr
|
1. 1.62 19.90
2. 1.62 19.90
3. 22 23 25 22 24 25
4. 25 30 32 23 28 31
5. 26 30 34 24 29 34
|
1518b-2t2c-eth-l2bdbasemaclrn-
macip-iacl1sl-10kflows-ndrpdr
|
1. 1.62 19.90
2. 1.62 19.90
3. 22 22 23 22 22 23
4. 22 26 30 22 25 30
5. 23 30 33 23 27 32
|
1518b-4t4c-eth-l2bdbasemaclrn-
macip-iacl1sl-10kflows-ndrpdr
|
1. 1.62 19.90
2. 1.62 19.90
3. 22 22 23 22 23 24
4. 22 27 28 22 25 29
5. 22 29 31 22 28 30
|
imix-1t1c-eth-l2bdbasemaclrn-
macip-iacl1sl-10kflows-ndrpdr
|
1. 4.53 13.53
2. 4.85 14.52
|
imix-2t2c-eth-l2bdbasemaclrn-
macip-iacl1sl-10kflows-ndrpdr
|
1. 4.81 14.38
2. 6.65 19.90
|
imix-4t4c-eth-l2bdbasemaclrn-
macip-iacl1sl-10kflows-ndrpdr
|
1. 4.64 13.89
2. 6.65 19.90
|
10ge2p1vic1227-eth-l2bdbasemaclrn-macip-iacl50sl-100flows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4 for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required MACIP ACL rules are applied to input paths of both DUT1 interfaces. DUT1 and DUT2 are tested with Cisco-VIC-1227.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-1t1c-eth-l2bdbasemaclrn-
macip-iacl50sl-100flows-ndrpdr
|
1. 3.36 2.26
2. 3.46 2.33
3. 17 29 61 17 22 70
4. 24 71 93 28 86 96
5. 59 97 115 59 101 109
|
64b-2t2c-eth-l2bdbasemaclrn-
macip-iacl50sl-100flows-ndrpdr
|
1. 6.31 4.24
2. 6.39 4.30
3. 17 21 30 17 19 30
4. 20 38 51 21 46 56
5. 32 48 54 47 63 75
|
64b-4t4c-eth-l2bdbasemaclrn-
macip-iacl50sl-100flows-ndrpdr
|
1. 10.12 6.80
2. 11.57 7.77
3. 18 24 36 18 19 30
4. 26 45 54 22 48 53
5. 36 50 63 42 59 79
|
1518b-1t1c-eth-l2bdbasemaclrn-
macip-iacl50sl-100flows-ndrpdr
|
1. 1.62 19.90
2. 1.62 19.90
3. 22 22 27 22 22 25
4. 23 32 36 22 29 35
5. 30 37 41 28 35 39
|
1518b-2t2c-eth-l2bdbasemaclrn-
macip-iacl50sl-100flows-ndrpdr
|
1. 1.62 19.90
2. 1.62 19.90
3. 22 22 25 22 22 23
4. 22 26 29 22 23 27
5. 23 30 33 23 27 32
|
1518b-4t4c-eth-l2bdbasemaclrn-
macip-iacl50sl-100flows-ndrpdr
|
1. 1.62 19.90
2. 1.62 19.90
3. 22 22 23 22 22 23
4. 22 24 27 21 23 24
5. 22 28 31 22 27 30
|
imix-1t1c-eth-l2bdbasemaclrn-
macip-iacl50sl-100flows-ndrpdr
|
1. 3.21 9.59
2. 3.37 10.09
|
imix-2t2c-eth-l2bdbasemaclrn-
macip-iacl50sl-100flows-ndrpdr
|
1. 4.94 14.79
2. 6.35 18.99
|
imix-4t4c-eth-l2bdbasemaclrn-
macip-iacl50sl-100flows-ndrpdr
|
1. 4.67 13.95
2. 6.65 19.90
|
10ge2p1vic1227-eth-l2bdbasemaclrn-macip-iacl50sl-100kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4 for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required MACIP ACL rules are applied to input paths of both DUT1 interfaces. DUT1 and DUT2 are tested with Cisco-VIC-1227.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100k flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-1t1c-eth-l2bdbasemaclrn-
macip-iacl50sl-100kflows-ndrpdr
|
1. 3.20 2.15
2. 3.29 2.21
3. 17 37 110 17 33 110
4. 39 103 143 39 113 153
5. 69 128 144 76 123 139
|
64b-2t2c-eth-l2bdbasemaclrn-
macip-iacl50sl-100kflows-ndrpdr
|
1. 5.38 3.61
2. 6.05 4.06
3. 17 34 52 17 34 49
4. 28 61 77 24 62 80
5. 50 75 82 55 79 87
|
64b-4t4c-eth-l2bdbasemaclrn-
macip-iacl50sl-100kflows-ndrpdr
|
1. 9.57 6.43
2. 10.49 7.05
3. 17 26 37 18 38 49
4. 25 42 48 24 43 49
5. 35 47 56 43 59 76
|
1518b-1t1c-eth-l2bdbasemaclrn-
macip-iacl50sl-100kflows-ndrpdr
|
1. 1.62 19.90
2. 1.62 19.90
3. 22 23 28 22 22 26
4. 27 33 38 25 31 36
5. 30 36 40 28 36 40
|
1518b-2t2c-eth-l2bdbasemaclrn-
macip-iacl50sl-100kflows-ndrpdr
|
1. 1.60 19.70
2. 1.62 19.90
3. 22 23 27 22 23 27
4. 22 26 29 22 23 27
5. 23 30 34 23 27 32
|
1518b-4t4c-eth-l2bdbasemaclrn-
macip-iacl50sl-100kflows-ndrpdr
|
1. 1.61 19.80
2. 1.62 19.90
3. 22 22 23 22 22 23
4. 21 23 24 20 22 23
5. 22 29 31 21 25 29
|
imix-1t1c-eth-l2bdbasemaclrn-
macip-iacl50sl-100kflows-ndrpdr
|
1. 3.08 9.22
2. 3.13 9.36
|
imix-2t2c-eth-l2bdbasemaclrn-
macip-iacl50sl-100kflows-ndrpdr
|
1. 5.05 15.11
2. 5.99 17.91
|
imix-4t4c-eth-l2bdbasemaclrn-
macip-iacl50sl-100kflows-ndrpdr
|
1. 4.29 12.82
2. 6.65 19.90
|
10ge2p1vic1227-eth-l2bdbasemaclrn-macip-iacl50sl-10kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4 for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required MACIP ACL rules are applied to input paths of both DUT1 interfaces. DUT1 and DUT2 are tested with Cisco-VIC-1227.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-1t1c-eth-l2bdbasemaclrn-
macip-iacl50sl-10kflows-ndrpdr
|
1. 3.28 2.21
2. 3.32 2.23
3. 17 27 64 17 21 43
4. 30 99 142 20 107 142
5. 75 123 154 78 126 145
|
64b-2t2c-eth-l2bdbasemaclrn-
macip-iacl50sl-10kflows-ndrpdr
|
1. 5.86 3.94
2. 6.10 4.10
3. 17 36 58 17 57 72
4. 31 56 68 19 55 70
5. 35 47 58 47 64 81
|
64b-4t4c-eth-l2bdbasemaclrn-
macip-iacl50sl-10kflows-ndrpdr
|
1. 11.24 7.55
2. 11.46 7.70
3. 17 24 33 18 22 32
4. 21 34 40 20 34 43
5. 28 38 46 39 57 75
|
1518b-1t1c-eth-l2bdbasemaclrn-
macip-iacl50sl-10kflows-ndrpdr
|
1. 1.62 19.90
2. 1.62 19.90
3. 22 25 31 22 25 29
4. 22 33 37 22 33 37
5. 30 37 42 29 36 40
|
1518b-2t2c-eth-l2bdbasemaclrn-
macip-iacl50sl-10kflows-ndrpdr
|
1. 1.62 19.90
2. 1.62 19.90
3. 22 22 23 22 22 23
4. 22 26 28 22 24 28
5. 23 30 33 23 29 33
|
1518b-4t4c-eth-l2bdbasemaclrn-
macip-iacl50sl-10kflows-ndrpdr
|
1. 1.59 19.60
2. 1.62 19.90
3. 22 23 23 22 23 23
4. 22 23 26 22 23 26
5. 21 29 31 21 25 28
|
imix-1t1c-eth-l2bdbasemaclrn-
macip-iacl50sl-10kflows-ndrpdr
|
1. 2.83 8.46
2. 3.21 9.59
|
imix-2t2c-eth-l2bdbasemaclrn-
macip-iacl50sl-10kflows-ndrpdr
|
1. 5.00 14.95
2. 5.94 17.76
|
imix-4t4c-eth-l2bdbasemaclrn-
macip-iacl50sl-10kflows-ndrpdr
|
1. 4.86 14.52
2. 6.65 19.90
|
10ge2p1vic1227-eth-l2bdbasemaclrn-ndrpdr
RFC2544: Pkt throughput L2BD test cases
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4 for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 bridge- domain and MAC learning enabled. DUT1 and DUT2 tested with Cisco-VIC-1227.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 254 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-1t1c-
eth-l2bdbasemaclrn-ndrpdr
|
1. 8.84 5.94
2. 10.22 6.87
3. 17 33 41 17 33 42
4. 26 41 46 27 41 46
5. 82 100 120 84 101 120
|
64b-2t2c-
eth-l2bdbasemaclrn-ndrpdr
|
1. 13.56 9.11
2. 18.40 12.36
3. 17 24 39 18 27 40
4. 28 38 43 29 38 44
5. 40 47 53 38 45 52
|
64b-4t4c-
eth-l2bdbasemaclrn-ndrpdr
|
1. 13.87 9.32
2. 19.58 13.16
3. 17 18 22 17 18 20
4. 16 20 24 16 19 23
5. 21 25 30 20 24 29
|
1518b-1t1c-
eth-l2bdbasemaclrn-ndrpdr
|
1. 1.61 19.80
2. 1.62 19.90
3. 22 22 24 22 22 23
4. 22 27 30 22 25 30
5. 25 31 35 24 31 36
|
1518b-2t2c-
eth-l2bdbasemaclrn-ndrpdr
|
1. 1.61 19.80
2. 1.62 19.90
3. 22 22 22 22 22 23
4. 22 27 29 22 25 28
5. 22 29 32 21 25 30
|
1518b-4t4c-
eth-l2bdbasemaclrn-ndrpdr
|
1. 1.62 19.90
2. 1.62 19.90
3. 22 22 26 22 23 27
4. 22 23 27 22 23 27
5. 20 28 30 20 27 30
|
imix-1t1c-
eth-l2bdbasemaclrn-ndrpdr
|
1. 4.98 14.89
2. 6.65 19.90
|
imix-2t2c-
eth-l2bdbasemaclrn-ndrpdr
|
1. 4.55 13.61
2. 6.65 19.90
|
imix-4t4c-
eth-l2bdbasemaclrn-ndrpdr
|
1. 4.60 13.75
2. 6.65 19.90
|
10ge2p1vic1227-eth-l2bdbasemaclrn-oacl10sf-100flows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Cisco-VIC-1227.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100 flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-1t1c-eth-
l2bdbasemaclrn-oacl10sf-100flows-ndrpdr
|
1. 5.05 3.39
2. 5.21 3.50
3. 17 35 64 17 52 87
4. 27 71 87 23 87 102
5. 66 94 116 78 102 123
|
64b-2t2c-eth-
l2bdbasemaclrn-oacl10sf-100flows-ndrpdr
|
1. 9.47 6.36
2. 10.21 6.86
3. 18 29 38 17 22 31
4. 24 39 47 23 39 49
5. 47 56 63 46 56 63
|
64b-4t4c-eth-
l2bdbasemaclrn-oacl10sf-100flows-ndrpdr
|
1. 13.43 9.02
2. 17.07 11.47
3. 18 23 30 18 21 30
4. 23 33 39 21 33 39
5. 35 46 56 39 77 175
|
1518b-1t1c-eth-
l2bdbasemaclrn-oacl10sf-100flows-ndrpdr
|
1. 1.51 18.55
2. 1.62 19.90
3. 22 26 32 22 26 32
4. 22 31 35 22 31 34
5. 27 30 33 25 30 34
|
1518b-2t2c-eth-
l2bdbasemaclrn-oacl10sf-100flows-ndrpdr
|
1. 1.59 19.51
2. 1.62 19.90
3. 22 23 24 22 23 24
4. 22 28 31 22 28 31
5. 23 30 32 23 29 32
|
1518b-4t4c-eth-
l2bdbasemaclrn-oacl10sf-100flows-ndrpdr
|
1. 1.59 19.51
2. 1.62 19.90
3. 22 22 23 22 23 23
4. 22 25 27 21 23 27
5. 22 29 31 22 29 31
|
imix-1t1c-eth-
l2bdbasemaclrn-oacl10sf-100flows-ndrpdr
|
1. 5.13 15.34
2. 5.23 15.65
|
imix-2t2c-eth-
l2bdbasemaclrn-oacl10sf-100flows-ndrpdr
|
1. 4.78 14.31
2. 6.65 19.90
|
imix-4t4c-eth-
l2bdbasemaclrn-oacl10sf-100flows-ndrpdr
|
1. 4.67 13.95
2. 6.65 19.90
|
10ge2p1vic1227-eth-l2bdbasemaclrn-oacl10sf-100kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Cisco-VIC-1227.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-1t1c-eth-
l2bdbasemaclrn-oacl10sf-100kflows-ndrpdr
|
1. 5.14 3.45
2. 5.21 3.50
3. 17 51 88 17 58 86
4. 27 83 101 25 85 98
5. 74 110 131 88 105 121
|
64b-2t2c-eth-
l2bdbasemaclrn-oacl10sf-100kflows-ndrpdr
|
1. 9.25 6.21
2. 10.27 6.90
3. 18 50 59 18 49 56
4. 31 49 56 30 47 53
5. 57 68 77 55 66 74
|
64b-4t4c-eth-
l2bdbasemaclrn-oacl10sf-100kflows-ndrpdr
|
1. 13.38 8.99
2. 17.36 11.66
3. 16 21 29 18 20 26
4. 30 39 46 28 39 46
5. 39 51 60 47 102 179
|
1518b-1t1c-eth-
l2bdbasemaclrn-oacl10sf-100kflows-ndrpdr
|
1. 1.55 19.12
2. 1.62 19.90
3. 22 23 26 22 22 24
4. 26 31 35 23 29 34
5. 28 34 37 26 33 37
|
1518b-2t2c-eth-
l2bdbasemaclrn-oacl10sf-100kflows-ndrpdr
|
1. 1.55 19.02
2. 1.62 19.90
3. 22 22 24 22 22 23
4. 22 26 28 22 23 27
5. 23 30 33 23 27 32
|
1518b-4t4c-eth-
l2bdbasemaclrn-oacl10sf-100kflows-ndrpdr
|
1. 1.58 19.41
2. 1.62 19.90
3. 22 23 24 22 23 23
4. 22 28 30 21 25 29
5. 22 25 28 22 26 30
|
imix-1t1c-eth-
l2bdbasemaclrn-oacl10sf-100kflows-ndrpdr
|
1. 5.06 15.13
2. 5.21 15.59
|
imix-2t2c-eth-
l2bdbasemaclrn-oacl10sf-100kflows-ndrpdr
|
1. 4.62 13.81
2. 6.65 19.90
|
imix-4t4c-eth-
l2bdbasemaclrn-oacl10sf-100kflows-ndrpdr
|
1. 4.55 13.61
2. 6.65 19.90
|
10ge2p1vic1227-eth-l2bdbasemaclrn-oacl10sf-10kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Cisco-VIC-1227.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-1t1c-eth-
l2bdbasemaclrn-oacl10sf-10kflows-ndrpdr
|
1. 5.17 3.47
2. 5.22 3.51
3. 17 42 86 17 50 89
4. 27 78 93 25 87 100
5. 65 93 112 70 95 111
|
64b-2t2c-eth-
l2bdbasemaclrn-oacl10sf-10kflows-ndrpdr
|
1. 9.36 6.29
2. 10.35 6.95
3. 17 42 54 17 34 50
4. 25 39 48 23 37 48
5. 45 55 63 45 55 63
|
64b-4t4c-eth-
l2bdbasemaclrn-oacl10sf-10kflows-ndrpdr
|
1. 13.91 9.35
2. 17.78 11.95
3. 17 28 37 18 21 36
4. 26 36 40 25 35 39
5. 42 63 92 49 101 164
|
1518b-1t1c-eth-
l2bdbasemaclrn-oacl10sf-10kflows-ndrpdr
|
1. 1.58 19.41
2. 1.62 19.90
3. 22 23 26 22 22 24
4. 26 31 34 24 30 34
5. 27 33 38 26 33 37
|
1518b-2t2c-eth-
l2bdbasemaclrn-oacl10sf-10kflows-ndrpdr
|
1. 1.58 19.41
2. 1.62 19.90
3. 22 23 25 22 23 25
4. 22 29 32 22 30 32
5. 22 26 30 22 25 29
|
1518b-4t4c-eth-
l2bdbasemaclrn-oacl10sf-10kflows-ndrpdr
|
1. 1.62 19.90
2. 1.62 19.90
3. 22 23 23 22 23 24
4. 22 24 27 21 24 27
5. 22 28 31 22 27 31
|
imix-1t1c-eth-
l2bdbasemaclrn-oacl10sf-10kflows-ndrpdr
|
1. 4.98 14.88
2. 5.23 15.64
|
imix-2t2c-eth-
l2bdbasemaclrn-oacl10sf-10kflows-ndrpdr
|
1. 4.83 14.45
2. 6.65 19.90
|
imix-4t4c-eth-
l2bdbasemaclrn-oacl10sf-10kflows-ndrpdr
|
1. 4.81 14.38
2. 6.65 19.90
|
10ge2p1vic1227-eth-l2bdbasemaclrn-oacl10sl-100flows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Cisco-VIC-1227.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100 flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-1t1c-eth-
l2bdbasemaclrn-oacl10sl-100flows-ndrpdr
|
1. 5.12 3.44
2. 5.22 3.51
3. 17 57 100 17 82 102
4. 25 68 88 24 79 97
5. 71 106 125 86 103 117
|
64b-2t2c-eth-
l2bdbasemaclrn-oacl10sl-100flows-ndrpdr
|
1. 9.36 6.29
2. 10.34 6.95
3. 18 39 52 18 39 49
4. 26 43 52 23 44 51
5. 48 57 66 47 59 68
|
64b-4t4c-eth-
l2bdbasemaclrn-oacl10sl-100flows-ndrpdr
|
1. 14.65 9.84
2. 17.48 11.75
3. 17 22 31 18 18 24
4. 27 36 41 25 35 40
5. 41 56 81 44 67 138
|
1518b-1t1c-eth-
l2bdbasemaclrn-oacl10sl-100flows-ndrpdr
|
1. 1.62 19.90
2. 1.62 19.90
3. 22 22 26 22 22 24
4. 26 31 33 23 27 32
5. 27 34 38 26 33 37
|
1518b-2t2c-eth-
l2bdbasemaclrn-oacl10sl-100flows-ndrpdr
|
1. 1.58 19.41
2. 1.62 19.90
3. 22 23 25 22 23 24
4. 22 28 31 22 28 32
5. 22 26 31 22 26 32
|
1518b-4t4c-eth-
l2bdbasemaclrn-oacl10sl-100flows-ndrpdr
|
1. 1.52 18.74
2. 1.62 19.90
3. 22 23 23 22 23 23
4. 22 26 29 22 26 29
5. 22 29 32 22 25 28
|
imix-1t1c-eth-
l2bdbasemaclrn-oacl10sl-100flows-ndrpdr
|
1. 5.15 15.40
2. 5.23 15.63
|
imix-2t2c-eth-
l2bdbasemaclrn-oacl10sl-100flows-ndrpdr
|
1. 4.69 14.02
2. 6.65 19.90
|
imix-4t4c-eth-
l2bdbasemaclrn-oacl10sl-100flows-ndrpdr
|
1. 4.69 14.02
2. 6.65 19.90
|
10ge2p1vic1227-eth-l2bdbasemaclrn-oacl10sl-100kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Cisco-VIC-1227.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-1t1c-eth-
l2bdbasemaclrn-oacl10sl-100kflows-ndrpdr
|
1. 5.18 3.48
2. 5.23 3.52
3. 17 48 82 17 57 83
4. 25 62 75 20 67 81
5. 75 106 128 84 101 115
|
64b-2t2c-eth-
l2bdbasemaclrn-oacl10sl-100kflows-ndrpdr
|
1. 8.79 5.90
2. 10.36 6.96
3. 18 40 50 18 38 48
4. 34 52 60 29 50 57
5. 49 59 66 48 57 63
|
64b-4t4c-eth-
l2bdbasemaclrn-oacl10sl-100kflows-ndrpdr
|
1. 13.10 8.80
2. 16.32 10.97
3. 18 27 35 18 25 33
4. 26 31 35 24 29 33
5. 34 46 59 31 40 49
|
1518b-1t1c-eth-
l2bdbasemaclrn-oacl10sl-100kflows-ndrpdr
|
1. 1.62 19.90
2. 1.62 19.90
3. 22 23 25 22 23 25
4. 26 31 33 25 30 33
5. 26 29 33 25 28 32
|
1518b-2t2c-eth-
l2bdbasemaclrn-oacl10sl-100kflows-ndrpdr
|
1. 1.38 16.96
2. 1.62 19.90
3. 22 22 24 22 23 24
4. 22 28 30 22 28 31
5. 23 31 34 22 26 32
|
1518b-4t4c-eth-
l2bdbasemaclrn-oacl10sl-100kflows-ndrpdr
|
1. 1.59 19.51
2. 1.62 19.90
3. 22 23 27 22 23 27
4. 22 24 27 21 23 26
5. 22 29 32 22 25 29
|
imix-1t1c-eth-
l2bdbasemaclrn-oacl10sl-100kflows-ndrpdr
|
1. 5.08 15.18
2. 5.20 15.56
|
imix-2t2c-eth-
l2bdbasemaclrn-oacl10sl-100kflows-ndrpdr
|
1. 4.95 14.82
2. 6.65 19.90
|
imix-4t4c-eth-
l2bdbasemaclrn-oacl10sl-100kflows-ndrpdr
|
1. 4.71 14.09
2. 6.65 19.90
|
10ge2p1vic1227-eth-l2bdbasemaclrn-oacl10sl-10kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Cisco-VIC-1227.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-1t1c-eth-
l2bdbasemaclrn-oacl10sl-10kflows-ndrpdr
|
1. 5.14 3.45
2. 5.22 3.51
3. 17 40 73 17 50 73
4. 28 69 82 21 74 89
5. 67 93 110 72 95 107
|
64b-2t2c-eth-
l2bdbasemaclrn-oacl10sl-10kflows-ndrpdr
|
1. 9.11 6.12
2. 10.02 6.73
3. 17 22 50 17 18 34
4. 27 44 55 27 47 55
5. 49 64 72 49 62 68
|
64b-4t4c-eth-
l2bdbasemaclrn-oacl10sl-10kflows-ndrpdr
|
1. 13.29 8.93
2. 16.56 11.13
3. 18 22 28 18 21 27
4. 29 36 40 28 35 38
5. 38 55 78 34 44 52
|
1518b-1t1c-eth-
l2bdbasemaclrn-oacl10sl-10kflows-ndrpdr
|
1. 1.56 19.21
2. 1.62 19.90
3. 22 23 29 22 22 25
4. 24 32 36 23 32 35
5. 28 34 38 26 32 37
|
1518b-2t2c-eth-
l2bdbasemaclrn-oacl10sl-10kflows-ndrpdr
|
1. 1.61 19.80
2. 1.62 19.90
3. 22 23 23 22 23 23
4. 22 25 28 22 24 26
5. 23 30 32 23 30 32
|
1518b-4t4c-eth-
l2bdbasemaclrn-oacl10sl-10kflows-ndrpdr
|
1. 1.50 18.46
2. 1.62 19.90
3. 22 23 23 22 23 24
4. 22 24 27 22 23 26
5. 22 30 32 22 25 28
|
imix-1t1c-eth-
l2bdbasemaclrn-oacl10sl-10kflows-ndrpdr
|
1. 4.94 14.78
2. 5.22 15.62
|
imix-2t2c-eth-
l2bdbasemaclrn-oacl10sl-10kflows-ndrpdr
|
1. 4.67 13.95
2. 6.65 19.90
|
imix-4t4c-eth-
l2bdbasemaclrn-oacl10sl-10kflows-ndrpdr
|
1. 4.76 14.24
2. 6.65 19.90
|
10ge2p1vic1227-eth-l2bdbasemaclrn-oacl1sf-100flows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Cisco-VIC-1227.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100 flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-1t1c-eth-
l2bdbasemaclrn-oacl1sf-100flows-ndrpdr
|
1. 5.14 3.46
2. 5.22 3.51
3. 17 45 65 17 50 66
4. 37 68 83 23 73 84
5. 67 94 121 76 95 108
|
64b-2t2c-eth-
l2bdbasemaclrn-oacl1sf-100flows-ndrpdr
|
1. 9.35 6.29
2. 10.29 6.91
3. 18 33 42 18 34 43
4. 25 38 45 23 40 49
5. 47 60 66 52 63 70
|
64b-4t4c-eth-
l2bdbasemaclrn-oacl1sf-100flows-ndrpdr
|
1. 13.96 9.38
2. 17.32 11.64
3. 17 22 27 17 19 22
4. 20 26 33 19 25 29
5. 35 45 53 38 48 64
|
1518b-1t1c-eth-
l2bdbasemaclrn-oacl1sf-100flows-ndrpdr
|
1. 1.62 19.90
2. 1.62 19.90
3. 22 25 32 22 26 32
4. 22 29 35 23 29 32
5. 27 31 37 25 30 35
|
1518b-2t2c-eth-
l2bdbasemaclrn-oacl1sf-100flows-ndrpdr
|
1. 1.59 19.51
2. 1.62 19.90
3. 22 23 28 22 23 29
4. 22 26 31 22 26 31
5. 22 26 29 22 26 28
|
1518b-4t4c-eth-
l2bdbasemaclrn-oacl1sf-100flows-ndrpdr
|
1. 1.52 18.65
2. 1.62 19.90
3. 22 23 28 22 23 28
4. 23 27 29 23 27 29
5. 22 28 31 21 29 31
|
imix-1t1c-eth-
l2bdbasemaclrn-oacl1sf-100flows-ndrpdr
|
1. 4.76 14.23
2. 5.23 15.64
|
imix-2t2c-eth-
l2bdbasemaclrn-oacl1sf-100flows-ndrpdr
|
1. 4.64 13.89
2. 6.65 19.90
|
imix-4t4c-eth-
l2bdbasemaclrn-oacl1sf-100flows-ndrpdr
|
1. 4.57 13.68
2. 6.65 19.90
|
10ge2p1vic1227-eth-l2bdbasemaclrn-oacl1sf-100kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Cisco-VIC-1227.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-1t1c-eth-
l2bdbasemaclrn-oacl1sf-100kflows-ndrpdr
|
1. 5.17 3.48
2. 5.22 3.51
3. 17 38 64 17 43 62
4. 37 60 75 36 62 76
5. 60 82 116 64 83 99
|
64b-2t2c-eth-
l2bdbasemaclrn-oacl1sf-100kflows-ndrpdr
|
1. 9.38 6.30
2. 10.21 6.86
3. 18 29 35 17 21 30
4. 22 30 38 21 33 40
5. 44 54 61 48 57 63
|
64b-4t4c-eth-
l2bdbasemaclrn-oacl1sf-100kflows-ndrpdr
|
1. 13.33 8.96
2. 17.82 11.97
3. 17 21 26 18 19 22
4. 21 30 36 20 28 34
5. 38 49 65 39 54 81
|
1518b-1t1c-eth-
l2bdbasemaclrn-oacl1sf-100kflows-ndrpdr
|
1. 1.60 19.70
2. 1.62 19.90
3. 22 24 31 22 24 31
4. 22 33 37 22 33 37
5. 28 33 38 26 31 37
|
1518b-2t2c-eth-
l2bdbasemaclrn-oacl1sf-100kflows-ndrpdr
|
1. 1.62 19.90
2. 1.62 19.90
3. 22 23 28 22 23 27
4. 22 26 28 22 25 28
5. 23 30 33 23 30 32
|
1518b-4t4c-eth-
l2bdbasemaclrn-oacl1sf-100kflows-ndrpdr
|
1. 1.58 19.41
2. 1.62 19.90
3. 22 22 23 22 22 23
4. 22 24 26 22 24 27
5. 22 26 29 21 25 29
|
imix-1t1c-eth-
l2bdbasemaclrn-oacl1sf-100kflows-ndrpdr
|
1. 5.08 15.19
2. 5.23 15.66
|
imix-2t2c-eth-
l2bdbasemaclrn-oacl1sf-100kflows-ndrpdr
|
1. 4.55 13.61
2. 6.65 19.90
|
imix-4t4c-eth-
l2bdbasemaclrn-oacl1sf-100kflows-ndrpdr
|
1. 4.78 14.31
2. 6.65 19.90
|
10ge2p1vic1227-eth-l2bdbasemaclrn-oacl1sf-10kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Cisco-VIC-1227.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-1t1c-eth-
l2bdbasemaclrn-oacl1sf-10kflows-ndrpdr
|
1. 5.11 3.44
2. 5.22 3.50
3. 17 42 71 17 48 76
4. 24 68 82 23 71 87
5. 69 95 113 74 95 112
|
64b-2t2c-eth-
l2bdbasemaclrn-oacl1sf-10kflows-ndrpdr
|
1. 9.82 6.60
2. 10.32 6.93
3. 18 47 59 18 46 54
4. 23 34 42 23 34 43
5. 51 62 69 53 64 77
|
64b-4t4c-eth-
l2bdbasemaclrn-oacl1sf-10kflows-ndrpdr
|
1. 15.12 10.16
2. 18.19 12.23
3. 17 21 30 18 19 26
4. 26 38 43 23 34 39
5. 46 79 150 39 51 65
|
1518b-1t1c-eth-
l2bdbasemaclrn-oacl1sf-10kflows-ndrpdr
|
1. 1.55 19.02
2. 1.62 19.90
3. 22 23 28 22 23 27
4. 25 33 37 24 28 33
5. 27 35 39 25 33 37
|
1518b-2t2c-eth-
l2bdbasemaclrn-oacl1sf-10kflows-ndrpdr
|
1. 1.61 19.80
2. 1.62 19.90
3. 22 23 27 22 23 25
4. 22 27 28 22 26 28
5. 23 30 33 23 26 32
|
1518b-4t4c-eth-
l2bdbasemaclrn-oacl1sf-10kflows-ndrpdr
|
1. 1.48 18.19
2. 1.62 19.90
3. 22 22 23 22 23 23
4. 22 24 27 22 23 26
5. 22 29 31 22 29 31
|
imix-1t1c-eth-
l2bdbasemaclrn-oacl1sf-10kflows-ndrpdr
|
1. 4.94 14.76
2. 5.22 15.60
|
imix-2t2c-eth-
l2bdbasemaclrn-oacl1sf-10kflows-ndrpdr
|
1. 4.55 13.61
2. 6.65 19.90
|
imix-4t4c-eth-
l2bdbasemaclrn-oacl1sf-10kflows-ndrpdr
|
1. 4.55 13.61
2. 6.65 19.90
|
10ge2p1vic1227-eth-l2bdbasemaclrn-oacl1sl-100flows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Cisco-VIC-1227.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100 flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-1t1c-eth-
l2bdbasemaclrn-oacl1sl-100flows-ndrpdr
|
1. 5.19 3.49
2. 5.24 3.52
3. 17 46 79 17 63 80
4. 29 52 69 35 59 70
5. 67 93 114 76 99 109
|
64b-2t2c-eth-
l2bdbasemaclrn-oacl1sl-100flows-ndrpdr
|
1. 9.57 6.43
2. 10.26 6.90
3. 18 32 43 18 34 45
4. 29 45 53 28 44 53
5. 51 60 66 53 62 69
|
64b-4t4c-eth-
l2bdbasemaclrn-oacl1sl-100flows-ndrpdr
|
1. 13.61 9.15
2. 18.19 12.23
3. 18 26 38 18 24 36
4. 22 33 38 19 33 36
5. 49 82 141 39 54 72
|
1518b-1t1c-eth-
l2bdbasemaclrn-oacl1sl-100flows-ndrpdr
|
1. 1.62 19.90
2. 1.62 19.90
3. 22 25 29 22 23 29
4. 25 31 34 22 29 34
5. 27 35 39 26 31 36
|
1518b-2t2c-eth-
l2bdbasemaclrn-oacl1sl-100flows-ndrpdr
|
1. 1.59 19.51
2. 1.62 19.90
3. 22 22 24 22 22 24
4. 22 26 28 22 25 28
5. 23 30 33 23 26 33
|
1518b-4t4c-eth-
l2bdbasemaclrn-oacl1sl-100flows-ndrpdr
|
1. 1.61 19.80
2. 1.62 19.90
3. 22 23 28 22 23 30
4. 22 26 28 22 26 29
5. 22 25 29 21 25 30
|
imix-1t1c-eth-
l2bdbasemaclrn-oacl1sl-100flows-ndrpdr
|
1. 4.98 14.88
2. 5.21 15.57
|
imix-2t2c-eth-
l2bdbasemaclrn-oacl1sl-100flows-ndrpdr
|
1. 4.62 13.82
2. 6.65 19.90
|
imix-4t4c-eth-
l2bdbasemaclrn-oacl1sl-100flows-ndrpdr
|
1. 4.62 13.82
2. 6.65 19.90
|
10ge2p1vic1227-eth-l2bdbasemaclrn-oacl1sl-100kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Cisco-VIC-1227.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-1t1c-eth-
l2bdbasemaclrn-oacl1sl-100kflows-ndrpdr
|
1. 5.18 3.48
2. 5.23 3.51
3. 17 28 44 17 29 46
4. 24 41 53 26 48 59
5. 60 80 94 61 81 99
|
64b-2t2c-eth-
l2bdbasemaclrn-oacl1sl-100kflows-ndrpdr
|
1. 9.33 6.27
2. 10.31 6.93
3. 18 30 37 18 27 38
4. 23 34 42 22 32 40
5. 40 48 55 46 54 64
|
64b-4t4c-eth-
l2bdbasemaclrn-oacl1sl-100kflows-ndrpdr
|
1. 12.99 8.73
2. 17.97 12.08
3. 17 23 32 18 20 28
4. 27 37 43 25 36 41
5. 39 52 62 46 73 142
|
1518b-1t1c-eth-
l2bdbasemaclrn-oacl1sl-100kflows-ndrpdr
|
1. 1.62 19.90
2. 1.62 19.90
3. 22 23 29 22 22 26
4. 23 30 34 22 27 33
5. 27 34 38 26 34 38
|
1518b-2t2c-eth-
l2bdbasemaclrn-oacl1sl-100kflows-ndrpdr
|
1. 1.55 19.02
2. 1.62 19.90
3. 22 22 24 22 22 24
4. 22 28 31 22 25 31
5. 23 30 32 22 27 32
|
1518b-4t4c-eth-
l2bdbasemaclrn-oacl1sl-100kflows-ndrpdr
|
1. 1.55 19.02
2. 1.62 19.90
3. 22 23 24 22 23 24
4. 22 28 30 22 28 30
5. 22 29 32 21 25 27
|
imix-1t1c-eth-
l2bdbasemaclrn-oacl1sl-100kflows-ndrpdr
|
1. 4.93 14.73
2. 5.10 15.26
|
imix-2t2c-eth-
l2bdbasemaclrn-oacl1sl-100kflows-ndrpdr
|
1. 5.05 15.12
2. 6.65 19.90
|
imix-4t4c-eth-
l2bdbasemaclrn-oacl1sl-100kflows-ndrpdr
|
1. 4.64 13.88
2. 6.65 19.90
|
10ge2p1vic1227-eth-l2bdbasemaclrn-oacl1sl-10kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Cisco-VIC-1227.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-1t1c-eth-
l2bdbasemaclrn-oacl1sl-10kflows-ndrpdr
|
1. 5.14 3.45
2. 5.24 3.52
3. 17 53 74 17 56 72
4. 28 55 80 20 62 73
5. 67 95 113 72 93 101
|
64b-2t2c-eth-
l2bdbasemaclrn-oacl1sl-10kflows-ndrpdr
|
1. 9.58 6.44
2. 10.28 6.91
3. 18 22 27 18 21 27
4. 23 31 37 23 32 38
5. 39 48 54 45 53 61
|
64b-4t4c-eth-
l2bdbasemaclrn-oacl1sl-10kflows-ndrpdr
|
1. 13.80 9.27
2. 17.80 11.96
3. 17 21 26 17 19 24
4. 20 26 33 19 25 32
5. 39 52 71 45 78 138
|
1518b-1t1c-eth-
l2bdbasemaclrn-oacl1sl-10kflows-ndrpdr
|
1. 1.61 19.80
2. 1.62 19.90
3. 22 24 30 22 23 29
4. 26 32 34 25 31 34
5. 27 35 39 26 34 38
|
1518b-2t2c-eth-
l2bdbasemaclrn-oacl1sl-10kflows-ndrpdr
|
1. 1.61 19.80
2. 1.62 19.90
3. 22 23 23 22 23 23
4. 22 29 31 22 28 31
5. 22 30 33 23 27 33
|
1518b-4t4c-eth-
l2bdbasemaclrn-oacl1sl-10kflows-ndrpdr
|
1. 1.57 19.31
2. 1.62 19.90
3. 22 23 24 22 23 25
4. 22 26 29 22 25 29
5. 22 29 31 21 25 30
|
imix-1t1c-eth-
l2bdbasemaclrn-oacl1sl-10kflows-ndrpdr
|
1. 5.01 14.98
2. 5.21 15.59
|
imix-2t2c-eth-
l2bdbasemaclrn-oacl1sl-10kflows-ndrpdr
|
1. 4.86 14.52
2. 6.65 19.90
|
imix-4t4c-eth-
l2bdbasemaclrn-oacl1sl-10kflows-ndrpdr
|
1. 4.69 14.02
2. 6.65 19.90
|
10ge2p1vic1227-eth-l2bdbasemaclrn-oacl50sf-100flows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Cisco-VIC-1227.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100 flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-1t1c-eth-
l2bdbasemaclrn-oacl50sf-100flows-ndrpdr
|
1. 5.07 3.41
2. 5.12 3.44
3. 17 28 44 17 28 60
4. 24 50 64 25 52 62
5. 61 81 97 60 80 94
|
64b-2t2c-eth-
l2bdbasemaclrn-oacl50sf-100flows-ndrpdr
|
1. 9.41 6.32
2. 10.19 6.85
3. 17 50 60 17 25 49
4. 30 49 56 30 44 51
5. 46 56 63 46 56 63
|
64b-4t4c-eth-
l2bdbasemaclrn-oacl50sf-100flows-ndrpdr
|
1. 14.83 9.96
2. 17.75 11.93
3. 18 22 28 18 19 25
4. 21 31 36 21 31 36
5. 42 59 81 46 99 174
|
1518b-1t1c-eth-
l2bdbasemaclrn-oacl50sf-100flows-ndrpdr
|
1. 1.61 19.80
2. 1.62 19.90
3. 22 25 31 22 23 29
4. 26 31 34 24 30 33
5. 27 35 39 26 33 38
|
1518b-2t2c-eth-
l2bdbasemaclrn-oacl50sf-100flows-ndrpdr
|
1. 1.59 19.51
2. 1.62 19.90
3. 22 23 27 22 22 25
4. 22 29 31 22 25 31
5. 22 27 31 22 26 31
|
1518b-4t4c-eth-
l2bdbasemaclrn-oacl50sf-100flows-ndrpdr
|
1. 1.62 19.90
2. 1.62 19.90
3. 22 23 27 22 23 28
4. 22 28 30 22 24 29
5. 22 29 31 22 29 32
|
imix-1t1c-eth-
l2bdbasemaclrn-oacl50sf-100flows-ndrpdr
|
1. 4.96 14.83
2. 5.13 15.36
|
imix-2t2c-eth-
l2bdbasemaclrn-oacl50sf-100flows-ndrpdr
|
1. 4.62 13.82
2. 6.65 19.90
|
imix-4t4c-eth-
l2bdbasemaclrn-oacl50sf-100flows-ndrpdr
|
1. 4.71 14.09
2. 6.65 19.90
|
10ge2p1vic1227-eth-l2bdbasemaclrn-oacl50sf-100kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Cisco-VIC-1227.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-1t1c-eth-
l2bdbasemaclrn-oacl50sf-100kflows-ndrpdr
|
1. 5.09 3.42
2. 5.11 3.44
3. 17 25 52 17 24 77
4. 28 52 70 29 60 70
5. 60 85 100 62 87 100
|
64b-2t2c-eth-
l2bdbasemaclrn-oacl50sf-100kflows-ndrpdr
|
1. 9.44 6.34
2. 10.33 6.94
3. 18 37 48 18 28 43
4. 28 41 50 26 39 48
5. 46 55 63 44 55 64
|
64b-4t4c-eth-
l2bdbasemaclrn-oacl50sf-100kflows-ndrpdr
|
1. 13.92 9.36
2. 17.53 11.78
3. 16 23 27 17 18 20
4. 21 30 36 18 25 31
5. 49 83 150 41 50 62
|
1518b-1t1c-eth-
l2bdbasemaclrn-oacl50sf-100kflows-ndrpdr
|
1. 1.57 19.31
2. 1.62 19.90
3. 22 25 30 22 23 28
4. 22 31 34 22 27 33
5. 27 35 39 26 33 37
|
1518b-2t2c-eth-
l2bdbasemaclrn-oacl50sf-100kflows-ndrpdr
|
1. 1.58 19.41
2. 1.62 19.90
3. 22 22 23 22 23 23
4. 22 29 31 22 28 31
5. 23 30 33 23 27 32
|
1518b-4t4c-eth-
l2bdbasemaclrn-oacl50sf-100kflows-ndrpdr
|
1. 1.41 17.39
2. 1.62 19.90
3. 22 23 25 22 23 23
4. 22 25 28 22 25 29
5. 22 29 32 21 25 28
|
imix-1t1c-eth-
l2bdbasemaclrn-oacl50sf-100kflows-ndrpdr
|
1. 4.72 14.11
2. 5.14 15.36
|
imix-2t2c-eth-
l2bdbasemaclrn-oacl50sf-100kflows-ndrpdr
|
1. 4.76 14.24
2. 6.65 19.90
|
imix-4t4c-eth-
l2bdbasemaclrn-oacl50sf-100kflows-ndrpdr
|
1. 4.64 13.88
2. 6.65 19.90
|
10ge2p1vic1227-eth-l2bdbasemaclrn-oacl50sf-10kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Cisco-VIC-1227.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-1t1c-eth-
l2bdbasemaclrn-oacl50sf-10kflows-ndrpdr
|
1. 5.07 3.41
2. 5.12 3.44
3. 17 29 63 17 31 84
4. 33 76 95 28 79 100
5. 64 96 116 71 100 113
|
64b-2t2c-eth-
l2bdbasemaclrn-oacl50sf-10kflows-ndrpdr
|
1. 8.25 5.55
2. 10.34 6.95
3. 18 38 46 18 34 44
4. 28 45 54 28 44 53
5. 49 59 68 48 59 67
|
64b-4t4c-eth-
l2bdbasemaclrn-oacl50sf-10kflows-ndrpdr
|
1. 13.39 9.00
2. 17.20 11.56
3. 18 23 34 18 19 26
4. 28 39 44 26 38 43
5. 39 50 61 43 109 196
|
1518b-1t1c-eth-
l2bdbasemaclrn-oacl50sf-10kflows-ndrpdr
|
1. 1.61 19.80
2. 1.62 19.90
3. 22 22 26 22 23 24
4. 23 30 33 22 27 33
5. 28 34 38 26 34 38
|
1518b-2t2c-eth-
l2bdbasemaclrn-oacl50sf-10kflows-ndrpdr
|
1. 1.41 17.39
2. 1.62 19.90
3. 22 23 26 22 23 26
4. 22 29 31 22 29 31
5. 23 30 33 23 29 32
|
1518b-4t4c-eth-
l2bdbasemaclrn-oacl50sf-10kflows-ndrpdr
|
1. 1.55 19.02
2. 1.62 19.90
3. 22 23 23 22 23 23
4. 22 28 30 22 28 30
5. 22 28 31 21 25 31
|
imix-1t1c-eth-
l2bdbasemaclrn-oacl50sf-10kflows-ndrpdr
|
1. 5.02 15.01
2. 5.12 15.31
|
imix-2t2c-eth-
l2bdbasemaclrn-oacl50sf-10kflows-ndrpdr
|
1. 4.76 14.24
2. 6.65 19.90
|
imix-4t4c-eth-
l2bdbasemaclrn-oacl50sf-10kflows-ndrpdr
|
1. 4.55 13.61
2. 6.65 19.90
|
10ge2p1vic1227-eth-l2bdbasemaclrn-oacl50sl-100flows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Cisco-VIC-1227.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100 flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-1t1c-eth-
l2bdbasemaclrn-oacl50sl-100flows-ndrpdr
|
1. 5.07 3.41
2. 5.13 3.44
3. 17 25 57 17 35 89
4. 25 66 87 26 77 90
5. 61 90 107 65 90 104
|
64b-2t2c-eth-
l2bdbasemaclrn-oacl50sl-100flows-ndrpdr
|
1. 9.48 6.37
2. 10.32 6.93
3. 18 43 54 18 42 51
4. 27 47 55 30 47 56
5. 55 67 74 53 65 75
|
64b-4t4c-eth-
l2bdbasemaclrn-oacl50sl-100flows-ndrpdr
|
1. 13.39 9.00
2. 17.10 11.49
3. 15 21 31 18 20 28
4. 28 40 45 25 37 42
5. 45 76 134 37 54 82
|
1518b-1t1c-eth-
l2bdbasemaclrn-oacl50sl-100flows-ndrpdr
|
1. 1.61 19.80
2. 1.62 19.90
3. 22 22 25 22 22 24
4. 23 33 36 22 29 36
5. 27 31 35 26 33 38
|
1518b-2t2c-eth-
l2bdbasemaclrn-oacl50sl-100flows-ndrpdr
|
1. 1.55 19.12
2. 1.62 19.90
3. 22 22 23 22 22 23
4. 22 25 28 22 25 28
5. 23 30 32 23 27 32
|
1518b-4t4c-eth-
l2bdbasemaclrn-oacl50sl-100flows-ndrpdr
|
1. 1.56 19.21
2. 1.62 19.90
3. 22 23 25 22 23 25
4. 22 26 28 22 26 29
5. 22 29 31 22 26 29
|
imix-1t1c-eth-
l2bdbasemaclrn-oacl50sl-100flows-ndrpdr
|
1. 4.82 14.41
2. 5.09 15.22
|
imix-2t2c-eth-
l2bdbasemaclrn-oacl50sl-100flows-ndrpdr
|
1. 4.64 13.89
2. 6.65 19.90
|
imix-4t4c-eth-
l2bdbasemaclrn-oacl50sl-100flows-ndrpdr
|
1. 4.26 12.75
2. 6.65 19.90
|
10ge2p1vic1227-eth-l2bdbasemaclrn-oacl50sl-100kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Cisco-VIC-1227.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-1t1c-eth-
l2bdbasemaclrn-oacl50sl-100kflows-ndrpdr
|
1. 5.08 3.42
2. 5.11 3.43
3. 17 22 53 17 25 72
4. 27 73 96 24 85 95
5. 67 95 116 76 102 114
|
64b-2t2c-eth-
l2bdbasemaclrn-oacl50sl-100kflows-ndrpdr
|
1. 9.24 6.21
2. 10.31 6.93
3. 18 44 53 18 34 49
4. 25 46 54 24 45 52
5. 56 67 75 54 65 71
|
64b-4t4c-eth-
l2bdbasemaclrn-oacl50sl-100kflows-ndrpdr
|
1. 13.33 8.96
2. 16.57 11.14
3. 17 23 29 17 22 30
4. 20 25 29 24 30 35
5. 39 53 73 38 57 161
|
1518b-1t1c-eth-
l2bdbasemaclrn-oacl50sl-100kflows-ndrpdr
|
1. 1.59 19.60
2. 1.62 19.90
3. 22 25 30 22 25 30
4. 22 30 34 22 26 33
5. 29 35 39 26 30 34
|
1518b-2t2c-eth-
l2bdbasemaclrn-oacl50sl-100kflows-ndrpdr
|
1. 1.59 19.51
2. 1.62 19.90
3. 22 23 26 22 23 26
4. 22 26 28 22 23 27
5. 23 30 32 22 30 32
|
1518b-4t4c-eth-
l2bdbasemaclrn-oacl50sl-100kflows-ndrpdr
|
1. 1.46 17.92
2. 1.62 19.90
3. 22 23 23 22 23 23
4. 22 27 29 22 26 29
5. 22 29 32 21 25 28
|
imix-1t1c-eth-
l2bdbasemaclrn-oacl50sl-100kflows-ndrpdr
|
1. 5.08 15.19
2. 5.13 15.35
|
imix-2t2c-eth-
l2bdbasemaclrn-oacl50sl-100kflows-ndrpdr
|
1. 4.86 14.52
2. 6.65 19.90
|
imix-4t4c-eth-
l2bdbasemaclrn-oacl50sl-100kflows-ndrpdr
|
1. 4.51 13.48
2. 6.65 19.90
|
10ge2p1vic1227-eth-l2bdbasemaclrn-oacl50sl-10kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Cisco-VIC-1227.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-1t1c-eth-
l2bdbasemaclrn-oacl50sl-10kflows-ndrpdr
|
1. 5.09 3.42
2. 5.12 3.44
3. 17 28 61 17 27 92
4. 32 69 81 33 71 90
5. 68 103 123 78 105 119
|
64b-2t2c-eth-
l2bdbasemaclrn-oacl50sl-10kflows-ndrpdr
|
1. 9.23 6.21
2. 10.21 6.86
3. 18 50 60 18 32 55
4. 41 62 70 34 58 67
5. 55 67 77 54 66 76
|
64b-4t4c-eth-
l2bdbasemaclrn-oacl50sl-10kflows-ndrpdr
|
1. 13.36 8.98
2. 17.95 12.06
3. 18 22 27 18 19 24
4. 20 24 30 18 23 28
5. 42 59 89 44 84 149
|
1518b-1t1c-eth-
l2bdbasemaclrn-oacl50sl-10kflows-ndrpdr
|
1. 1.59 19.51
2. 1.62 19.90
3. 22 25 31 22 24 31
4. 27 33 36 25 33 36
5. 27 35 38 25 30 35
|
1518b-2t2c-eth-
l2bdbasemaclrn-oacl50sl-10kflows-ndrpdr
|
1. 1.62 19.90
2. 1.62 19.90
3. 22 23 27 22 23 26
4. 23 27 29 22 24 27
5. 23 30 32 23 30 33
|
1518b-4t4c-eth-
l2bdbasemaclrn-oacl50sl-10kflows-ndrpdr
|
1. 1.58 19.41
2. 1.62 19.90
3. 22 23 29 22 23 30
4. 22 26 28 22 26 29
5. 22 27 29 21 26 29
|
imix-1t1c-eth-
l2bdbasemaclrn-oacl50sl-10kflows-ndrpdr
|
1. 5.06 15.15
2. 5.12 15.30
|
imix-2t2c-eth-
l2bdbasemaclrn-oacl50sl-10kflows-ndrpdr
|
1. 4.55 13.61
2. 6.65 19.90
|
imix-4t4c-eth-
l2bdbasemaclrn-oacl50sl-10kflows-ndrpdr
|
1. 4.74 14.17
2. 6.65 19.90
|
10ge2p1vic1227-eth-l2bdscale100kmaclrn-ndrpdr
RFC2544: Pkt throughput for L2BD test cases
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4 for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 bridge- domain and MAC learning enabled. DUT1 and DUT2 tested with Cisco-VIC-1227.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 50k flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses ranges are incremented as follows: port01_src ca:fe:00:00:00:00 - port01_src ca:fe:00:07:a1:1f, port01_dst fa:ce:00:00:00:00 - port01_dst fa:ce:00:07:a1:1f, port02_src fa:ce:00:00:00:00 - port02_src fa:ce:00:07:a1:1f, port02_dst ca:fe:00:00:00:00 - port02_dst ca:fe:00:07:a1:1f
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-1t1c-
eth-l2bdscale100kmaclrn-ndrpdr
|
1. 6.01 4.04
2. 7.05 4.74
3. 17 41 54 17 42 53
4. 35 59 70 30 58 69
5. 95 141 177 92 134 169
|
64b-2t2c-
eth-l2bdscale100kmaclrn-ndrpdr
|
1. 11.17 7.51
2. 13.44 9.03
3. 18 37 47 18 35 45
4. 29 40 49 26 35 44
5. 59 75 84 51 64 74
|
64b-4t4c-
eth-l2bdscale100kmaclrn-ndrpdr
|
1. 13.83 9.29
2. 18.95 12.73
3. 17 20 23 17 19 23
4. 19 24 30 18 24 29
5. 27 33 39 26 32 38
|
1518b-1t1c-
eth-l2bdscale100kmaclrn-ndrpdr
|
1. 1.61 19.80
2. 1.62 19.90
3. 22 23 25 22 23 25
4. 22 30 32 22 27 31
5. 26 31 34 24 31 36
|
1518b-2t2c-
eth-l2bdscale100kmaclrn-ndrpdr
|
1. 1.62 19.90
2. 1.62 19.90
3. 22 23 28 22 23 29
4. 22 26 29 21 23 29
5. 21 25 30 21 25 28
|
1518b-4t4c-
eth-l2bdscale100kmaclrn-ndrpdr
|
1. 1.62 19.90
2. 1.62 19.90
3. 22 22 25 22 22 24
4. 22 24 26 21 23 25
5. 21 28 31 21 25 27
|
imix-1t1c-
eth-l2bdscale100kmaclrn-ndrpdr
|
1. 5.20 15.56
2. 6.65 19.89
|
imix-2t2c-
eth-l2bdscale100kmaclrn-ndrpdr
|
1. 4.69 14.02
2. 6.65 19.90
|
imix-4t4c-
eth-l2bdscale100kmaclrn-ndrpdr
|
1. 4.78 14.31
2. 6.65 19.90
|
10ge2p1vic1227-eth-l2bdscale10kmaclrn-ndrpdr
RFC2544: Pkt throughput for L2BD test cases
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4 for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 bridge- domain and MAC learning enabled. DUT1 and DUT2 tested with Cisco-VIC-1227.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 5k flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses ranges are incremented as follows: port01_src ca:fe:00:00:00:00 - port01_src ca:fe:00:07:a1:1f, port01_dst fa:ce:00:00:00:00 - port01_dst fa:ce:00:07:a1:1f, port02_src fa:ce:00:00:00:00 - port02_src fa:ce:00:07:a1:1f, port02_dst ca:fe:00:00:00:00 - port02_dst ca:fe:00:07:a1:1f
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-1t1c-
eth-l2bdscale10kmaclrn-ndrpdr
|
1. 6.57 4.41
2. 7.98 5.36
3. 17 32 42 17 25 35
4. 33 43 49 18 21 31
5. 82 101 116 82 103 116
|
64b-2t2c-
eth-l2bdscale10kmaclrn-ndrpdr
|
1. 12.36 8.31
2. 15.48 10.40
3. 17 24 38 17 22 31
4. 24 44 51 26 44 58
5. 54 62 70 51 59 67
|
64b-4t4c-
eth-l2bdscale10kmaclrn-ndrpdr
|
1. 13.92 9.35
2. 19.26 12.94
3. 17 18 23 17 18 22
4. 22 30 34 20 29 33
5. 24 29 35 24 29 33
|
1518b-1t1c-
eth-l2bdscale10kmaclrn-ndrpdr
|
1. 1.62 19.90
2. 1.62 19.90
3. 22 22 28 22 22 27
4. 22 29 31 22 26 29
5. 26 33 37 25 32 35
|
1518b-2t2c-
eth-l2bdscale10kmaclrn-ndrpdr
|
1. 1.62 19.90
2. 1.62 19.90
3. 22 22 27 22 22 26
4. 22 25 28 21 23 26
5. 22 29 32 22 27 30
|
1518b-4t4c-
eth-l2bdscale10kmaclrn-ndrpdr
|
1. 1.62 19.90
2. 1.62 19.90
3. 22 22 26 22 22 25
4. 22 24 26 22 23 26
5. 21 28 31 21 24 26
|
imix-1t1c-
eth-l2bdscale10kmaclrn-ndrpdr
|
1. 5.03 15.04
2. 6.65 19.90
|
imix-2t2c-
eth-l2bdscale10kmaclrn-ndrpdr
|
1. 4.24 12.69
2. 6.65 19.90
|
imix-4t4c-
eth-l2bdscale10kmaclrn-ndrpdr
|
1. 4.64 13.88
2. 6.65 19.90
|
10ge2p1vic1227-eth-l2bdscale1mmaclrn-ndrpdr
RFC2544: Pkt throughput for L2BD test cases
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4 for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 bridge- domain and MAC learning enabled. DUT1 and DUT2 tested with Cisco-VIC-1227.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 500k flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses ranges are incremented as follows: port01_src ca:fe:00:00:00:00 - port01_src ca:fe:00:07:a1:1f, port01_dst fa:ce:00:00:00:00 - port01_dst fa:ce:00:07:a1:1f, port02_src fa:ce:00:00:00:00 - port02_src fa:ce:00:07:a1:1f, port02_dst ca:fe:00:00:00:00 - port02_dst ca:fe:00:07:a1:1f
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-1t1c-
eth-l2bdscale1mmaclrn-ndrpdr
|
1. 5.97 4.01
2. 6.77 4.55
3. 17 40 65 17 38 63
4. 24 68 80 26 68 79
5. 101 139 159 101 139 160
|
64b-2t2c-
eth-l2bdscale1mmaclrn-ndrpdr
|
1. 11.00 7.39
2. 12.85 8.63
3. 17 39 55 17 20 45
4. 43 66 76 41 66 75
5. 66 78 91 64 77 88
|
64b-4t4c-
eth-l2bdscale1mmaclrn-ndrpdr
|
1. 13.50 9.07
2. 18.87 12.68
3. 17 18 22 18 18 21
4. 26 36 40 24 35 38
5. 33 41 49 31 38 45
|
1518b-1t1c-
eth-l2bdscale1mmaclrn-ndrpdr
|
1. 1.62 19.90
2. 1.62 19.90
3. 22 22 28 22 22 26
4. 22 29 32 22 26 31
5. 26 34 38 25 30 38
|
1518b-2t2c-
eth-l2bdscale1mmaclrn-ndrpdr
|
1. 1.62 19.90
2. 1.62 19.90
3. 22 22 24 22 22 23
4. 22 25 27 21 23 25
5. 22 29 32 22 27 31
|
1518b-4t4c-
eth-l2bdscale1mmaclrn-ndrpdr
|
1. 1.60 19.70
2. 1.62 19.90
3. 22 22 25 22 22 23
4. 22 25 27 22 24 26
5. 21 28 32 21 25 26
|
imix-1t1c-
eth-l2bdscale1mmaclrn-ndrpdr
|
1. 5.31 15.87
2. 6.37 19.04
|
imix-2t2c-
eth-l2bdscale1mmaclrn-ndrpdr
|
1. 4.99 14.93
2. 6.65 19.89
|
imix-4t4c-
eth-l2bdscale1mmaclrn-ndrpdr
|
1. 4.77 14.27
2. 6.65 19.87
|
10ge2p1vic1227-eth-l2patch-ndrpdr
RFC2544: Pkt throughput L2patch test cases
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4 for L2 patch.
[Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 patch DUT1 and DUT2 tested with Cisco-VIC-1227.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 254 flows per flow-group) with all packets containing Ethernet header,IPv4 header with static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-1t1c-eth-l2patch-ndrpdr
|
1. 13.63 9.16
2. 18.48 12.42
3. 14 17 19 16 17 20
4. 19 23 29 19 23 29
5. 43 50 58 45 53 61
|
64b-2t2c-eth-l2patch-ndrpdr
|
1. 14.10 9.48
2. 19.22 12.92
3. 16 17 18 17 17 17
4. 14 18 21 14 18 21
5. 20 23 27 19 23 27
|
64b-4t4c-eth-l2patch-ndrpdr
|
1. 15.02 10.09
2. 19.29 12.96
3. 14 16 17 16 17 18
4. 13 17 20 13 17 19
5. 15 18 22 14 18 21
|
1518b-1t1c-eth-l2patch-ndrpdr
|
1. 1.59 19.51
2. 1.62 19.90
3. 21 22 28 21 23 28
4. 21 26 29 21 26 30
5. 21 23 27 20 23 26
|
1518b-2t2c-eth-l2patch-ndrpdr
|
1. 1.62 19.90
2. 1.62 19.90
3. 21 21 25 21 21 24
4. 21 26 28 21 26 28
5. 21 28 30 20 24 26
|
1518b-4t4c-eth-l2patch-ndrpdr
|
1. 1.56 19.21
2. 1.62 19.90
3. 21 21 23 21 21 22
4. 21 21 24 20 21 24
5. 20 26 29 19 23 25
|
imix-1t1c-eth-l2patch-ndrpdr
|
1. 4.60 13.75
2. 6.65 19.90
|
imix-2t2c-eth-l2patch-ndrpdr
|
1. 4.88 14.60
2. 6.65 19.90
|
imix-4t4c-eth-l2patch-ndrpdr
|
1. 4.53 13.54
2. 6.65 19.90
|
10ge2p1vic1227-eth-l2xcbase-ndrpdr
RFC2544: Pkt throughput L2XC test cases
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4 for L2 cross connect.
[Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 cross- connect. DUT1 and DUT2 tested with Cisco-VIC-1227.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-1t1c-eth-l2xcbase-ndrpdr
|
1. 10.68 7.18
2. 13.58 9.13
3. 17 21 24 17 22 25
4. 20 31 35 21 31 36
5. 60 71 82 58 71 83
|
64b-2t2c-eth-l2xcbase-ndrpdr
|
1. 13.77 9.25
2. 18.77 12.62
3. 15 17 20 17 17 21
4. 18 26 31 18 25 30
5. 26 30 36 24 29 34
|
64b-4t4c-eth-l2xcbase-ndrpdr
|
1. 13.61 9.15
2. 19.63 13.19
3. 16 18 19 16 18 19
4. 14 17 20 14 17 19
5. 18 21 24 18 21 24
|
1518b-1t1c-eth-l2xcbase-ndrpdr
|
1. 1.55 19.02
2. 1.62 19.90
3. 21 23 26 21 23 27
4. 24 30 33 22 27 31
5. 24 30 33 22 30 33
|
1518b-2t2c-eth-l2xcbase-ndrpdr
|
1. 1.59 19.51
2. 1.62 19.90
3. 21 22 22 21 22 22
4. 22 26 29 21 25 29
5. 21 24 27 21 24 27
|
1518b-4t4c-eth-l2xcbase-ndrpdr
|
1. 1.43 17.65
2. 1.62 19.90
3. 21 22 23 21 22 23
4. 21 23 26 21 22 26
5. 20 26 28 19 25 28
|
imix-1t1c-eth-l2xcbase-ndrpdr
|
1. 4.69 14.02
2. 6.65 19.90
|
imix-2t2c-eth-l2xcbase-ndrpdr
|
1. 4.90 14.67
2. 6.65 19.90
|
imix-4t4c-eth-l2xcbase-ndrpdr
|
1. 4.46 13.34
2. 6.65 19.90
|