func

ip4 tunnels

lisp

eth2p-ethip4lisp-ip4base-func

IP AFI independent functional tests.

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv4-LISP-IPv4-ICMPv4 on DUT1-DUT2, Eth-IPv4-ICMPv4 on TG-DUTn for IPv4 routing over LISPoIPv4 tunnel.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv4 routing and static routes. LISPoIPv4 tunnel is configured between DUT1 and DUT2.
  • [Ver] TG verification: Test ICMPv4 Echo Request packets are sent in both directions by TG on links to DUT1 and DUT2; on receive TG verifies packets for correctness and their IPv4 src-addr, dst-addr and MAC addresses.
  • [Ref] Applicable standard specifications: RFC6830.
Name Documentation Status
tc01: dut1 and dut2 route ipv4 over lispoipv4 tunnel after disable-enable [Top] TG-DUT1-DUT2-TG.
[Enc] Eth-IPv4-LISP-IPv4-ICMPv4 on DUT1-DUT2, Eth-IPv4-ICMPv4 on TG-DUTn.
[Cfg1] On DUT1 and DUT2 configure IPv4 LISP static adjacencies.
[Ver1] Make TG send ICMPv4 Echo Req between its interfaces across both DUTs and LISP tunnel between them; verify IPv4 headers on received packets are correct.
[Cfg2] Disable LISP.
[Ver2] Verify packets are not received via LISP tunnel.
[Cfg3] Re-enable LISP.
[Ver3] Verify packets are received again via LISP tunnel.
[Ref] RFC6830.
PASS

eth2p-ethip4lispgpe-ip4base-func

ip4-lispgpe-ip4 encapsulation test cases

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv4-LISP-IPv4-ICMPv4 on DUT1-DUT2, Eth-IPv4-ICMPv4 on TG-DUTn for IPv4 routing over LISPoIPv4 tunnel.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv4 routing and static routes. LISPoIPv4 tunnel is configured between DUT1 and DUT2.
  • [Ver] TG verification: Test ICMPv4 Echo Request packets are sent in both directions by TG on links to DUT1 and DUT2; on receive TG verifies packets for correctness and their IPv4 src-addr, dst-addr and MAC addresses.
  • [Ref] Applicable standard specifications: RFC6830.
Name Documentation Status
tc01: dut1 and dut2 route ipv4 bidirectionally over lisp gpe tunnel using physical interfaces [Top] TG-DUT1-DUT2-TG.
[Enc] Eth-IPv4-LISPGPE-IPv4-ICMPv4 on DUT1-DUT2, Eth-IPv4-ICMPv4 on TG-DUTn.
[Cfg] Configure IPv4 LISP static adjacencies on DUT1 and DUT2.
[Ver] Case: ip4-lispgpe-ip4 - phy2lisp Make TG send ICMPv4 Echo Req between its interfaces across both DUTs and LISP GPE tunnel between them; verify IPv4 headers on received packets are correct.
[Ref] RFC6830.
PASS

eth2p-ethip4lispgpe-ip6base-func

LISP static adjacency test cases

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv4-LISP-IPv6-ICMPv6 on DUT1-DUT2, Eth-IPv6-ICMPv6 on TG-DUTn for IPv6 routing over LISPoIPv4 tunnel.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv6 routing and static routes. LISPoIPv4 tunnel is configured between DUT1 and DUT2.
  • [Ver] TG verification: Test ICMPv6 Echo Request packets are sent in both directions by TG on links to DUT1 and DUT2; on receive TG verifies packets for correctness and their IPv6 src-addr, dst-addr and MAC addresses.
  • [Ref] Applicable standard specifications: RFC6830.
Name Documentation Status
tc01: dut1 and dut2 route ipv6 bidirectionally over lispoipv4 tunnel [Top] TG-DUT1-DUT2-TG.
[Enc] Eth-IPv4-LISP-IPv6-ICMPv6 on DUT1-DUT2, Eth-IPv6-ICMPv6 on TG-DUTn.
[Cfg] On DUT1 and DUT2 configure IPv4 LISP static adjacencies.
[Ver] Make TG send ICMPv6 Echo Req between its interfaces across both DUTs and LISP tunnel between them; verify IPv6 headers on received packets are correct.
[Cfg2] Reconf LISP.
[Ver2] Verify packets are received again via LISP tunnel.
[Ref] RFC6830.
PASS

ip6 tunnels

lisp

eth2p-ethip6lispgpe-ip4base-func

LISP static adjacency test cases

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv6-LISP-IPv4-ICMPv4 on DUT1-DUT2, Eth-IPv4-ICMPv4 on TG-DUTn for IPv4 routing over LISPoIPv6 tunnel.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv4 routing and static routes. LISPoIPv6 tunnel is configured between DUT1 and DUT2.
  • [Ver] TG verification: Test ICMPv4 Echo Request packets are sent in both directions by TG on links to DUT1 and DUT2; on receive TG verifies packets for correctness and their IPv4 src-addr, dst-addr and MAC addresses.
  • [Ref] Applicable standard specifications: RFC6830.
Name Documentation Status
tc01: dut1 and dut2 route ipv4 bidirectionally over lispoipv6 tunnel [Top] TG-DUT1-DUT2-TG.
[Enc] Eth-IPv6-LISP-IPv4-ICMPv4 on DUT1-DUT2, Eth-IPv4-ICMPv4 on TG-DUTn.
[Cfg] On DUT1 and DUT2 configure IPv6 LISP static adjacencies.
[Ver] Make TG send ICMPv4 Echo Req between its interfaces across both DUTs and LISP tunnel between them; verify IPv4 headers on received packets are correct.
[Cfg2] Reconf LISP.
[Ver2] Verify packets are received again via LISP tunnel.
[Ref] RFC6830.
PASS

eth2p-ethip6lispgpe-ip6base-func

ip6-lispgpe-ip6 encapsulation test cases

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv6-LISP-IPv6-ICMPv6 on DUT1-DUT2, Eth-IPv6-ICMPv6 on TG-DUTn for IPv6 routing over LISPoIPv6 tunnel.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv6 routing and static routes. LISPoIPv6 tunnel is configured between DUT1 and DUT2.
  • [Ver] TG verification: Test ICMPv6 Echo Request packets are sent in both directions by TG on links to DUT1 and DUT2; on receive TG verifies packets for correctness and their IPv6 src-addr, dst-addr and MAC addresses.
  • [Ref] Applicable standard specifications: RFC6830.
Name Documentation Status
tc01: dut1 and dut2 route ipv6 bidirectionally over lisp gpe tunnel using physical interfaces [Top] TG-DUT1-DUT2-TG.
[Enc] Eth-IPv6-LISPGPE-IPv6-ICMPv6 on DUT1-DUT2, Eth-IPv6-ICMPv6 on TG-DUTn.
[Cfg] Configure IPv6 LISP static adjacencies on DUT1 and DUT2.
[Ver] Case: ip6-lispgpe-ip6 - phy2lisp Make TG send ICMPv6 Echo Req between its interfaces across both DUTs and LISP GPE tunnel between them; verify IPv6 headers on received packets are correct.
[Ref] RFC6830.
PASS

l2xc

eth2p-dot1ad-l2xcbase-func

L2 cross-connect with QinQ test cases

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet encapsulations: Eth-dot1ad-IPv4-ICMPv4 on DUT1-DUT2, Eth-IPv4-ICMPv4 on TG-DUTn for L2 switching of IPv4.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 cross-connect (L2XC) switching with 802.1ad QinQ VLAN tag push and pop.
  • [Ver] TG verification: Test ICMPv4 Echo Request packets are sent in both directions by TG on links to DUT1 and DUT2; on receive TG verifies packets for correctness and their IPv4 src-addr, dst-addr and MAC addresses.
  • [Ref] Applicable standard specifications: IEEE 802.1ad.
Name Documentation Status
tc01: dut1 and dut2 with l2xc and two vlan push-pop switch icmpv4 between two tg links [Top] TG-DUT1-DUT2-TG.
[Enc] Eth-dot1ad-IPv4-ICMPv4 on DUT1-DUT2, Eth-IPv4-ICMPv4 on TG-DUTn.
[Cfg] On DUT1 and DUT2 configure L2 cross-connect (L2XC), each with one interface to TG and one Ethernet interface towards the other DUT; each DUT pushes two VLAN tags on packets received from local TG, and popping two VLAN tags on packets transmitted to local TG.
[Ver] Make TG send ICMPv4 Echo Req in both directions between two of its interfaces to be switched by DUT1 and DUT2; verify all packets are received.
[Ref] IEEE 802.1ad.
PASS