.. |br| raw:: html
.. |prein| raw:: html
.. |preout| raw:: html
container memif
---------------
10ge2p1x520-eth-l2bdbasemaclrn-eth-2memif-1lxc-mrr
``````````````````````````````````````````````````
**Raw results L2BD test cases**
- **[Top] Network Topologies:** TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- **[Enc] Packet Encapsulations:** Eth-IPv4 for L2 bridge domain.
- **[Cfg] DUT configuration:** DUT1 and DUT2 are configured with two L2 bridge domains and MAC learning enabled. LXC is connected to VPP via Memif interface. LXC is running same VPP version as running on DUT. LXC is limited via cgroup to use 3 cores allocated from pool of isolated CPUs. There are no memory constraints. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.
- **[Ver] TG verification:** In MaxReceivedRate test TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 254 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
.. only:: html
.. csv-table::
:header-rows: 1
:widths: auto
:align: center
:file: vpp_mrr_results_10ge2p1x520-eth-l2bdbasemaclrn-eth-2memif-1lxc-mrr.csv
.. only:: latex
.. raw:: latex
\csvautolongtable{_tmp/src/detailed_test_results/vpp_mrr_results/vpp_mrr_results_10ge2p1x520-eth-l2bdbasemaclrn-eth-2memif-1lxc-mrr.csv}
10ge2p1x520-eth-l2xcbase-eth-2memif-1dcr-mrr
````````````````````````````````````````````
**Raw results L2XC test cases**
- **[Top] Network Topologies:** TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- **[Enc] Packet Encapsulations:** Eth-IPv4 for L2 cross connect.
- **[Cfg] DUT configuration:** DUT1 and DUT2 are configured with L2 cross- connect. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel. Container is connected to VPP via Memif interface. Container is running same VPP version as running on DUT. Container is limited via cgroup to use 3 cores allocated from pool of isolated CPUs. There are no memory contraints.
- **[Ver] TG verification:** In MaxReceivedRate test TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 254 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
.. only:: html
.. csv-table::
:header-rows: 1
:widths: auto
:align: center
:file: vpp_mrr_results_10ge2p1x520-eth-l2xcbase-eth-2memif-1dcr-mrr.csv
.. only:: latex
.. raw:: latex
\csvautolongtable{_tmp/src/detailed_test_results/vpp_mrr_results/vpp_mrr_results_10ge2p1x520-eth-l2xcbase-eth-2memif-1dcr-mrr.csv}
10ge2p1x520-eth-l2xcbase-eth-2memif-1lxc-mrr
````````````````````````````````````````````
**Raw results L2XC test cases**
- **[Top] Network Topologies:** TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- **[Enc] Packet Encapsulations:** Eth-IPv4 for L2 cross connect.
- **[Cfg] DUT configuration:** DUT1 and DUT2 are configured with L2 cross- connect. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel. LXC is connected to VPP via Memif interface. LXC is running same VPP version as running on DUT. LXC is limited via cgroup to use 3 cores allocated from pool of isolated CPUs. There are no memory contraints.
- **[Ver] TG verification:** In MaxReceivedRate test TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 254 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
.. only:: html
.. csv-table::
:header-rows: 1
:widths: auto
:align: center
:file: vpp_mrr_results_10ge2p1x520-eth-l2xcbase-eth-2memif-1lxc-mrr.csv
.. only:: latex
.. raw:: latex
\csvautolongtable{_tmp/src/detailed_test_results/vpp_mrr_results/vpp_mrr_results_10ge2p1x520-eth-l2xcbase-eth-2memif-1lxc-mrr.csv}
10ge2p1x710-eth-l2bdbasemaclrn-eth-2memif-1lxc-mrr
``````````````````````````````````````````````````
**Raw results L2BD test cases**
- **[Top] Network Topologies:** TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- **[Enc] Packet Encapsulations:** Eth-IPv4 for L2 bridge domain.
- **[Cfg] DUT configuration:** DUT1 and DUT2 are configured with two L2 bridge domains and MAC learning enabled. LXC is connected to VPP via Memif interface. LXC is running same VPP version as running on DUT. LXC is limited via cgroup to use 3 cores allocated from pool of isolated CPUs. There are no memory constraints. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel.
- **[Ver] TG verification:** In MaxReceivedRate test TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 254 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
.. only:: html
.. csv-table::
:header-rows: 1
:widths: auto
:align: center
:file: vpp_mrr_results_10ge2p1x710-eth-l2bdbasemaclrn-eth-2memif-1lxc-mrr.csv
.. only:: latex
.. raw:: latex
\csvautolongtable{_tmp/src/detailed_test_results/vpp_mrr_results/vpp_mrr_results_10ge2p1x710-eth-l2bdbasemaclrn-eth-2memif-1lxc-mrr.csv}
10ge2p1x710-eth-l2xcbase-eth-2memif-1dcr-mrr
````````````````````````````````````````````
**Raw results L2XC test cases**
- **[Top] Network Topologies:** TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- **[Enc] Packet Encapsulations:** Eth-IPv4 for L2 cross connect.
- **[Cfg] DUT configuration:** DUT1 and DUT2 are configured with L2 cross- connect. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel. Container is connected to VPP via Memif interface. Container is running same VPP version as running on DUT. Container is limited via cgroup to use 3 cores allocated from pool of isolated CPUs. There are no memory contraints.
- **[Ver] TG verification:** In MaxReceivedRate test TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 254 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
.. only:: html
.. csv-table::
:header-rows: 1
:widths: auto
:align: center
:file: vpp_mrr_results_10ge2p1x710-eth-l2xcbase-eth-2memif-1dcr-mrr.csv
.. only:: latex
.. raw:: latex
\csvautolongtable{_tmp/src/detailed_test_results/vpp_mrr_results/vpp_mrr_results_10ge2p1x710-eth-l2xcbase-eth-2memif-1dcr-mrr.csv}
10ge2p1x710-eth-l2xcbase-eth-2memif-1lxc-mrr
````````````````````````````````````````````
**Raw results L2XC test cases**
- **[Top] Network Topologies:** TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- **[Enc] Packet Encapsulations:** Eth-IPv4 for L2 cross connect.
- **[Cfg] DUT configuration:** DUT1 and DUT2 are configured with L2 cross- connect. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel. LXC is connected to VPP via Memif interface. LXC is running same VPP version as running on DUT. LXC is limited via cgroup to use 3 cores allocated from pool of isolated CPUs. There are no memory contraints.
- **[Ver] TG verification:** In MaxReceivedRate test TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 254 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
.. only:: html
.. csv-table::
:header-rows: 1
:widths: auto
:align: center
:file: vpp_mrr_results_10ge2p1x710-eth-l2xcbase-eth-2memif-1lxc-mrr.csv
.. only:: latex
.. raw:: latex
\csvautolongtable{_tmp/src/detailed_test_results/vpp_mrr_results/vpp_mrr_results_10ge2p1x710-eth-l2xcbase-eth-2memif-1lxc-mrr.csv}
40ge2p1xl710-eth-l2bdbasemaclrn-eth-2memif-1lxc-mrr
```````````````````````````````````````````````````
**Raw results L2BD test cases**
- **[Top] Network Topologies:** TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- **[Enc] Packet Encapsulations:** Eth-IPv4 for L2 bridge domain.
- **[Cfg] DUT configuration:** DUT1 and DUT2 are configured with two L2 bridge domains and MAC learning enabled. LXC is connected to VPP via Memif interface. LXC is running same VPP version as running on DUT. LXC is limited via cgroup to use 3 cores allocated from pool of isolated CPUs. There are no memory constraints. DUT1 and DUT2 tested with 2p40GE NIC XL710 by Intel.
- **[Ver] TG verification:** In MaxReceivedRate test TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 254 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
.. only:: html
.. csv-table::
:header-rows: 1
:widths: auto
:align: center
:file: vpp_mrr_results_40ge2p1xl710-eth-l2bdbasemaclrn-eth-2memif-1lxc-mrr.csv
.. only:: latex
.. raw:: latex
\csvautolongtable{_tmp/src/detailed_test_results/vpp_mrr_results/vpp_mrr_results_40ge2p1xl710-eth-l2bdbasemaclrn-eth-2memif-1lxc-mrr.csv}
40ge2p1xl710-eth-l2xcbase-eth-2memif-1lxc-mrr
`````````````````````````````````````````````
**Raw results L2XC test cases**
- **[Top] Network Topologies:** TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- **[Enc] Packet Encapsulations:** Eth-IPv4 for L2 cross connect.
- **[Cfg] DUT configuration:** DUT1 and DUT2 are configured with L2 cross- connect. DUT1 and DUT2 tested with 2p40GE NIC XL710 by Intel. LXC is connected to VPP via Memif interface. LXC is running same VPP version as running on DUT. LXC is limited via cgroup to use 3 cores allocated from pool of isolated CPUs. There are no memory contraints.
- **[Ver] TG verification:** In MaxReceivedRate test TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 254 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
.. only:: html
.. csv-table::
:header-rows: 1
:widths: auto
:align: center
:file: vpp_mrr_results_40ge2p1xl710-eth-l2xcbase-eth-2memif-1lxc-mrr.csv
.. only:: latex
.. raw:: latex
\csvautolongtable{_tmp/src/detailed_test_results/vpp_mrr_results/vpp_mrr_results_40ge2p1xl710-eth-l2xcbase-eth-2memif-1lxc-mrr.csv}
crypto
------
40ge2p1xl710-ethip4ipsecbasetnl-ip4base-int-aes-gcm-mrr
```````````````````````````````````````````````````````
**Raw results IPv4 IPsec tunnel mode performance test suite.**
- **[Top] Network Topologies:** TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- **[Enc] Packet Encapsulations:** Eth-IPv4 on TG-DUTn, Eth-IPv4-IPSec on DUT1-DUT2
- **[Cfg] DUT configuration:** DUT1 and DUT2 are configured with multiple IPsec tunnels between them. DUTs get IPv4 traffic from TG, encrypt it and send to another DUT, where packets are decrypted and sent back to TG
- **[Ver] TG verification:** In MaxReceivedRate test TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, number of flows per flow-group equals to number of IPSec tunnels) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv4 destination address) field is applied to both streams.
- **[Ref] Applicable standard specifications:** RFC4303 and RFC2544.
.. only:: html
.. csv-table::
:header-rows: 1
:widths: auto
:align: center
:file: vpp_mrr_results_40ge2p1xl710-ethip4ipsecbasetnl-ip4base-int-aes-gcm-mrr.csv
.. only:: latex
.. raw:: latex
\csvautolongtable{_tmp/src/detailed_test_results/vpp_mrr_results/vpp_mrr_results_40ge2p1xl710-ethip4ipsecbasetnl-ip4base-int-aes-gcm-mrr.csv}
40ge2p1xl710-ethip4ipsecbasetnl-ip4base-int-cbc-sha1-mrr
````````````````````````````````````````````````````````
**Raw results IPv4 IPsec tunnel mode performance test suite.**
- **[Top] Network Topologies:** TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- **[Enc] Packet Encapsulations:** Eth-IPv4 on TG-DUTn, Eth-IPv4-IPSec on DUT1-DUT2
- **[Cfg] DUT configuration:** DUT1 and DUT2 are configured with multiple IPsec tunnels between them. DUTs get IPv4 traffic from TG, encrypt it and send to another DUT, where packets are decrypted and sent back to TG
- **[Ver] TG verification:** In MaxReceivedRate test TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, number of flows per flow-group equals to number of IPSec tunnels) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv4 destination address) field is applied to both streams.
- **[Ref] Applicable standard specifications:** RFC4303 and RFC2544.
.. only:: html
.. csv-table::
:header-rows: 1
:widths: auto
:align: center
:file: vpp_mrr_results_40ge2p1xl710-ethip4ipsecbasetnl-ip4base-int-cbc-sha1-mrr.csv
.. only:: latex
.. raw:: latex
\csvautolongtable{_tmp/src/detailed_test_results/vpp_mrr_results/vpp_mrr_results_40ge2p1xl710-ethip4ipsecbasetnl-ip4base-int-cbc-sha1-mrr.csv}
40ge2p1xl710-ethip4ipsecbasetnlsw-ip4base-int-aes-gcm-mrr
`````````````````````````````````````````````````````````
**Raw results IPv4 IPsec tunnel mode performance test suite.**
- **[Top] Network Topologies:** TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- **[Enc] Packet Encapsulations:** Eth-IPv4 on TG-DUTn, Eth-IPv4-IPSec on DUT1-DUT2
- **[Cfg] DUT configuration:** DUT1 and DUT2 are configured with DPDK SW crypto devices and multiple IPsec tunnels between them. DUTs get IPv4 traffic from TG, encrypt it and send to another DUT, where packets are decrypted and sent back to TG
- **[Ver] TG verification:** In MaxReceivedRate test TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, number of flows per flow-group equals to number of IPSec tunnels) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv4 destination address) field is applied to both streams.
- **[Ref] Applicable standard specifications:** RFC4303 and RFC2544.
.. only:: html
.. csv-table::
:header-rows: 1
:widths: auto
:align: center
:file: vpp_mrr_results_40ge2p1xl710-ethip4ipsecbasetnlsw-ip4base-int-aes-gcm-mrr.csv
.. only:: latex
.. raw:: latex
\csvautolongtable{_tmp/src/detailed_test_results/vpp_mrr_results/vpp_mrr_results_40ge2p1xl710-ethip4ipsecbasetnlsw-ip4base-int-aes-gcm-mrr.csv}
40ge2p1xl710-ethip4ipsecbasetnlsw-ip4base-int-cbc-sha1-mrr
``````````````````````````````````````````````````````````
**Raw results IPv4 IPsec tunnel mode performance test suite.**
- **[Top] Network Topologies:** TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- **[Enc] Packet Encapsulations:** Eth-IPv4 on TG-DUTn, Eth-IPv4-IPSec on DUT1-DUT2
- **[Cfg] DUT configuration:** DUT1 and DUT2 are configured with DPDK SW crypto devices and multiple IPsec tunnels between them. DUTs get IPv4 traffic from TG, encrypt it and send to another DUT, where packets are decrypted and sent back to TG
- **[Ver] TG verification:** In MaxReceivedRate test TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, number of flows per flow-group equals to number of IPSec tunnels) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv4 destination address) field is applied to both streams.
- **[Ref] Applicable standard specifications:** RFC4303 and RFC2544.
.. only:: html
.. csv-table::
:header-rows: 1
:widths: auto
:align: center
:file: vpp_mrr_results_40ge2p1xl710-ethip4ipsecbasetnlsw-ip4base-int-cbc-sha1-mrr.csv
.. only:: latex
.. raw:: latex
\csvautolongtable{_tmp/src/detailed_test_results/vpp_mrr_results/vpp_mrr_results_40ge2p1xl710-ethip4ipsecbasetnlsw-ip4base-int-cbc-sha1-mrr.csv}
40ge2p1xl710-ethip4ipsecscale1000tnl-ip4base-int-aes-gcm-mrr
````````````````````````````````````````````````````````````
**Raw results IPv4 IPsec tunnel mode performance test suite.**
- **[Top] Network Topologies:** TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- **[Enc] Packet Encapsulations:** Eth-IPv4 on TG-DUTn, Eth-IPv4-IPSec on DUT1-DUT2
- **[Cfg] DUT configuration:** DUT1 and DUT2 are configured with multiple IPsec tunnels between them. DUTs get IPv4 traffic from TG, encrypt it and send to another DUT, where packets are decrypted and sent back to TG
- **[Ver] TG verification:** In MaxReceivedRate test TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, number of flows per flow-group equals to number of IPSec tunnels) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv4 destination address) field is applied to both streams.
- **[Ref] Applicable standard specifications:** RFC4303 and RFC2544.
.. only:: html
.. csv-table::
:header-rows: 1
:widths: auto
:align: center
:file: vpp_mrr_results_40ge2p1xl710-ethip4ipsecscale1000tnl-ip4base-int-aes-gcm-mrr.csv
.. only:: latex
.. raw:: latex
\csvautolongtable{_tmp/src/detailed_test_results/vpp_mrr_results/vpp_mrr_results_40ge2p1xl710-ethip4ipsecscale1000tnl-ip4base-int-aes-gcm-mrr.csv}
40ge2p1xl710-ethip4ipsecscale1000tnl-ip4base-int-cbc-sha1-mrr
`````````````````````````````````````````````````````````````
**Raw results IPv4 IPsec tunnel mode performance test suite.**
- **[Top] Network Topologies:** TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- **[Enc] Packet Encapsulations:** Eth-IPv4 on TG-DUTn, Eth-IPv4-IPSec on DUT1-DUT2
- **[Cfg] DUT configuration:** DUT1 and DUT2 are configured with multiple IPsec tunnels between them. DUTs get IPv4 traffic from TG, encrypt it and send to another DUT, where packets are decrypted and sent back to TG
- **[Ver] TG verification:** In MaxReceivedRate test TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, number of flows per flow-group equals to number of IPSec tunnels) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv4 destination address) field is applied to both streams.
- **[Ref] Applicable standard specifications:** RFC4303 and RFC2544.
.. only:: html
.. csv-table::
:header-rows: 1
:widths: auto
:align: center
:file: vpp_mrr_results_40ge2p1xl710-ethip4ipsecscale1000tnl-ip4base-int-cbc-sha1-mrr.csv
.. only:: latex
.. raw:: latex
\csvautolongtable{_tmp/src/detailed_test_results/vpp_mrr_results/vpp_mrr_results_40ge2p1xl710-ethip4ipsecscale1000tnl-ip4base-int-cbc-sha1-mrr.csv}
ip4
---
10ge2p1x520-ethip4-ip4base-copwhtlistbase-mrr
`````````````````````````````````````````````
**Raw results IPv4 whitelist test cases**
- **[Top] Network Topologies:** TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- **[Enc] Packet Encapsulations:** Eth-IPv4 for IPv4 routing.
- **[Cfg] DUT configuration:** DUT1 and DUT2 are configured with IPv4 routing, two static IPv4 /24 routes and IPv4 COP security whitelist ingress /24 filter entries applied on links TG - DUT1 and DUT2 - TG. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.
- **[Ver] TG verification:** In MaxReceivedRate test TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- **[Ref] Applicable standard specifications:** RFC2544.
.. only:: html
.. csv-table::
:header-rows: 1
:widths: auto
:align: center
:file: vpp_mrr_results_10ge2p1x520-ethip4-ip4base-copwhtlistbase-mrr.csv
.. only:: latex
.. raw:: latex
\csvautolongtable{_tmp/src/detailed_test_results/vpp_mrr_results/vpp_mrr_results_10ge2p1x520-ethip4-ip4base-copwhtlistbase-mrr.csv}
10ge2p1x520-ethip4-ip4base-iacldstbase-mrr
``````````````````````````````````````````
**Raw results IPv4 iAcl whitelist test cases**
- **[Top] Network Topologies:** TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- **[Enc] Packet Encapsulations:** Eth-IPv4 for IPv4 routing.
- **[Cfg] DUT configuration:** DUT1 and DUT2 are configured with IPv4 routing, two static IPv4 /24 routes and IPv4 iAcl security whitelist ingress /24 filter entries applied on links TG - DUT1 and DUT2 - TG. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.
- **[Ver] TG verification:** In MaxReceivedRate tests TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv6 header and generated payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- **[Ref] Applicable standard specifications:** RFC2544.
.. only:: html
.. csv-table::
:header-rows: 1
:widths: auto
:align: center
:file: vpp_mrr_results_10ge2p1x520-ethip4-ip4base-iacldstbase-mrr.csv
.. only:: latex
.. raw:: latex
\csvautolongtable{_tmp/src/detailed_test_results/vpp_mrr_results/vpp_mrr_results_10ge2p1x520-ethip4-ip4base-iacldstbase-mrr.csv}
10ge2p1x520-ethip4-ip4base-ipolicemarkbase-mrr
``````````````````````````````````````````````
**Raw results IPv4 policer test cases**
- **[Top] Network Topologies:** TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- **[Enc] Packet Encapsulations:** Eth-IPv4 for IPv4 routing.
- **[Cfg] DUT configuration:** DUT1 and DUT2 are configured with IPv4 routing and two static IPv4 /24 route entries and policer with 2R3C color-aware configuration. Policer is applied on links TG - DUT1 and DUT2 - TG. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.
- **[Ver] TG verification:** In MaxReceivedRate tests TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv6 header and generated payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- **[Ref] Applicable standard specifications:** RFC2544, RFC2698.
.. only:: html
.. csv-table::
:header-rows: 1
:widths: auto
:align: center
:file: vpp_mrr_results_10ge2p1x520-ethip4-ip4base-ipolicemarkbase-mrr.csv
.. only:: latex
.. raw:: latex
\csvautolongtable{_tmp/src/detailed_test_results/vpp_mrr_results/vpp_mrr_results_10ge2p1x520-ethip4-ip4base-ipolicemarkbase-mrr.csv}
10ge2p1x520-ethip4-ip4base-mrr
``````````````````````````````
**Raw results IPv4 routing test cases**
- **[Top] Network Topologies:** TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- **[Enc] Packet Encapsulations:** Eth-IPv4 for IPv4 routing.
- **[Cfg] DUT configuration:** DUT1 and DUT2 are configured with IPv4 routing and two static IPv4 /24 route entries. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.
- **[Ver] TG verification:** In MaxReceivedRate test TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- **[Ref] Applicable standard specifications:** RFC2544.
.. only:: html
.. csv-table::
:header-rows: 1
:widths: auto
:align: center
:file: vpp_mrr_results_10ge2p1x520-ethip4-ip4base-mrr.csv
.. only:: latex
.. raw:: latex
\csvautolongtable{_tmp/src/detailed_test_results/vpp_mrr_results/vpp_mrr_results_10ge2p1x520-ethip4-ip4base-mrr.csv}
10ge2p1x520-ethip4-ip4scale200k-mrr
```````````````````````````````````
**Raw results IPv4 routing test cases**
- **[Top] Network Topologies:** TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- **[Enc] Packet Encapsulations:** Eth-IPv4 for IPv4 routing.
- **[Cfg] DUT configuration:** DUT1 and DUT2 are configured with IPv4 routing and 2x100k static IPv4 /32 route entries. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.
- **[Ver] TG verification:** In MaxReceivedRate test TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- **[Ref] Applicable standard specifications:** RFC2544.
.. only:: html
.. csv-table::
:header-rows: 1
:widths: auto
:align: center
:file: vpp_mrr_results_10ge2p1x520-ethip4-ip4scale200k-mrr.csv
.. only:: latex
.. raw:: latex
\csvautolongtable{_tmp/src/detailed_test_results/vpp_mrr_results/vpp_mrr_results_10ge2p1x520-ethip4-ip4scale200k-mrr.csv}
10ge2p1x520-ethip4-ip4scale20k-mrr
``````````````````````````````````
**Raw results IPv4 routing test cases**
- **[Top] Network Topologies:** TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- **[Enc] Packet Encapsulations:** Eth-IPv4 for IPv4 routing.
- **[Cfg] DUT configuration:** DUT1 and DUT2 are configured with IPv4 routing and 2x100k static IPv4 /32 route entries. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.
- **[Ver] TG verification:** In MaxReceivedRate test TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- **[Ref] Applicable standard specifications:** RFC2544.
.. only:: html
.. csv-table::
:header-rows: 1
:widths: auto
:align: center
:file: vpp_mrr_results_10ge2p1x520-ethip4-ip4scale20k-mrr.csv
.. only:: latex
.. raw:: latex
\csvautolongtable{_tmp/src/detailed_test_results/vpp_mrr_results/vpp_mrr_results_10ge2p1x520-ethip4-ip4scale20k-mrr.csv}
10ge2p1x520-ethip4-ip4scale2m-mrr
`````````````````````````````````
**Raw results IPv4 routing test cases**
- **[Top] Network Topologies:** TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- **[Enc] Packet Encapsulations:** Eth-IPv4 for IPv4 routing.
- **[Cfg] DUT configuration:** DUT1 and DUT2 are configured with IPv4 routing and 2x100k static IPv4 /32 route entries. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.
- **[Ver] TG verification:** In MaxReceivedRate test TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- **[Ref] Applicable standard specifications:** RFC2544.
.. only:: html
.. csv-table::
:header-rows: 1
:widths: auto
:align: center
:file: vpp_mrr_results_10ge2p1x520-ethip4-ip4scale2m-mrr.csv
.. only:: latex
.. raw:: latex
\csvautolongtable{_tmp/src/detailed_test_results/vpp_mrr_results/vpp_mrr_results_10ge2p1x520-ethip4-ip4scale2m-mrr.csv}
10ge2p1x520-ethip4udp-ip4base-iacl1sf-10kflows-mrr
``````````````````````````````````````````````````
**Raw results IPv4 test cases with ACL**
- **[Top] Network Topologies:** TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- **[Enc] Packet Encapsulations:** Eth-IPv4-UDP for L2 switching of IPv4.
- **[Cfg] DUT configuration:** DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with 2p10GE NIC X520 Niantic by Intel.
- **[Ver] TG verification:** In MaxReceivedRate test TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- **[Ref] Applicable standard specifications:** RFC2544.
.. only:: html
.. csv-table::
:header-rows: 1
:widths: auto
:align: center
:file: vpp_mrr_results_10ge2p1x520-ethip4udp-ip4base-iacl1sf-10kflows-mrr.csv
.. only:: latex
.. raw:: latex
\csvautolongtable{_tmp/src/detailed_test_results/vpp_mrr_results/vpp_mrr_results_10ge2p1x520-ethip4udp-ip4base-iacl1sf-10kflows-mrr.csv}
10ge2p1x520-ethip4udp-ip4base-iacl1sl-10kflows-mrr
``````````````````````````````````````````````````
**Raw results IPv4 test cases with ACL**
- **[Top] Network Topologies:** TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- **[Enc] Packet Encapsulations:** Eth-IPv4-UDP for L2 switching of IPv4.
- **[Cfg] DUT configuration:** DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with 2p10GE NIC X520 Niantic by Intel.
- **[Ver] TG verification:** In MaxReceivedRate test TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- **[Ref] Applicable standard specifications:** RFC2544.
.. only:: html
.. csv-table::
:header-rows: 1
:widths: auto
:align: center
:file: vpp_mrr_results_10ge2p1x520-ethip4udp-ip4base-iacl1sl-10kflows-mrr.csv
.. only:: latex
.. raw:: latex
\csvautolongtable{_tmp/src/detailed_test_results/vpp_mrr_results/vpp_mrr_results_10ge2p1x520-ethip4udp-ip4base-iacl1sl-10kflows-mrr.csv}
10ge2p1x520-ethip4udp-ip4base-iacl50sf-10kflows-mrr
```````````````````````````````````````````````````
**Raw results IPv4 test cases with ACL**
- **[Top] Network Topologies:** TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- **[Enc] Packet Encapsulations:** Eth-IPv4-UDP for L2 switching of IPv4.
- **[Cfg] DUT configuration:** DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with 2p10GE NIC X520 Niantic by Intel.
- **[Ver] TG verification:** In MaxReceivedRate test TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- **[Ref] Applicable standard specifications:** RFC2544.
.. only:: html
.. csv-table::
:header-rows: 1
:widths: auto
:align: center
:file: vpp_mrr_results_10ge2p1x520-ethip4udp-ip4base-iacl50sf-10kflows-mrr.csv
.. only:: latex
.. raw:: latex
\csvautolongtable{_tmp/src/detailed_test_results/vpp_mrr_results/vpp_mrr_results_10ge2p1x520-ethip4udp-ip4base-iacl50sf-10kflows-mrr.csv}
10ge2p1x520-ethip4udp-ip4base-iacl50sl-10kflows-mrr
```````````````````````````````````````````````````
**Raw results IPv4 test cases with ACL**
- **[Top] Network Topologies:** TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- **[Enc] Packet Encapsulations:** Eth-IPv4-UDP for L2 switching of IPv4.
- **[Cfg] DUT configuration:** DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with 2p10GE NIC X520 Niantic by Intel.
- **[Ver] TG verification:** In MaxReceivedRate test TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- **[Ref] Applicable standard specifications:** RFC2544.
.. only:: html
.. csv-table::
:header-rows: 1
:widths: auto
:align: center
:file: vpp_mrr_results_10ge2p1x520-ethip4udp-ip4base-iacl50sl-10kflows-mrr.csv
.. only:: latex
.. raw:: latex
\csvautolongtable{_tmp/src/detailed_test_results/vpp_mrr_results/vpp_mrr_results_10ge2p1x520-ethip4udp-ip4base-iacl50sl-10kflows-mrr.csv}
10ge2p1x520-ethip4udp-ip4base-nat44-mrr
```````````````````````````````````````
**NAT44 performance test cases**
- **[Top] Network Topologies:** TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- **[Enc] Packet Encapsulations:** Eth-IPv4-UDP for IPv4 routing.
- **[Cfg] DUT configuration:** DUT1 and DUT2 are configured with IPv4 routing and two static IPv4 /24 and IPv4/20 route entries. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.
- **[Ver] TG verification:** In MaxReceivedRate test TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- **[Ref] Applicable standard specifications:** RFC2544.
.. only:: html
.. csv-table::
:header-rows: 1
:widths: auto
:align: center
:file: vpp_mrr_results_10ge2p1x520-ethip4udp-ip4base-nat44-mrr.csv
.. only:: latex
.. raw:: latex
\csvautolongtable{_tmp/src/detailed_test_results/vpp_mrr_results/vpp_mrr_results_10ge2p1x520-ethip4udp-ip4base-nat44-mrr.csv}
10ge2p1x520-ethip4udp-ip4scale1000-udpsrcscale15-nat44-mrr
``````````````````````````````````````````````````````````
**Raw results NAT44 performance test cases**
- **[Top] Network Topologies:** TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- **[Enc] Packet Encapsulations:** Eth-IPv4-UDP for IPv4 routing.
- **[Cfg] DUT configuration:** DUT1 and DUT2 are configured with IPv4 routing and two static IPv4 /24 and IPv4/20 route entries. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.
- **[Ver] TG verification:** In MaxReceivedRate test TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- **[Ref] Applicable standard specifications:** RFC2544.
.. only:: html
.. csv-table::
:header-rows: 1
:widths: auto
:align: center
:file: vpp_mrr_results_10ge2p1x520-ethip4udp-ip4scale1000-udpsrcscale15-nat44-mrr.csv
.. only:: latex
.. raw:: latex
\csvautolongtable{_tmp/src/detailed_test_results/vpp_mrr_results/vpp_mrr_results_10ge2p1x520-ethip4udp-ip4scale1000-udpsrcscale15-nat44-mrr.csv}
10ge2p1x710-ethip4-ip4base-copwhtlistbase-mrr
`````````````````````````````````````````````
**Raw results IPv4 whitelist test cases**
- **[Top] Network Topologies:** TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- **[Enc] Packet Encapsulations:** Eth-IPv4 for IPv4 routing.
- **[Cfg] DUT configuration:** DUT1 and DUT2 are configured with IPv4 routing, two static IPv4 /24 routes and IPv4 COP security whitelist ingress /24 filter entries applied on links TG - DUT1 and DUT2 - TG. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel.
- **[Ver] TG verification:** In MaxReceivedRate test TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- **[Ref] Applicable standard specifications:** RFC2544.
.. only:: html
.. csv-table::
:header-rows: 1
:widths: auto
:align: center
:file: vpp_mrr_results_10ge2p1x710-ethip4-ip4base-copwhtlistbase-mrr.csv
.. only:: latex
.. raw:: latex
\csvautolongtable{_tmp/src/detailed_test_results/vpp_mrr_results/vpp_mrr_results_10ge2p1x710-ethip4-ip4base-copwhtlistbase-mrr.csv}
10ge2p1x710-ethip4-ip4base-iacldstbase-mrr
``````````````````````````````````````````
**Raw results IPv4 iAcl whitelist test cases**
- **[Top] Network Topologies:** TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- **[Enc] Packet Encapsulations:** Eth-IPv4 for IPv4 routing.
- **[Cfg] DUT configuration:** DUT1 and DUT2 are configured with IPv4 routing, two static IPv4 /24 routes and IPv4 iAcl security whitelist ingress /24 filter entries applied on links TG - DUT1 and DUT2 - TG. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel.
- **[Ver] TG verification:** In MaxReceivedRate tests TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv6 header and generated payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- **[Ref] Applicable standard specifications:** RFC2544.
.. only:: html
.. csv-table::
:header-rows: 1
:widths: auto
:align: center
:file: vpp_mrr_results_10ge2p1x710-ethip4-ip4base-iacldstbase-mrr.csv
.. only:: latex
.. raw:: latex
\csvautolongtable{_tmp/src/detailed_test_results/vpp_mrr_results/vpp_mrr_results_10ge2p1x710-ethip4-ip4base-iacldstbase-mrr.csv}
10ge2p1x710-ethip4-ip4base-ipolicemarkbase-mrr
``````````````````````````````````````````````
**Raw results IPv4 policer test cases**
- **[Top] Network Topologies:** TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- **[Enc] Packet Encapsulations:** Eth-IPv4 for IPv4 routing.
- **[Cfg] DUT configuration:** DUT1 and DUT2 are configured with IPv4 routing and two static IPv4 /24 route entries and policer with 2R3C color-aware configuration. Policer is applied on links TG - DUT1 and DUT2 - TG. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel.
- **[Ver] TG verification:** In MaxReceivedRate tests TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv6 header and generated payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- **[Ref] Applicable standard specifications:** RFC2544, RFC2698.
.. only:: html
.. csv-table::
:header-rows: 1
:widths: auto
:align: center
:file: vpp_mrr_results_10ge2p1x710-ethip4-ip4base-ipolicemarkbase-mrr.csv
.. only:: latex
.. raw:: latex
\csvautolongtable{_tmp/src/detailed_test_results/vpp_mrr_results/vpp_mrr_results_10ge2p1x710-ethip4-ip4base-ipolicemarkbase-mrr.csv}
10ge2p1x710-ethip4-ip4base-mrr
``````````````````````````````
**Raw results IPv4 routing test cases**
- **[Top] Network Topologies:** TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- **[Enc] Packet Encapsulations:** Eth-IPv4 for IPv4 routing.
- **[Cfg] DUT configuration:** DUT1 and DUT2 are configured with IPv4 routing and two static IPv4 /24 route entries. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel.
- **[Ver] TG verification:** In MaxReceivedRate test TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- **[Ref] Applicable standard specifications:** RFC2544.
.. only:: html
.. csv-table::
:header-rows: 1
:widths: auto
:align: center
:file: vpp_mrr_results_10ge2p1x710-ethip4-ip4base-mrr.csv
.. only:: latex
.. raw:: latex
\csvautolongtable{_tmp/src/detailed_test_results/vpp_mrr_results/vpp_mrr_results_10ge2p1x710-ethip4-ip4base-mrr.csv}
10ge2p1x710-ethip4-ip4scale200k-mrr
```````````````````````````````````
**Raw results IPv4 routing test cases**
- **[Top] Network Topologies:** TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- **[Enc] Packet Encapsulations:** Eth-IPv4 for IPv4 routing.
- **[Cfg] DUT configuration:** DUT1 and DUT2 are configured with IPv4 routing and 2x100k static IPv4 /32 route entries. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel.
- **[Ver] TG verification:** In MaxReceivedRate test TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- **[Ref] Applicable standard specifications:** RFC2544.
.. only:: html
.. csv-table::
:header-rows: 1
:widths: auto
:align: center
:file: vpp_mrr_results_10ge2p1x710-ethip4-ip4scale200k-mrr.csv
.. only:: latex
.. raw:: latex
\csvautolongtable{_tmp/src/detailed_test_results/vpp_mrr_results/vpp_mrr_results_10ge2p1x710-ethip4-ip4scale200k-mrr.csv}
10ge2p1x710-ethip4-ip4scale20k-mrr
``````````````````````````````````
**Raw results IPv4 routing test cases**
- **[Top] Network Topologies:** TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- **[Enc] Packet Encapsulations:** Eth-IPv4 for IPv4 routing.
- **[Cfg] DUT configuration:** DUT1 and DUT2 are configured with IPv4 routing and 2x100k static IPv4 /32 route entries. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel.
- **[Ver] TG verification:** In MaxReceivedRate test TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- **[Ref] Applicable standard specifications:** RFC2544.
.. only:: html
.. csv-table::
:header-rows: 1
:widths: auto
:align: center
:file: vpp_mrr_results_10ge2p1x710-ethip4-ip4scale20k-mrr.csv
.. only:: latex
.. raw:: latex
\csvautolongtable{_tmp/src/detailed_test_results/vpp_mrr_results/vpp_mrr_results_10ge2p1x710-ethip4-ip4scale20k-mrr.csv}
10ge2p1x710-ethip4-ip4scale2m-mrr
`````````````````````````````````
**Raw results IPv4 routing test cases**
- **[Top] Network Topologies:** TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- **[Enc] Packet Encapsulations:** Eth-IPv4 for IPv4 routing.
- **[Cfg] DUT configuration:** DUT1 and DUT2 are configured with IPv4 routing and 2x100k static IPv4 /32 route entries. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel.
- **[Ver] TG verification:** In MaxReceivedRate test TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- **[Ref] Applicable standard specifications:** RFC2544.
.. only:: html
.. csv-table::
:header-rows: 1
:widths: auto
:align: center
:file: vpp_mrr_results_10ge2p1x710-ethip4-ip4scale2m-mrr.csv
.. only:: latex
.. raw:: latex
\csvautolongtable{_tmp/src/detailed_test_results/vpp_mrr_results/vpp_mrr_results_10ge2p1x710-ethip4-ip4scale2m-mrr.csv}
10ge2p1x710-ethip4udp-ip4base-iacl1sf-10kflows-mrr
``````````````````````````````````````````````````
**Raw results IPv4 test cases with ACL**
- **[Top] Network Topologies:** TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- **[Enc] Packet Encapsulations:** Eth-IPv4-UDP for L2 switching of IPv4.
- **[Cfg] DUT configuration:** DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with 2p10GE NIC X710 by Intel.
- **[Ver] TG verification:** In MaxReceivedRate test TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- **[Ref] Applicable standard specifications:** RFC2544.
.. only:: html
.. csv-table::
:header-rows: 1
:widths: auto
:align: center
:file: vpp_mrr_results_10ge2p1x710-ethip4udp-ip4base-iacl1sf-10kflows-mrr.csv
.. only:: latex
.. raw:: latex
\csvautolongtable{_tmp/src/detailed_test_results/vpp_mrr_results/vpp_mrr_results_10ge2p1x710-ethip4udp-ip4base-iacl1sf-10kflows-mrr.csv}
10ge2p1x710-ethip4udp-ip4base-iacl1sl-10kflows-mrr
``````````````````````````````````````````````````
**Raw results IPv4 test cases with ACL**
- **[Top] Network Topologies:** TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- **[Enc] Packet Encapsulations:** Eth-IPv4-UDP for L2 switching of IPv4.
- **[Cfg] DUT configuration:** DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with 2p10GE NIC X710 by Intel.
- **[Ver] TG verification:** In MaxReceivedRate test TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- **[Ref] Applicable standard specifications:** RFC2544.
.. only:: html
.. csv-table::
:header-rows: 1
:widths: auto
:align: center
:file: vpp_mrr_results_10ge2p1x710-ethip4udp-ip4base-iacl1sl-10kflows-mrr.csv
.. only:: latex
.. raw:: latex
\csvautolongtable{_tmp/src/detailed_test_results/vpp_mrr_results/vpp_mrr_results_10ge2p1x710-ethip4udp-ip4base-iacl1sl-10kflows-mrr.csv}
10ge2p1x710-ethip4udp-ip4base-iacl50sf-10kflows-mrr
```````````````````````````````````````````````````
**Raw results IPv4 test cases with ACL**
- **[Top] Network Topologies:** TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- **[Enc] Packet Encapsulations:** Eth-IPv4-UDP for L2 switching of IPv4.
- **[Cfg] DUT configuration:** DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with 2p10GE NIC X710 by Intel.
- **[Ver] TG verification:** In MaxReceivedRate test TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- **[Ref] Applicable standard specifications:** RFC2544.
.. only:: html
.. csv-table::
:header-rows: 1
:widths: auto
:align: center
:file: vpp_mrr_results_10ge2p1x710-ethip4udp-ip4base-iacl50sf-10kflows-mrr.csv
.. only:: latex
.. raw:: latex
\csvautolongtable{_tmp/src/detailed_test_results/vpp_mrr_results/vpp_mrr_results_10ge2p1x710-ethip4udp-ip4base-iacl50sf-10kflows-mrr.csv}
10ge2p1x710-ethip4udp-ip4base-iacl50sl-10kflows-mrr
```````````````````````````````````````````````````
**Raw results IPv4 test cases with ACL**
- **[Top] Network Topologies:** TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- **[Enc] Packet Encapsulations:** Eth-IPv4-UDP for L2 switching of IPv4.
- **[Cfg] DUT configuration:** DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with 2p10GE NIC X710 by Intel.
- **[Ver] TG verification:** In MaxReceivedRate test TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- **[Ref] Applicable standard specifications:** RFC2544.
.. only:: html
.. csv-table::
:header-rows: 1
:widths: auto
:align: center
:file: vpp_mrr_results_10ge2p1x710-ethip4udp-ip4base-iacl50sl-10kflows-mrr.csv
.. only:: latex
.. raw:: latex
\csvautolongtable{_tmp/src/detailed_test_results/vpp_mrr_results/vpp_mrr_results_10ge2p1x710-ethip4udp-ip4base-iacl50sl-10kflows-mrr.csv}
10ge2p1x710-ethip4udp-ip4base-nat44-mrr
```````````````````````````````````````
**NAT44 performance test cases**
- **[Top] Network Topologies:** TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- **[Enc] Packet Encapsulations:** Eth-IPv4-UDP for IPv4 routing.
- **[Cfg] DUT configuration:** DUT1 and DUT2 are configured with IPv4 routing and two static IPv4 /24 and IPv4/20 route entries. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel.
- **[Ver] TG verification:** In MaxReceivedRate test TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- **[Ref] Applicable standard specifications:** RFC2544.
.. only:: html
.. csv-table::
:header-rows: 1
:widths: auto
:align: center
:file: vpp_mrr_results_10ge2p1x710-ethip4udp-ip4base-nat44-mrr.csv
.. only:: latex
.. raw:: latex
\csvautolongtable{_tmp/src/detailed_test_results/vpp_mrr_results/vpp_mrr_results_10ge2p1x710-ethip4udp-ip4base-nat44-mrr.csv}
10ge2p1x710-ethip4udp-ip4scale1000-udpsrcscale15-nat44-mrr
``````````````````````````````````````````````````````````
**Raw results NAT44 performance test cases**
- **[Top] Network Topologies:** TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- **[Enc] Packet Encapsulations:** Eth-IPv4-UDP for IPv4 routing.
- **[Cfg] DUT configuration:** DUT1 and DUT2 are configured with IPv4 routing and two static IPv4 /24 and IPv4/20 route entries. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel.
- **[Ver] TG verification:** In MaxReceivedRate test TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- **[Ref] Applicable standard specifications:** RFC2544.
.. only:: html
.. csv-table::
:header-rows: 1
:widths: auto
:align: center
:file: vpp_mrr_results_10ge2p1x710-ethip4udp-ip4scale1000-udpsrcscale15-nat44-mrr.csv
.. only:: latex
.. raw:: latex
\csvautolongtable{_tmp/src/detailed_test_results/vpp_mrr_results/vpp_mrr_results_10ge2p1x710-ethip4udp-ip4scale1000-udpsrcscale15-nat44-mrr.csv}
40ge2p1xl710-ethip4-ip4base-mrr
```````````````````````````````
**Raw results IPv4 routing test cases**
- **[Top] Network Topologies:** TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- **[Enc] Packet Encapsulations:** Eth-IPv4 for IPv4 routing.
- **[Cfg] DUT configuration:** DUT1 and DUT2 are configured with IPv4 routing and two static IPv4 /24 route entries. DUT1 and DUT2 tested with 2p10GE NIC XL710 by Intel.
- **[Ver] TG verification:** In MaxReceivedRate test TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- **[Ref] Applicable standard specifications:** RFC2544.
.. only:: html
.. csv-table::
:header-rows: 1
:widths: auto
:align: center
:file: vpp_mrr_results_40ge2p1xl710-ethip4-ip4base-mrr.csv
.. only:: latex
.. raw:: latex
\csvautolongtable{_tmp/src/detailed_test_results/vpp_mrr_results/vpp_mrr_results_40ge2p1xl710-ethip4-ip4base-mrr.csv}
ip4 tunnels
-----------
10ge2p1x520-ethip4lispip4-ip4base-mrr
`````````````````````````````````````
**Raw results Lisp test cases**
- **[Top] Network Topologies:** TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- **[Enc] Packet Encapsulations:** Eth-IPv4-LISP-IPv4 on DUT1-DUT2, Eth-IPv4 on TG-DUTn for IPv4 routing over LISPoIPv4 tunnel.
- **[Cfg] DUT configuration:** DUT1 and DUT2 are configured with IPv4 routing and static routes. LISPoIPv4 tunnel is configured between DUT1 and DUT2. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.
- **[Ver] TG verification:** In MaxReceivedRate test TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- **[Ref] Applicable standard specifications:** RFC6830.
.. only:: html
.. csv-table::
:header-rows: 1
:widths: auto
:align: center
:file: vpp_mrr_results_10ge2p1x520-ethip4lispip4-ip4base-mrr.csv
.. only:: latex
.. raw:: latex
\csvautolongtable{_tmp/src/detailed_test_results/vpp_mrr_results/vpp_mrr_results_10ge2p1x520-ethip4lispip4-ip4base-mrr.csv}
10ge2p1x520-ethip4vxlan-l2bdbasemaclrn-mrr
``````````````````````````````````````````
**Raw results L2BD with VXLANoIPv4 test cases**
- **[Top] Network Topologies:** TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- **[Enc] Packet Encapsulations:** Eth-IPv4 for L2 bridge domain on TG-DUTn. Eth-IPv4-VXLAN-Eth-IPv4 is applied on link between DUT1 and DUT2.
- **[Cfg] DUT configuration:** DUT1 and DUT2 are configured with L2 bridge domain. VXLAN tunnels are configured between L2BDs on DUT1 and DUT2. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.
- **[Ver] TG verification:** In MaxReceivedRate test TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- **[Ref] Applicable standard specifications:** RFC2544, RFC7348.
.. only:: html
.. csv-table::
:header-rows: 1
:widths: auto
:align: center
:file: vpp_mrr_results_10ge2p1x520-ethip4vxlan-l2bdbasemaclrn-mrr.csv
.. only:: latex
.. raw:: latex
\csvautolongtable{_tmp/src/detailed_test_results/vpp_mrr_results/vpp_mrr_results_10ge2p1x520-ethip4vxlan-l2bdbasemaclrn-mrr.csv}
10ge2p1x520-ethip4vxlan-l2xcbase-mrr
````````````````````````````````````
**Raw results L2XC with VXLANoIPv4 test cases**
- **[Top] Network Topologies:** TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- **[Enc] Packet Encapsulations:** Eth-IPv4 for L2 cross-connect on TG-DUTn. Eth-IPv4-VXLAN-Eth-IPv4 is applied on link between DUT1 and DUT2.
- **[Cfg] DUT configuration:** DUT1 and DUT2 are configured with L2 cross- connect. VXLAN tunnels are configured between L2XCs on DUT1 and DUT2. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.
- **[Ver] TG verification:** In MaxReceivedRate test TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- **[Ref] Applicable standard specifications:** RFC2544, RFC7348.
.. only:: html
.. csv-table::
:header-rows: 1
:widths: auto
:align: center
:file: vpp_mrr_results_10ge2p1x520-ethip4vxlan-l2xcbase-mrr.csv
.. only:: latex
.. raw:: latex
\csvautolongtable{_tmp/src/detailed_test_results/vpp_mrr_results/vpp_mrr_results_10ge2p1x520-ethip4vxlan-l2xcbase-mrr.csv}
10ge2p1x710-ethip4lispip4-ip4base-mrr
`````````````````````````````````````
**Raw results Lisp test cases**
- **[Top] Network Topologies:** TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- **[Enc] Packet Encapsulations:** Eth-IPv4-LISP-IPv4 on DUT1-DUT2, Eth-IPv4 on TG-DUTn for IPv4 routing over LISPoIPv4 tunnel.
- **[Cfg] DUT configuration:** DUT1 and DUT2 are configured with IPv4 routing and static routes. LISPoIPv4 tunnel is configured between DUT1 and DUT2. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel.
- **[Ver] TG verification:** In MaxReceivedRate test TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- **[Ref] Applicable standard specifications:** RFC6830.
.. only:: html
.. csv-table::
:header-rows: 1
:widths: auto
:align: center
:file: vpp_mrr_results_10ge2p1x710-ethip4lispip4-ip4base-mrr.csv
.. only:: latex
.. raw:: latex
\csvautolongtable{_tmp/src/detailed_test_results/vpp_mrr_results/vpp_mrr_results_10ge2p1x710-ethip4lispip4-ip4base-mrr.csv}
10ge2p1x710-ethip4vxlan-l2bdbasemaclrn-mrr
``````````````````````````````````````````
**Raw results L2BD with VXLANoIPv4 test cases**
- **[Top] Network Topologies:** TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- **[Enc] Packet Encapsulations:** Eth-IPv4 for L2 bridge domain on TG-DUTn. Eth-IPv4-VXLAN-Eth-IPv4 is applied on link between DUT1 and DUT2.
- **[Cfg] DUT configuration:** DUT1 and DUT2 are configured with L2 bridge domain. VXLAN tunnels are configured between L2BDs on DUT1 and DUT2. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel.
- **[Ver] TG verification:** In MaxReceivedRate test TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- **[Ref] Applicable standard specifications:** RFC2544, RFC7348.
.. only:: html
.. csv-table::
:header-rows: 1
:widths: auto
:align: center
:file: vpp_mrr_results_10ge2p1x710-ethip4vxlan-l2bdbasemaclrn-mrr.csv
.. only:: latex
.. raw:: latex
\csvautolongtable{_tmp/src/detailed_test_results/vpp_mrr_results/vpp_mrr_results_10ge2p1x710-ethip4vxlan-l2bdbasemaclrn-mrr.csv}
10ge2p1x710-ethip4vxlan-l2xcbase-mrr
````````````````````````````````````
**Raw results L2XC with VXLANoIPv4 test cases**
- **[Top] Network Topologies:** TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- **[Enc] Packet Encapsulations:** Eth-IPv4 for L2 cross-connect on TG-DUTn. Eth-IPv4-VXLAN-Eth-IPv4 is applied on link between DUT1 and DUT2.
- **[Cfg] DUT configuration:** DUT1 and DUT2 are configured with L2 cross- connect. VXLAN tunnels are configured between L2XCs on DUT1 and DUT2. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel.
- **[Ver] TG verification:** In MaxReceivedRate test TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- **[Ref] Applicable standard specifications:** RFC2544, RFC7348.
.. only:: html
.. csv-table::
:header-rows: 1
:widths: auto
:align: center
:file: vpp_mrr_results_10ge2p1x710-ethip4vxlan-l2xcbase-mrr.csv
.. only:: latex
.. raw:: latex
\csvautolongtable{_tmp/src/detailed_test_results/vpp_mrr_results/vpp_mrr_results_10ge2p1x710-ethip4vxlan-l2xcbase-mrr.csv}
ip6
---
10ge2p1x520-ethip6-ip6base-copwhtlistbase-mrr
`````````````````````````````````````````````
**Raw results IPv6 whitelist test cases**
- **[Top] Network Topologies:** TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- **[Enc] Packet Encapsulations:** Eth-IPv6 for IPv6 routing.
- **[Cfg] DUT configuration:** DUT1 and DUT2 are configured with IPv6 routing, two static IPv6 /64 routes and IPv6 COP security whitelist ingress /64 filter entries applied on links TG - DUT1 and DUT2 - TG. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.
- **[Ver] TG verification:** In MaxReceivedRate tests TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv6 header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- **[Ref] Applicable standard specifications:** RFC2544.
.. only:: html
.. csv-table::
:header-rows: 1
:widths: auto
:align: center
:file: vpp_mrr_results_10ge2p1x520-ethip6-ip6base-copwhtlistbase-mrr.csv
.. only:: latex
.. raw:: latex
\csvautolongtable{_tmp/src/detailed_test_results/vpp_mrr_results/vpp_mrr_results_10ge2p1x520-ethip6-ip6base-copwhtlistbase-mrr.csv}
10ge2p1x520-ethip6-ip6base-iacldstbase-mrr
``````````````````````````````````````````
**Raw results IPv6 iAcl whitelist test cases**
- **[Top] Network Topologies:** TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- **[Enc] Packet Encapsulations:** Eth-IPv6 for IPv6 routing.
- **[Cfg] DUT configuration:** DUT1 and DUT2 are configured with IPv6 routing, two static IPv6 /64 routes and IPv6 iAcl security whitelist ingress /64 filter entries applied on links TG - DUT1 and DUT2 - TG. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.
- **[Ver] TG verification:** In MaxReceivedRate tests TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv6 header and generated payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- **[Ref] Applicable standard specifications:** RFC2544.
.. only:: html
.. csv-table::
:header-rows: 1
:widths: auto
:align: center
:file: vpp_mrr_results_10ge2p1x520-ethip6-ip6base-iacldstbase-mrr.csv
.. only:: latex
.. raw:: latex
\csvautolongtable{_tmp/src/detailed_test_results/vpp_mrr_results/vpp_mrr_results_10ge2p1x520-ethip6-ip6base-iacldstbase-mrr.csv}
10ge2p1x520-ethip6-ip6base-mrr
``````````````````````````````
**Raw results IPv6 routing test cases**
- **[Top] Network Topologies:** TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- **[Enc] Packet Encapsulations:** Eth-IPv6 for IPv6 routing.
- **[Cfg] DUT configuration:** DUT1 and DUT2 are configured with IPv6 routing and two static IPv6 /64 route entries. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.
- **[Ver] TG verification:** In MaxReceivedRate test TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv6 header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- **[Ref] Applicable standard specifications:** RFC2544.
.. only:: html
.. csv-table::
:header-rows: 1
:widths: auto
:align: center
:file: vpp_mrr_results_10ge2p1x520-ethip6-ip6base-mrr.csv
.. only:: latex
.. raw:: latex
\csvautolongtable{_tmp/src/detailed_test_results/vpp_mrr_results/vpp_mrr_results_10ge2p1x520-ethip6-ip6base-mrr.csv}
10ge2p1x520-ethip6-ip6scale200k-mrr
```````````````````````````````````
**Raw results IPv6 routing test cases**
- **[Top] Network Topologies:** TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- **[Enc] Packet Encapsulations:** Eth-IPv6 for IPv6 routing.
- **[Cfg] DUT configuration:** DUT1 and DUT2 are configured with IPv6 routing and 2x100k static IPv6 /64 route entries. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.
- **[Ver] TG verification:** In MaxReceivedRate tests TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100k flows per flow-group) with all packets containing Ethernet header, IPv6 header withq IP and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv6 destination address) field is applied to both streams.
- **[Ref] Applicable standard specifications:** RFC2544.
.. only:: html
.. csv-table::
:header-rows: 1
:widths: auto
:align: center
:file: vpp_mrr_results_10ge2p1x520-ethip6-ip6scale200k-mrr.csv
.. only:: latex
.. raw:: latex
\csvautolongtable{_tmp/src/detailed_test_results/vpp_mrr_results/vpp_mrr_results_10ge2p1x520-ethip6-ip6scale200k-mrr.csv}
10ge2p1x520-ethip6-ip6scale20k-mrr
``````````````````````````````````
**Raw results IPv6 routing test cases**
- **[Top] Network Topologies:** TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- **[Enc] Packet Encapsulations:** Eth-IPv6 for IPv6 routing.
- **[Cfg] DUT configuration:** DUT1 and DUT2 are configured with IPv6 routing and 2x10k static IPv6 /64 route entries. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.
- **[Ver] TG verification:** In MaxReceivedRate tests TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv6 header withq IP and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv6 destination address) field is applied to both streams.
- **[Ref] Applicable standard specifications:** RFC2544.
.. only:: html
.. csv-table::
:header-rows: 1
:widths: auto
:align: center
:file: vpp_mrr_results_10ge2p1x520-ethip6-ip6scale20k-mrr.csv
.. only:: latex
.. raw:: latex
\csvautolongtable{_tmp/src/detailed_test_results/vpp_mrr_results/vpp_mrr_results_10ge2p1x520-ethip6-ip6scale20k-mrr.csv}
10ge2p1x520-ethip6-ip6scale2m-mrr
`````````````````````````````````
**Raw results IPv6 routing test cases**
- **[Top] Network Topologies:** TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- **[Enc] Packet Encapsulations:** Eth-IPv6 for IPv6 routing.
- **[Cfg] DUT configuration:** DUT1 and DUT2 are configured with IPv6 routing and 2x1M static IPv6 /64 route entries. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.
- **[Ver] TG verification:** In MaxReceivedRate tests TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 1M flows per flow-group) with all packets containing Ethernet header, IPv6 header withq IP and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv6 destination address) field is applied to both streams.
- **[Ref] Applicable standard specifications:** RFC2544.
.. only:: html
.. csv-table::
:header-rows: 1
:widths: auto
:align: center
:file: vpp_mrr_results_10ge2p1x520-ethip6-ip6scale2m-mrr.csv
.. only:: latex
.. raw:: latex
\csvautolongtable{_tmp/src/detailed_test_results/vpp_mrr_results/vpp_mrr_results_10ge2p1x520-ethip6-ip6scale2m-mrr.csv}
10ge2p1x710-ethip6-ip6base-copwhtlistbase-mrr
`````````````````````````````````````````````
**Raw results IPv6 whitelist test cases**
- **[Top] Network Topologies:** TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- **[Enc] Packet Encapsulations:** Eth-IPv6 for IPv6 routing.
- **[Cfg] DUT configuration:** DUT1 and DUT2 are configured with IPv6 routing, two static IPv6 /64 routes and IPv6 COP security whitelist ingress /64 filter entries applied on links TG - DUT1 and DUT2 - TG. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel.
- **[Ver] TG verification:** In MaxReceivedRate tests TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv6 header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- **[Ref] Applicable standard specifications:** RFC2544.
.. only:: html
.. csv-table::
:header-rows: 1
:widths: auto
:align: center
:file: vpp_mrr_results_10ge2p1x710-ethip6-ip6base-copwhtlistbase-mrr.csv
.. only:: latex
.. raw:: latex
\csvautolongtable{_tmp/src/detailed_test_results/vpp_mrr_results/vpp_mrr_results_10ge2p1x710-ethip6-ip6base-copwhtlistbase-mrr.csv}
10ge2p1x710-ethip6-ip6base-iacldstbase-mrr
``````````````````````````````````````````
**Raw results IPv6 iAcl whitelist test cases**
- **[Top] Network Topologies:** TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- **[Enc] Packet Encapsulations:** Eth-IPv6 for IPv6 routing.
- **[Cfg] DUT configuration:** DUT1 and DUT2 are configured with IPv6 routing, two static IPv6 /64 routes and IPv6 iAcl security whitelist ingress /64 filter entries applied on links TG - DUT1 and DUT2 - TG. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel.
- **[Ver] TG verification:** In MaxReceivedRate tests TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv6 header and generated payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- **[Ref] Applicable standard specifications:** RFC2544.
.. only:: html
.. csv-table::
:header-rows: 1
:widths: auto
:align: center
:file: vpp_mrr_results_10ge2p1x710-ethip6-ip6base-iacldstbase-mrr.csv
.. only:: latex
.. raw:: latex
\csvautolongtable{_tmp/src/detailed_test_results/vpp_mrr_results/vpp_mrr_results_10ge2p1x710-ethip6-ip6base-iacldstbase-mrr.csv}
10ge2p1x710-ethip6-ip6base-mrr
``````````````````````````````
**Raw results IPv6 routing test cases**
- **[Top] Network Topologies:** TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- **[Enc] Packet Encapsulations:** Eth-IPv6 for IPv6 routing.
- **[Cfg] DUT configuration:** DUT1 and DUT2 are configured with IPv6 routing and two static IPv6 /64 route entries. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel.
- **[Ver] TG verification:** In MaxReceivedRate test TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv6 header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- **[Ref] Applicable standard specifications:** RFC2544.
.. only:: html
.. csv-table::
:header-rows: 1
:widths: auto
:align: center
:file: vpp_mrr_results_10ge2p1x710-ethip6-ip6base-mrr.csv
.. only:: latex
.. raw:: latex
\csvautolongtable{_tmp/src/detailed_test_results/vpp_mrr_results/vpp_mrr_results_10ge2p1x710-ethip6-ip6base-mrr.csv}
10ge2p1x710-ethip6-ip6scale200k-mrr
```````````````````````````````````
**Raw results IPv6 routing test cases**
- **[Top] Network Topologies:** TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- **[Enc] Packet Encapsulations:** Eth-IPv6 for IPv6 routing.
- **[Cfg] DUT configuration:** DUT1 and DUT2 are configured with IPv6 routing and 2x100k static IPv6 /64 route entries. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel.
- **[Ver] TG verification:** In MaxReceivedRate tests TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100k flows per flow-group) with all packets containing Ethernet header, IPv6 header withq IP and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv6 destination address) field is applied to both streams.
- **[Ref] Applicable standard specifications:** RFC2544.
.. only:: html
.. csv-table::
:header-rows: 1
:widths: auto
:align: center
:file: vpp_mrr_results_10ge2p1x710-ethip6-ip6scale200k-mrr.csv
.. only:: latex
.. raw:: latex
\csvautolongtable{_tmp/src/detailed_test_results/vpp_mrr_results/vpp_mrr_results_10ge2p1x710-ethip6-ip6scale200k-mrr.csv}
10ge2p1x710-ethip6-ip6scale20k-mrr
``````````````````````````````````
**Raw results IPv6 routing test cases**
- **[Top] Network Topologies:** TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- **[Enc] Packet Encapsulations:** Eth-IPv6 for IPv6 routing.
- **[Cfg] DUT configuration:** DUT1 and DUT2 are configured with IPv6 routing and 2x10k static IPv6 /64 route entries. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel.
- **[Ver] TG verification:** In MaxReceivedRate tests TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv6 header withq IP and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv6 destination address) field is applied to both streams.
- **[Ref] Applicable standard specifications:** RFC2544.
.. only:: html
.. csv-table::
:header-rows: 1
:widths: auto
:align: center
:file: vpp_mrr_results_10ge2p1x710-ethip6-ip6scale20k-mrr.csv
.. only:: latex
.. raw:: latex
\csvautolongtable{_tmp/src/detailed_test_results/vpp_mrr_results/vpp_mrr_results_10ge2p1x710-ethip6-ip6scale20k-mrr.csv}
10ge2p1x710-ethip6-ip6scale2m-mrr
`````````````````````````````````
**Raw results IPv6 routing test cases**
- **[Top] Network Topologies:** TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- **[Enc] Packet Encapsulations:** Eth-IPv6 for IPv6 routing.
- **[Cfg] DUT configuration:** DUT1 and DUT2 are configured with IPv6 routing and 2x1M static IPv6 /64 route entries. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel.
- **[Ver] TG verification:** In MaxReceivedRate tests TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 1M flows per flow-group) with all packets containing Ethernet header, IPv6 header withq IP and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv6 destination address) field is applied to both streams.
- **[Ref] Applicable standard specifications:** RFC2544.
.. only:: html
.. csv-table::
:header-rows: 1
:widths: auto
:align: center
:file: vpp_mrr_results_10ge2p1x710-ethip6-ip6scale2m-mrr.csv
.. only:: latex
.. raw:: latex
\csvautolongtable{_tmp/src/detailed_test_results/vpp_mrr_results/vpp_mrr_results_10ge2p1x710-ethip6-ip6scale2m-mrr.csv}
40ge2p1xl710-ethip6-ip6base-mrr
```````````````````````````````
**Raw results IPv6 routing test cases**
- **[Top] Network Topologies:** TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- **[Enc] Packet Encapsulations:** Eth-IPv6 for IPv6 routing.
- **[Cfg] DUT configuration:** DUT1 and DUT2 are configured with IPv6 routing and two static IPv6 /64 route entries. DUT1 and DUT2 tested with 2p40GE NIC XL710 by Intel.
- **[Ver] TG verification:** In MaxReceivedRate test TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv6 header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- **[Ref] Applicable standard specifications:** RFC2544.
.. only:: html
.. csv-table::
:header-rows: 1
:widths: auto
:align: center
:file: vpp_mrr_results_40ge2p1xl710-ethip6-ip6base-mrr.csv
.. only:: latex
.. raw:: latex
\csvautolongtable{_tmp/src/detailed_test_results/vpp_mrr_results/vpp_mrr_results_40ge2p1xl710-ethip6-ip6base-mrr.csv}
l2
--
10ge2p1x520-dot1q-l2bdbasemaclrn-mrr
````````````````````````````````````
**Raw results L2BD test cases with 802.1q test cases**
- **[Top] Network Topologies:** TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- **[Enc] Packet Encapsulations:** Eth-IPv4 for L2 switching of IPv4. 802.1q tagging is applied on link between DUT1 and DUT2.
- **[Cfg] DUT configuration:** DUT1 and DUT2 are configured with L2 bridge domain and MAC learning enabled. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.
- **[Ver] TG verification:** In MaxReceivedRate tests TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 254 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- **[Ref] Applicable standard specifications:** RFC2544.
.. only:: html
.. csv-table::
:header-rows: 1
:widths: auto
:align: center
:file: vpp_mrr_results_10ge2p1x520-dot1q-l2bdbasemaclrn-mrr.csv
.. only:: latex
.. raw:: latex
\csvautolongtable{_tmp/src/detailed_test_results/vpp_mrr_results/vpp_mrr_results_10ge2p1x520-dot1q-l2bdbasemaclrn-mrr.csv}
10ge2p1x520-dot1q-l2xcbase-mrr
``````````````````````````````
**Raw results L2XC with 802.1q test cases**
- **[Top] Network Topologies:** TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- **[Enc] Packet Encapsulations:** Eth-IPv4 for L2 cross connect. 802.1q tagging is applied on link between DUT1 and DUT2.
- **[Cfg] DUT configuration:** DUT1 and DUT2 are configured with L2 cross- connect. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.
- **[Ver] TG verification:** In MaxReceivedRate tests TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- **[Ref] Applicable standard specifications:** RFC2544.
.. only:: html
.. csv-table::
:header-rows: 1
:widths: auto
:align: center
:file: vpp_mrr_results_10ge2p1x520-dot1q-l2xcbase-mrr.csv
.. only:: latex
.. raw:: latex
\csvautolongtable{_tmp/src/detailed_test_results/vpp_mrr_results/vpp_mrr_results_10ge2p1x520-dot1q-l2xcbase-mrr.csv}
10ge2p1x520-eth-l2bdbasemaclrn-iacl1sf-10kflows-mrr
```````````````````````````````````````````````````
**Raw results L2BD test cases with ACL**
- **[Top] Network Topologies:** TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- **[Enc] Packet Encapsulations:** Eth-IPv4-UDP for L2 switching of IPv4.
- **[Cfg] DUT configuration:** DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with 2p10GE NIC X520 Niantic by Intel.
- **[Ver] TG verification:** In MaxReceivedRate tests TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- **[Ref] Applicable standard specifications:** RFC2544.
.. only:: html
.. csv-table::
:header-rows: 1
:widths: auto
:align: center
:file: vpp_mrr_results_10ge2p1x520-eth-l2bdbasemaclrn-iacl1sf-10kflows-mrr.csv
.. only:: latex
.. raw:: latex
\csvautolongtable{_tmp/src/detailed_test_results/vpp_mrr_results/vpp_mrr_results_10ge2p1x520-eth-l2bdbasemaclrn-iacl1sf-10kflows-mrr.csv}
10ge2p1x520-eth-l2bdbasemaclrn-iacl1sl-10kflows-mrr
```````````````````````````````````````````````````
**Raw results L2BD test cases with ACL**
- **[Top] Network Topologies:** TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- **[Enc] Packet Encapsulations:** Eth-IPv4-UDP for L2 switching of IPv4.
- **[Cfg] DUT configuration:** DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with 2p10GE NIC X520 Niantic by Intel.
- **[Ver] TG verification:** In MaxReceivedRate tests TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- **[Ref] Applicable standard specifications:** RFC2544.
.. only:: html
.. csv-table::
:header-rows: 1
:widths: auto
:align: center
:file: vpp_mrr_results_10ge2p1x520-eth-l2bdbasemaclrn-iacl1sl-10kflows-mrr.csv
.. only:: latex
.. raw:: latex
\csvautolongtable{_tmp/src/detailed_test_results/vpp_mrr_results/vpp_mrr_results_10ge2p1x520-eth-l2bdbasemaclrn-iacl1sl-10kflows-mrr.csv}
10ge2p1x520-eth-l2bdbasemaclrn-iacl50sf-10kflows-mrr
````````````````````````````````````````````````````
**Raw results L2BD test cases with ACL**
- **[Top] Network Topologies:** TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- **[Enc] Packet Encapsulations:** Eth-IPv4-UDP for L2 switching of IPv4.
- **[Cfg] DUT configuration:** DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with 2p10GE NIC X520 Niantic by Intel.
- **[Ver] TG verification:** In MaxReceivedRate tests TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- **[Ref] Applicable standard specifications:** RFC2544.
.. only:: html
.. csv-table::
:header-rows: 1
:widths: auto
:align: center
:file: vpp_mrr_results_10ge2p1x520-eth-l2bdbasemaclrn-iacl50sf-10kflows-mrr.csv
.. only:: latex
.. raw:: latex
\csvautolongtable{_tmp/src/detailed_test_results/vpp_mrr_results/vpp_mrr_results_10ge2p1x520-eth-l2bdbasemaclrn-iacl50sf-10kflows-mrr.csv}
10ge2p1x520-eth-l2bdbasemaclrn-iacl50sl-10kflows-mrr
````````````````````````````````````````````````````
**Raw results L2BD test cases with ACL**
- **[Top] Network Topologies:** TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- **[Enc] Packet Encapsulations:** Eth-IPv4-UDP for L2 switching of IPv4.
- **[Cfg] DUT configuration:** DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with 2p10GE NIC X520 Niantic by Intel.
- **[Ver] TG verification:** In MaxReceivedRate tests TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- **[Ref] Applicable standard specifications:** RFC2544.
.. only:: html
.. csv-table::
:header-rows: 1
:widths: auto
:align: center
:file: vpp_mrr_results_10ge2p1x520-eth-l2bdbasemaclrn-iacl50sl-10kflows-mrr.csv
.. only:: latex
.. raw:: latex
\csvautolongtable{_tmp/src/detailed_test_results/vpp_mrr_results/vpp_mrr_results_10ge2p1x520-eth-l2bdbasemaclrn-iacl50sl-10kflows-mrr.csv}
10ge2p1x520-eth-l2bdbasemaclrn-mrr
``````````````````````````````````
**Raw results L2BD test cases**
- **[Top] Network Topologies:** TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- **[Enc] Packet Encapsulations:** Eth-IPv4 for L2 switching of IPv4.
- **[Cfg] DUT configuration:** DUT1 and DUT2 are configured with L2 bridge- domain and MAC learning enabled. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.
- **[Ver] TG verification:** In MaxReceivedRate tests TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- **[Ref] Applicable standard specifications:** RFC2544.
.. only:: html
.. csv-table::
:header-rows: 1
:widths: auto
:align: center
:file: vpp_mrr_results_10ge2p1x520-eth-l2bdbasemaclrn-mrr.csv
.. only:: latex
.. raw:: latex
\csvautolongtable{_tmp/src/detailed_test_results/vpp_mrr_results/vpp_mrr_results_10ge2p1x520-eth-l2bdbasemaclrn-mrr.csv}
10ge2p1x520-eth-l2bdscale100kmaclrn-mrr
```````````````````````````````````````
**Raw results for L2BD test cases**
- **[Top] Network Topologies:** TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- **[Enc] Packet Encapsulations:** Eth-IPv4 for L2 switching of IPv4.
- **[Cfg] DUT configuration:** DUT1 and DUT2 are configured with L2 bridge- domain and MAC learning enabled. DUT1 and DUT2 tested with 2p10GE NI X520 Niantic by Intel.
- **[Ver] TG verification:** In MaxReceivedRate tests TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 50k flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses ranges are incremented as follows: port01_src ca:fe:00:00:00:00 - port01_src ca:fe:00:00:c3:4f, port01_dst fa:ce:00:00:00:00 - port01_dst fa:ce:00:00:c3:4f, port02_src fa:ce:00:00:00:00 - port02_src fa:ce:00:00:c3:4f, port02_dst ca:fe:00:00:00:00 - port02_dst ca:fe:00:00:c3:4f,
- **[Ref] Applicable standard specifications:** RFC2544.
.. only:: html
.. csv-table::
:header-rows: 1
:widths: auto
:align: center
:file: vpp_mrr_results_10ge2p1x520-eth-l2bdscale100kmaclrn-mrr.csv
.. only:: latex
.. raw:: latex
\csvautolongtable{_tmp/src/detailed_test_results/vpp_mrr_results/vpp_mrr_results_10ge2p1x520-eth-l2bdscale100kmaclrn-mrr.csv}
10ge2p1x520-eth-l2bdscale10kmaclrn-mrr
``````````````````````````````````````
**Raw results for L2BD test cases**
- **[Top] Network Topologies:** TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- **[Enc] Packet Encapsulations:** Eth-IPv4 for L2 switching of IPv4.
- **[Cfg] DUT configuration:** DUT1 and DUT2 are configured with L2 bridge- domain and MAC learning enabled. DUT1 and DUT2 tested with 2p10GE NI X520 Niantic by Intel.
- **[Ver] TG verification:** In MaxReceivedRate tests TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 5k flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses ranges are incremented as follows: port01_src ca:fe:00:00:00:00 - port01_src ca:fe:00:00:13:87, port01_dst fa:ce:00:00:00:00 - port01_dst fa:ce:00:00:13:87, port02_src fa:ce:00:00:00:00 - port02_src fa:ce:00:00:13:87, port02_dst ca:fe:00:00:00:00 - port02_dst ca:fe:00:00:13:87,
- **[Ref] Applicable standard specifications:** RFC2544.
.. only:: html
.. csv-table::
:header-rows: 1
:widths: auto
:align: center
:file: vpp_mrr_results_10ge2p1x520-eth-l2bdscale10kmaclrn-mrr.csv
.. only:: latex
.. raw:: latex
\csvautolongtable{_tmp/src/detailed_test_results/vpp_mrr_results/vpp_mrr_results_10ge2p1x520-eth-l2bdscale10kmaclrn-mrr.csv}
10ge2p1x520-eth-l2bdscale1mmaclrn-mrr
`````````````````````````````````````
**Raw results for L2BD test cases**
- **[Top] Network Topologies:** TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- **[Enc] Packet Encapsulations:** Eth-IPv4 for L2 switching of IPv4.
- **[Cfg] DUT configuration:** DUT1 and DUT2 are configured with L2 bridge- domain and MAC learning enabled. DUT1 and DUT2 tested with 2p10GE NI X520 Niantic by Intel.
- **[Ver] TG verification:** In MaxReceivedRate tests TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 500k flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses ranges are incremented as follows: port01_src ca:fe:00:00:00:00 - port01_src ca:fe:00:07:a1:1f, port01_dst fa:ce:00:00:00:00 - port01_dst fa:ce:00:07:a1:1f, port02_src fa:ce:00:00:00:00 - port02_src fa:ce:00:07:a1:1f, port02_dst ca:fe:00:00:00:00 - port02_dst ca:fe:00:07:a1:1f,
- **[Ref] Applicable standard specifications:** RFC2544.
.. only:: html
.. csv-table::
:header-rows: 1
:widths: auto
:align: center
:file: vpp_mrr_results_10ge2p1x520-eth-l2bdscale1mmaclrn-mrr.csv
.. only:: latex
.. raw:: latex
\csvautolongtable{_tmp/src/detailed_test_results/vpp_mrr_results/vpp_mrr_results_10ge2p1x520-eth-l2bdscale1mmaclrn-mrr.csv}
10ge2p1x520-eth-l2xcbase-mrr
````````````````````````````
**Raw results L2XC test cases**
- **[Top] Network Topologies:** TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- **[Enc] Packet Encapsulations:** Eth-IPv4 for L2 cross connect.
- **[Cfg] DUT configuration:** DUT1 and DUT2 are configured with L2 cross- connect. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.
- **[Ver] TG verification:** In MaxReceivedRate tests TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- **[Ref] Applicable standard specifications:** RFC2544.
.. only:: html
.. csv-table::
:header-rows: 1
:widths: auto
:align: center
:file: vpp_mrr_results_10ge2p1x520-eth-l2xcbase-mrr.csv
.. only:: latex
.. raw:: latex
\csvautolongtable{_tmp/src/detailed_test_results/vpp_mrr_results/vpp_mrr_results_10ge2p1x520-eth-l2xcbase-mrr.csv}
10ge2p1x710-dot1q-l2bdbasemaclrn-mrr
````````````````````````````````````
**Raw results L2BD test cases with 802.1q test cases**
- **[Top] Network Topologies:** TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- **[Enc] Packet Encapsulations:** Eth-IPv4 for L2 switching of IPv4. 802.1q tagging is applied on link between DUT1 and DUT2.
- **[Cfg] DUT configuration:** DUT1 and DUT2 are configured with L2 bridge domain and MAC learning enabled. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel.
- **[Ver] TG verification:** In MaxReceivedRate tests TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 254 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- **[Ref] Applicable standard specifications:** RFC2544.
.. only:: html
.. csv-table::
:header-rows: 1
:widths: auto
:align: center
:file: vpp_mrr_results_10ge2p1x710-dot1q-l2bdbasemaclrn-mrr.csv
.. only:: latex
.. raw:: latex
\csvautolongtable{_tmp/src/detailed_test_results/vpp_mrr_results/vpp_mrr_results_10ge2p1x710-dot1q-l2bdbasemaclrn-mrr.csv}
10ge2p1x710-dot1q-l2xcbase-mrr
``````````````````````````````
**Raw results L2XC with 802.1q test cases**
- **[Top] Network Topologies:** TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- **[Enc] Packet Encapsulations:** Eth-IPv4 for L2 cross connect. 802.1q tagging is applied on link between DUT1 and DUT2.
- **[Cfg] DUT configuration:** DUT1 and DUT2 are configured with L2 cross- connect. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel.
- **[Ver] TG verification:** In MaxReceivedRate tests TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- **[Ref] Applicable standard specifications:** RFC2544.
.. only:: html
.. csv-table::
:header-rows: 1
:widths: auto
:align: center
:file: vpp_mrr_results_10ge2p1x710-dot1q-l2xcbase-mrr.csv
.. only:: latex
.. raw:: latex
\csvautolongtable{_tmp/src/detailed_test_results/vpp_mrr_results/vpp_mrr_results_10ge2p1x710-dot1q-l2xcbase-mrr.csv}
10ge2p1x710-eth-l2bdbasemaclrn-iacl1sf-10kflows-mrr
```````````````````````````````````````````````````
**Raw results L2BD test cases with ACL**
- **[Top] Network Topologies:** TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- **[Enc] Packet Encapsulations:** Eth-IPv4-UDP for L2 switching of IPv4.
- **[Cfg] DUT configuration:** DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with 2p10GE NIC X710 by Intel.
- **[Ver] TG verification:** In MaxReceivedRate tests TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- **[Ref] Applicable standard specifications:** RFC2544.
.. only:: html
.. csv-table::
:header-rows: 1
:widths: auto
:align: center
:file: vpp_mrr_results_10ge2p1x710-eth-l2bdbasemaclrn-iacl1sf-10kflows-mrr.csv
.. only:: latex
.. raw:: latex
\csvautolongtable{_tmp/src/detailed_test_results/vpp_mrr_results/vpp_mrr_results_10ge2p1x710-eth-l2bdbasemaclrn-iacl1sf-10kflows-mrr.csv}
10ge2p1x710-eth-l2bdbasemaclrn-iacl1sl-10kflows-mrr
```````````````````````````````````````````````````
**Raw results L2BD test cases with ACL**
- **[Top] Network Topologies:** TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- **[Enc] Packet Encapsulations:** Eth-IPv4-UDP for L2 switching of IPv4.
- **[Cfg] DUT configuration:** DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with 2p10GE NIC X710 by Intel.
- **[Ver] TG verification:** In MaxReceivedRate tests TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- **[Ref] Applicable standard specifications:** RFC2544.
.. only:: html
.. csv-table::
:header-rows: 1
:widths: auto
:align: center
:file: vpp_mrr_results_10ge2p1x710-eth-l2bdbasemaclrn-iacl1sl-10kflows-mrr.csv
.. only:: latex
.. raw:: latex
\csvautolongtable{_tmp/src/detailed_test_results/vpp_mrr_results/vpp_mrr_results_10ge2p1x710-eth-l2bdbasemaclrn-iacl1sl-10kflows-mrr.csv}
10ge2p1x710-eth-l2bdbasemaclrn-iacl50sf-10kflows-mrr
````````````````````````````````````````````````````
**Raw results L2BD test cases with ACL**
- **[Top] Network Topologies:** TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- **[Enc] Packet Encapsulations:** Eth-IPv4-UDP for L2 switching of IPv4.
- **[Cfg] DUT configuration:** DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with 2p10GE NIC X710 by Intel.
- **[Ver] TG verification:** In MaxReceivedRate tests TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- **[Ref] Applicable standard specifications:** RFC2544.
.. only:: html
.. csv-table::
:header-rows: 1
:widths: auto
:align: center
:file: vpp_mrr_results_10ge2p1x710-eth-l2bdbasemaclrn-iacl50sf-10kflows-mrr.csv
.. only:: latex
.. raw:: latex
\csvautolongtable{_tmp/src/detailed_test_results/vpp_mrr_results/vpp_mrr_results_10ge2p1x710-eth-l2bdbasemaclrn-iacl50sf-10kflows-mrr.csv}
10ge2p1x710-eth-l2bdbasemaclrn-iacl50sl-10kflows-mrr
````````````````````````````````````````````````````
**Raw results L2BD test cases with ACL**
- **[Top] Network Topologies:** TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- **[Enc] Packet Encapsulations:** Eth-IPv4-UDP for L2 switching of IPv4.
- **[Cfg] DUT configuration:** DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with 2p10GE NIC X710 by Intel.
- **[Ver] TG verification:** In MaxReceivedRate tests TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- **[Ref] Applicable standard specifications:** RFC2544.
.. only:: html
.. csv-table::
:header-rows: 1
:widths: auto
:align: center
:file: vpp_mrr_results_10ge2p1x710-eth-l2bdbasemaclrn-iacl50sl-10kflows-mrr.csv
.. only:: latex
.. raw:: latex
\csvautolongtable{_tmp/src/detailed_test_results/vpp_mrr_results/vpp_mrr_results_10ge2p1x710-eth-l2bdbasemaclrn-iacl50sl-10kflows-mrr.csv}
10ge2p1x710-eth-l2bdbasemaclrn-mrr
``````````````````````````````````
**Raw results L2BD test cases**
- **[Top] Network Topologies:** TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- **[Enc] Packet Encapsulations:** Eth-IPv4 for L2 switching of IPv4.
- **[Cfg] DUT configuration:** DUT1 and DUT2 are configured with L2 bridge- domain and MAC learning enabled. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel.
- **[Ver] TG verification:** In MaxReceivedRate tests TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- **[Ref] Applicable standard specifications:** RFC2544.
.. only:: html
.. csv-table::
:header-rows: 1
:widths: auto
:align: center
:file: vpp_mrr_results_10ge2p1x710-eth-l2bdbasemaclrn-mrr.csv
.. only:: latex
.. raw:: latex
\csvautolongtable{_tmp/src/detailed_test_results/vpp_mrr_results/vpp_mrr_results_10ge2p1x710-eth-l2bdbasemaclrn-mrr.csv}
10ge2p1x710-eth-l2bdscale100kmaclrn-mrr
```````````````````````````````````````
**Raw results for L2BD test cases**
- **[Top] Network Topologies:** TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- **[Enc] Packet Encapsulations:** Eth-IPv4 for L2 switching of IPv4.
- **[Cfg] DUT configuration:** DUT1 and DUT2 are configured with L2 bridge- domain and MAC learning enabled. DUT1 and DUT2 tested with 2p10GE NI X710 by Intel.
- **[Ver] TG verification:** In MaxReceivedRate tests TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 50k flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses ranges are incremented as follows: port01_src ca:fe:00:00:00:00 - port01_src ca:fe:00:00:c3:4f, port01_dst fa:ce:00:00:00:00 - port01_dst fa:ce:00:00:c3:4f, port02_src fa:ce:00:00:00:00 - port02_src fa:ce:00:00:c3:4f, port02_dst ca:fe:00:00:00:00 - port02_dst ca:fe:00:00:c3:4f,
- **[Ref] Applicable standard specifications:** RFC2544.
.. only:: html
.. csv-table::
:header-rows: 1
:widths: auto
:align: center
:file: vpp_mrr_results_10ge2p1x710-eth-l2bdscale100kmaclrn-mrr.csv
.. only:: latex
.. raw:: latex
\csvautolongtable{_tmp/src/detailed_test_results/vpp_mrr_results/vpp_mrr_results_10ge2p1x710-eth-l2bdscale100kmaclrn-mrr.csv}
10ge2p1x710-eth-l2bdscale10kmaclrn-mrr
``````````````````````````````````````
**Raw results for L2BD test cases**
- **[Top] Network Topologies:** TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- **[Enc] Packet Encapsulations:** Eth-IPv4 for L2 switching of IPv4.
- **[Cfg] DUT configuration:** DUT1 and DUT2 are configured with L2 bridge- domain and MAC learning enabled. DUT1 and DUT2 tested with 2p10GE NI X710 by Intel.
- **[Ver] TG verification:** In MaxReceivedRate tests TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 5k flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses ranges are incremented as follows: port01_src ca:fe:00:00:00:00 - port01_src ca:fe:00:00:13:87, port01_dst fa:ce:00:00:00:00 - port01_dst fa:ce:00:00:13:87, port02_src fa:ce:00:00:00:00 - port02_src fa:ce:00:00:13:87, port02_dst ca:fe:00:00:00:00 - port02_dst ca:fe:00:00:13:87,
- **[Ref] Applicable standard specifications:** RFC2544.
.. only:: html
.. csv-table::
:header-rows: 1
:widths: auto
:align: center
:file: vpp_mrr_results_10ge2p1x710-eth-l2bdscale10kmaclrn-mrr.csv
.. only:: latex
.. raw:: latex
\csvautolongtable{_tmp/src/detailed_test_results/vpp_mrr_results/vpp_mrr_results_10ge2p1x710-eth-l2bdscale10kmaclrn-mrr.csv}
10ge2p1x710-eth-l2bdscale1mmaclrn-mrr
`````````````````````````````````````
**Raw results for L2BD test cases**
- **[Top] Network Topologies:** TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- **[Enc] Packet Encapsulations:** Eth-IPv4 for L2 switching of IPv4.
- **[Cfg] DUT configuration:** DUT1 and DUT2 are configured with L2 bridge- domain and MAC learning enabled. DUT1 and DUT2 tested with 2p10GE NI X710 by Intel.
- **[Ver] TG verification:** In MaxReceivedRate tests TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 500k flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses ranges are incremented as follows: port01_src ca:fe:00:00:00:00 - port01_src ca:fe:00:07:a1:1f, port01_dst fa:ce:00:00:00:00 - port01_dst fa:ce:00:07:a1:1f, port02_src fa:ce:00:00:00:00 - port02_src fa:ce:00:07:a1:1f, port02_dst ca:fe:00:00:00:00 - port02_dst ca:fe:00:07:a1:1f,
- **[Ref] Applicable standard specifications:** RFC2544.
.. only:: html
.. csv-table::
:header-rows: 1
:widths: auto
:align: center
:file: vpp_mrr_results_10ge2p1x710-eth-l2bdscale1mmaclrn-mrr.csv
.. only:: latex
.. raw:: latex
\csvautolongtable{_tmp/src/detailed_test_results/vpp_mrr_results/vpp_mrr_results_10ge2p1x710-eth-l2bdscale1mmaclrn-mrr.csv}
10ge2p1x710-eth-l2xcbase-mrr
````````````````````````````
**Raw results L2XC test cases**
- **[Top] Network Topologies:** TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- **[Enc] Packet Encapsulations:** Eth-IPv4 for L2 cross connect.
- **[Cfg] DUT configuration:** DUT1 and DUT2 are configured with L2 cross- connect. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel.
- **[Ver] TG verification:** In MaxReceivedRate tests TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- **[Ref] Applicable standard specifications:** RFC2544.
.. only:: html
.. csv-table::
:header-rows: 1
:widths: auto
:align: center
:file: vpp_mrr_results_10ge2p1x710-eth-l2xcbase-mrr.csv
.. only:: latex
.. raw:: latex
\csvautolongtable{_tmp/src/detailed_test_results/vpp_mrr_results/vpp_mrr_results_10ge2p1x710-eth-l2xcbase-mrr.csv}
40ge2p1xl710-eth-l2bdbasemaclrn-mrr
```````````````````````````````````
**Raw results L2BD test cases**
- **[Top] Network Topologies:** TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- **[Enc] Packet Encapsulations:** Eth-IPv4 for L2 switching of IPv4.
- **[Cfg] DUT configuration:** DUT1 and DUT2 are configured with L2 bridge- domain and MAC learning enabled. DUT1 and DUT2 tested with 2p40GE NIC XL710-DA2 by Intel.
- **[Ver] TG verification:** In MaxReceivedRate tests TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- **[Ref] Applicable standard specifications:** RFC2544.
.. only:: html
.. csv-table::
:header-rows: 1
:widths: auto
:align: center
:file: vpp_mrr_results_40ge2p1xl710-eth-l2bdbasemaclrn-mrr.csv
.. only:: latex
.. raw:: latex
\csvautolongtable{_tmp/src/detailed_test_results/vpp_mrr_results/vpp_mrr_results_40ge2p1xl710-eth-l2bdbasemaclrn-mrr.csv}
40ge2p1xl710-eth-l2xcbase-mrr
`````````````````````````````
**Raw results L2XC test cases**
- **[Top] Network Topologies:** TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- **[Enc] Packet Encapsulations:** Eth-IPv4 for L2 cross connect.
- **[Cfg] DUT configuration:** DUT1 and DUT2 are configured with L2 cross- connect. DUT1 and DUT2 tested with 2p40GE NIC XL710 by Intel.
- **[Ver] TG verification:** In MaxReceivedRate tests TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- **[Ref] Applicable standard specifications:** RFC2544.
.. only:: html
.. csv-table::
:header-rows: 1
:widths: auto
:align: center
:file: vpp_mrr_results_40ge2p1xl710-eth-l2xcbase-mrr.csv
.. only:: latex
.. raw:: latex
\csvautolongtable{_tmp/src/detailed_test_results/vpp_mrr_results/vpp_mrr_results_40ge2p1xl710-eth-l2xcbase-mrr.csv}
vm vhost
--------
10ge2p1x520-dot1q-l2bdbasemaclrn-eth-2vhostvr1024-1vm-mrr
`````````````````````````````````````````````````````````
**Raw results L2BD test cases with vhost**
- **[Top] Network Topologies:** TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- **[Enc] Packet Encapsulations:** Eth-IPv4 for L2 switching of IPv4. 802.1q tagging is applied on link between DUT1 and DUT2.
- **[Cfg] DUT configuration:** DUT1 and DUT2 are configured with L2 bridge- domain and MAC learning enabled. Qemu Guest is connected to VPP via vhost-user interfaces. Guest is running DPDK testpmd interconnecting vhost-user interfaces using 5 cores pinned to cpus 5-9 and 2048M memory. Testpmd is using socket-mem=1024M (512x2M hugepages), 5 cores (1 main core and 4 cores dedicated for io), forwarding mode is set to io, rxd/txd=1024, burst=64. DUT1, DUT2 are tested with 2p10GE NIC X520 Niantic by Intel.
- **[Ver] TG verification:** In MaxReceivedRate test TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 254 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
.. only:: html
.. csv-table::
:header-rows: 1
:widths: auto
:align: center
:file: vpp_mrr_results_10ge2p1x520-dot1q-l2bdbasemaclrn-eth-2vhostvr1024-1vm-mrr.csv
.. only:: latex
.. raw:: latex
\csvautolongtable{_tmp/src/detailed_test_results/vpp_mrr_results/vpp_mrr_results_10ge2p1x520-dot1q-l2bdbasemaclrn-eth-2vhostvr1024-1vm-mrr.csv}
10ge2p1x520-dot1q-l2xcbase-eth-2vhostvr1024-1vm-mrr
```````````````````````````````````````````````````
**Raw results L2XC test cases with vhost**
- **[Top] Network Topologies:** TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- **[Enc] Packet Encapsulations:** Eth-IPv4 for L2 cross connect. 802.1q tagging is applied on link between DUT1 and DUT2.
- **[Cfg] DUT configuration:** DUT1 and DUT2 are configured with L2 cross- connect. Qemu Guest is connected to VPP via vhost-user interfaces. Guest is running DPDK testpmd interconnecting vhost-user interfaces using 5 cores pinned to cpus 5-9 and 2048M memory. Testpmd is using socket-mem=1024M (512x2M hugepages), 5 cores (1 main core and 4 cores dedicated for io), forwarding mode is set to io, rxd/txd=1024, burst=64. DUT1, DUT2 are tested with 2p10GE NIC X520 Niantic by Intel.
- **[Ver] TG verification:** In MaxReceivedRate test TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 254 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
.. only:: html
.. csv-table::
:header-rows: 1
:widths: auto
:align: center
:file: vpp_mrr_results_10ge2p1x520-dot1q-l2xcbase-eth-2vhostvr1024-1vm-mrr.csv
.. only:: latex
.. raw:: latex
\csvautolongtable{_tmp/src/detailed_test_results/vpp_mrr_results/vpp_mrr_results_10ge2p1x520-dot1q-l2xcbase-eth-2vhostvr1024-1vm-mrr.csv}
10ge2p1x520-eth-l2bdbasemaclrn-eth-2vhostvr1024-1vm-mrr
```````````````````````````````````````````````````````
**Raw results L2BD test cases with vhost**
- **[Top] Network Topologies:** TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- **[Enc] Packet Encapsulations:** Eth-IPv4 for L2 switching of IPv4.
- **[Cfg] DUT configuration:** DUT1 and DUT2 are configured with L2 bridge- domain and MAC learning enabled. Qemu Guest is connected to VPP via vhost-user interfaces. Guest is running DPDK testpmd interconnecting vhost-user interfaces using 5 cores pinned to cpus 5-9 and 2048M memory. Testpmd is using socket-mem=1024M (512x2M hugepages), 5 cores (1 main core and 4 cores dedicated for io), forwarding mode is set to io, rxd/txd=1024, burst=64. Scheduler policy is set to SCHED_RR with priority 1 for all Qemu CPUs. DUT1, DUT2 are tested with 2p10GE NIC X520 Niantic by Intel.
- **[Ver] TG verification:** In MaxReceivedRate test TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 254 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
.. only:: html
.. csv-table::
:header-rows: 1
:widths: auto
:align: center
:file: vpp_mrr_results_10ge2p1x520-eth-l2bdbasemaclrn-eth-2vhostvr1024-1vm-mrr.csv
.. only:: latex
.. raw:: latex
\csvautolongtable{_tmp/src/detailed_test_results/vpp_mrr_results/vpp_mrr_results_10ge2p1x520-eth-l2bdbasemaclrn-eth-2vhostvr1024-1vm-mrr.csv}
10ge2p1x520-eth-l2bdbasemaclrn-eth-2vhostvr256-1vm-mrr
``````````````````````````````````````````````````````
**Raw results L2BD test cases with vhost**
- **[Top] Network Topologies:** TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- **[Enc] Packet Encapsulations:** Eth-IPv4 for L2 switching of IPv4.
- **[Cfg] DUT configuration:** DUT1 and DUT2 are configured with L2 bridge- domain and MAC learning enabled. Qemu Guest is connected to VPP via vhost-user interfaces. Guest is running DPDK testpmd interconnecting vhost-user interfaces using 5 cores pinned to cpus 5-9 and 2048M memory. Testpmd is using socket-mem=1024M (512x2M hugepages), 5 cores (1 main core and 4 cores dedicated for io), forwarding mode is set to io, rxd/txd=256, burst=64. Scheduler policy is set to SCHED_RR with priority 1 for all Qemu CPUs. DUT1, DUT2 are tested with 2p10GE NIC X520 Niantic by Intel.
- **[Ver] TG verification:** In MaxReceivedRate test TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 254 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
.. only:: html
.. csv-table::
:header-rows: 1
:widths: auto
:align: center
:file: vpp_mrr_results_10ge2p1x520-eth-l2bdbasemaclrn-eth-2vhostvr256-1vm-mrr.csv
.. only:: latex
.. raw:: latex
\csvautolongtable{_tmp/src/detailed_test_results/vpp_mrr_results/vpp_mrr_results_10ge2p1x520-eth-l2bdbasemaclrn-eth-2vhostvr256-1vm-mrr.csv}
10ge2p1x520-eth-l2bdbasemaclrn-eth-4vhostvr1024-2vm-mrr
```````````````````````````````````````````````````````
**Raw results L2BD test cases with vhost**
- **[Top] Network Topologies:** TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- **[Enc] Packet Encapsulations:** Eth-IPv4 for L2 switching of IPv4.
- **[Cfg] DUT configuration:** DUT1 and DUT2 are configured with L2 bridge- domains and MAC learning enabled. Qemu Guests are connected to VPP via vhost-user interfaces. Guests are running DPDK testpmd interconnecting vhost-user interfaces using 5 cores pinned to cpus 6-10 and 11-15 and 2048M memory. Testpmd is using socket-mem=1024M (512x2M hugepages), 5 cores (1 main core and 4 cores dedicated for io), forwarding mode is set to io, rxd/txd=1024, burst=64. DUT1, DUT2 are tested with 2p10GE NIC X520 Niantic by Intel.
- **[Ver] TG verification:** In MaxReceivedRate test TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 254 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
.. only:: html
.. csv-table::
:header-rows: 1
:widths: auto
:align: center
:file: vpp_mrr_results_10ge2p1x520-eth-l2bdbasemaclrn-eth-4vhostvr1024-2vm-mrr.csv
.. only:: latex
.. raw:: latex
\csvautolongtable{_tmp/src/detailed_test_results/vpp_mrr_results/vpp_mrr_results_10ge2p1x520-eth-l2bdbasemaclrn-eth-4vhostvr1024-2vm-mrr.csv}
10ge2p1x520-eth-l2xcbase-eth-2vhostvr1024-1vm-mrr
`````````````````````````````````````````````````
**Raw results L2XC test cases with vhost**
- **[Top] Network Topologies:** TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- **[Enc] Packet Encapsulations:** Eth-IPv4 for L2 switching of IPv4. 802.1q tagging is applied on link between DUT1 and DUT2.
- **[Cfg] DUT configuration:** DUT1 and DUT2 are configured with L2 cross- connect. Qemu Guest is connected to VPP via vhost-user interfaces. Guest is running DPDK testpmd interconnecting vhost-user interfaces using 5 cores pinned to cpus 5-9 and 2048M memory. Testpmd is using socket-mem=1024M (512x2M hugepages), 5 cores (1 main core and 4 cores dedicated for io), forwarding mode is set to io, rxd/txd=1024, burst=64. DUT1, DUT2 are tested with 2p10GE NIC X520 Niantic by Intel.
- **[Ver] TG verification:** In MaxReceivedRate test TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 254 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
.. only:: html
.. csv-table::
:header-rows: 1
:widths: auto
:align: center
:file: vpp_mrr_results_10ge2p1x520-eth-l2xcbase-eth-2vhostvr1024-1vm-mrr.csv
.. only:: latex
.. raw:: latex
\csvautolongtable{_tmp/src/detailed_test_results/vpp_mrr_results/vpp_mrr_results_10ge2p1x520-eth-l2xcbase-eth-2vhostvr1024-1vm-mrr.csv}
10ge2p1x520-eth-l2xcbase-eth-2vhostvr256-1vm-mrr
````````````````````````````````````````````````
**Raw results L2XC test cases with vhost**
- **[Top] Network Topologies:** TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- **[Enc] Packet Encapsulations:** Eth-IPv4 for L2 switching of IPv4. 802.1q tagging is applied on link between DUT1 and DUT2.
- **[Cfg] DUT configuration:** DUT1 and DUT2 are configured with L2 cross- connect. Qemu Guest is connected to VPP via vhost-user interfaces. Guest is running DPDK testpmd interconnecting vhost-user interfaces using 5 cores pinned to cpus 5-9 and 2048M memory. Testpmd is using socket-mem=1024M (512x2M hugepages), 5 cores (1 main core and 4 cores dedicated for io), forwarding mode is set to io, rxd/txd=256, burst=64. DUT1, DUT2 are tested with 2p10GE NIC X520 Niantic by Intel.
- **[Ver] TG verification:** In MaxReceivedRate test TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 254 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
.. only:: html
.. csv-table::
:header-rows: 1
:widths: auto
:align: center
:file: vpp_mrr_results_10ge2p1x520-eth-l2xcbase-eth-2vhostvr256-1vm-mrr.csv
.. only:: latex
.. raw:: latex
\csvautolongtable{_tmp/src/detailed_test_results/vpp_mrr_results/vpp_mrr_results_10ge2p1x520-eth-l2xcbase-eth-2vhostvr256-1vm-mrr.csv}
10ge2p1x520-eth-l2xcbase-eth-4vhostvr1024-2vm-mrr
`````````````````````````````````````````````````
**Raw results L2XC test cases with vhost**
- **[Top] Network Topologies:** TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- **[Enc] Packet Encapsulations:** Eth-IPv4 for L2 switching of IPv4. 802.1q tagging is applied on link between DUT1 and DUT2.
- **[Cfg] DUT configuration:** DUT1 and DUT2 are configured with L2 cross- connects. Qemu Guests are connected to VPP via vhost-user interfaces. Guests are running DPDK testpmd interconnecting vhost-user interfaces using 5 cores pinned to cpus 6-10 and 11-15 and 2048M memory. Testpmd is using socket-mem=1024M (512x2M hugepages), 5 cores (1 main core and 4 cores dedicated for io), forwarding mode is set to io, rxd/txd=1024, burst=64. DUT1, DUT2 are tested with 2p10GE NIC X520 Niantic by Intel.
- **[Ver] TG verification:** In MaxReceivedRate test TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 254 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
.. only:: html
.. csv-table::
:header-rows: 1
:widths: auto
:align: center
:file: vpp_mrr_results_10ge2p1x520-eth-l2xcbase-eth-4vhostvr1024-2vm-mrr.csv
.. only:: latex
.. raw:: latex
\csvautolongtable{_tmp/src/detailed_test_results/vpp_mrr_results/vpp_mrr_results_10ge2p1x520-eth-l2xcbase-eth-4vhostvr1024-2vm-mrr.csv}
10ge2p1x520-ethip4-ip4base-eth-2vhostvr1024-1vm-mrr
```````````````````````````````````````````````````
**Raw results IPv4 test cases with vhost**
- **[Top] Network Topologies:** TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- **[Enc] Packet Encapsulations:** Eth-IPv4 for IPv4 routing.
- **[Cfg] DUT configuration:** DUT1 and DUT2 are configured with IPv4 routing and two static IPv4 /24 route entries. Qemu Guest is connected to VPP via vhost-user interfaces. Guest is running DPDK testpmd interconnecting vhost-user interfaces using 5 cores pinned to cpus 5-9 and 2048M memory. Testpmd is using socket-mem=1024M (512x2M hugepages), 5 cores (1 main core and 4 cores dedicated for io), forwarding mode is set to mac, rxd/txd=1024, burst=64. DUT1, DUT2 are tested with 2p10GE NIC X520 Niantic by Intel.
- **[Ver] TG verification:** In MaxReceivedRate test TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
.. only:: html
.. csv-table::
:header-rows: 1
:widths: auto
:align: center
:file: vpp_mrr_results_10ge2p1x520-ethip4-ip4base-eth-2vhostvr1024-1vm-mrr.csv
.. only:: latex
.. raw:: latex
\csvautolongtable{_tmp/src/detailed_test_results/vpp_mrr_results/vpp_mrr_results_10ge2p1x520-ethip4-ip4base-eth-2vhostvr1024-1vm-mrr.csv}
10ge2p1x520-ethip4-ip4base-eth-2vhostvr256-1vm-mrr
``````````````````````````````````````````````````
**Raw results IPv4 test cases with vhost**
- **[Top] Network Topologies:** TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- **[Enc] Packet Encapsulations:** Eth-IPv4 for IPv4 routing.
- **[Cfg] DUT configuration:** DUT1 and DUT2 are configured with IPv4 routing and two static IPv4 /24 route entries. Qemu Guest is connected to VPP via vhost-user interfaces. Guest is running DPDK testpmd interconnecting vhost-user interfaces using 5 cores pinned to cpus 5-9 and 2048M memory. Testpmd is using socket-mem=1024M (512x2M hugepages), 5 cores (1 main core and 4 cores dedicated for io), forwarding mode is set to mac, rxd/txd=256, burst=64. DUT1, DUT2 are tested with 2p10GE NIC X520 Niantic by Intel.
- **[Ver] TG verification:** In MaxReceivedRate test TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
.. only:: html
.. csv-table::
:header-rows: 1
:widths: auto
:align: center
:file: vpp_mrr_results_10ge2p1x520-ethip4-ip4base-eth-2vhostvr256-1vm-mrr.csv
.. only:: latex
.. raw:: latex
\csvautolongtable{_tmp/src/detailed_test_results/vpp_mrr_results/vpp_mrr_results_10ge2p1x520-ethip4-ip4base-eth-2vhostvr256-1vm-mrr.csv}
10ge2p1x520-ethip4-ip4base-eth-4vhostvr1024-2vm-mrr
```````````````````````````````````````````````````
**Raw results IPv4 test cases with vhost**
- **[Top] Network Topologies:** TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- **[Enc] Packet Encapsulations:** Eth-IPv4 for IPv4 routing.
- **[Cfg] DUT configuration:** DUT1 and DUT2 are configured with IPv4 routing and two static IPv4 /24 route entries. Qemu Guests are connected to VPP via vhost-user interfaces. Guests are running DPDK testpmd interconnectingvhost-user interfaces using 5 cores pinned to cpus 6-10 and 11-15 and 2048M memory. Testpmd is using socket-mem=1024M (512x2M hugepages), 5 cores (1 main core and 4 cores dedicated for io), forwarding mode is set to io, rxd/txd=1024, burst=64. DUT1, DUT2 are tested with 2p10GE NIC X520 Niantic by Intel.
- **[Ver] TG verification:** In MaxReceivedRate test TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
.. only:: html
.. csv-table::
:header-rows: 1
:widths: auto
:align: center
:file: vpp_mrr_results_10ge2p1x520-ethip4-ip4base-eth-4vhostvr1024-2vm-mrr.csv
.. only:: latex
.. raw:: latex
\csvautolongtable{_tmp/src/detailed_test_results/vpp_mrr_results/vpp_mrr_results_10ge2p1x520-ethip4-ip4base-eth-4vhostvr1024-2vm-mrr.csv}
10ge2p1x520-ethip4vxlan-l2bdbasemaclrn-eth-2vhostvr1024-1vm-mrr
```````````````````````````````````````````````````````````````
**Raw results L2BD test cases with VXLANoIPv4 and vhost**
- **[Top] Network Topologies:** TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- **[Enc] Packet Encapsulations:** Eth-IPv4 for L2 switching of IPv4. Eth-IPv4-VXLAN-Eth-IPv4 is applied on link between DUT1 and DUT2.
- **[Cfg] DUT configuration:** DUT1 and DUT2 are configured with L2 bridge- domain and MAC learning enabled. Qemu Guest is connected to VPP via vhost-user interfaces. Guest is running DPDK testpmd interconnecting vhost-user interfaces using 5 cores pinned to cpus 5-9 and 2048M memory. Testpmd is using socket-mem=1024M (512x2M hugepages), 5 cores (1 main core and 4 cores dedicated for io), forwarding mode is set to io, rxd/txd=1024, burst=64. DUT1, DUT2 are tested with 2p10GE NIC X520 Niantic by Intel.
- **[Ver] TG verification:** In MaxReceivedRate test TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 254 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- **[Ref] Applicable standard specifications:** RFC7348.
.. only:: html
.. csv-table::
:header-rows: 1
:widths: auto
:align: center
:file: vpp_mrr_results_10ge2p1x520-ethip4vxlan-l2bdbasemaclrn-eth-2vhostvr1024-1vm-mrr.csv
.. only:: latex
.. raw:: latex
\csvautolongtable{_tmp/src/detailed_test_results/vpp_mrr_results/vpp_mrr_results_10ge2p1x520-ethip4vxlan-l2bdbasemaclrn-eth-2vhostvr1024-1vm-mrr.csv}
10ge2p1x710-dot1q-l2bdbasemaclrn-eth-2vhostvr1024-1vm-mrr
`````````````````````````````````````````````````````````
**Raw results L2BD test cases with vhost**
- **[Top] Network Topologies:** TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- **[Enc] Packet Encapsulations:** Eth-IPv4 for L2 switching of IPv4. 802.1q tagging is applied on link between DUT1 and DUT2.
- **[Cfg] DUT configuration:** DUT1 and DUT2 are configured with L2 bridge- domain and MAC learning enabled. Qemu Guest is connected to VPP via vhost-user interfaces. Guest is running DPDK testpmd interconnecting vhost-user interfaces using 5 cores pinned to cpus 5-9 and 2048M memory. Testpmd is using socket-mem=1024M (512x2M hugepages), 5 cores (1 main core and 4 cores dedicated for io), forwarding mode is set to io, rxd/txd=1024, burst=64. DUT1, DUT2 are tested with 2p10GE NIC X710 by Intel.
- **[Ver] TG verification:** In MaxReceivedRate test TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 254 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
.. only:: html
.. csv-table::
:header-rows: 1
:widths: auto
:align: center
:file: vpp_mrr_results_10ge2p1x710-dot1q-l2bdbasemaclrn-eth-2vhostvr1024-1vm-mrr.csv
.. only:: latex
.. raw:: latex
\csvautolongtable{_tmp/src/detailed_test_results/vpp_mrr_results/vpp_mrr_results_10ge2p1x710-dot1q-l2bdbasemaclrn-eth-2vhostvr1024-1vm-mrr.csv}
10ge2p1x710-dot1q-l2xcbase-eth-2vhostvr1024-1vm-mrr
```````````````````````````````````````````````````
**Raw results L2XC test cases with vhost**
- **[Top] Network Topologies:** TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- **[Enc] Packet Encapsulations:** Eth-IPv4 for L2 cross connect. 802.1q tagging is applied on link between DUT1 and DUT2.
- **[Cfg] DUT configuration:** DUT1 and DUT2 are configured with L2 cross- connect. Qemu Guest is connected to VPP via vhost-user interfaces. Guest is running DPDK testpmd interconnecting vhost-user interfaces using 5 cores pinned to cpus 5-9 and 2048M memory. Testpmd is using socket-mem=1024M (512x2M hugepages), 5 cores (1 main core and 4 cores dedicated for io), forwarding mode is set to io, rxd/txd=1024, burst=64. DUT1, DUT2 are tested with 2p10GE NIC X710 by Intel.
- **[Ver] TG verification:** In MaxReceivedRate test TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 254 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
.. only:: html
.. csv-table::
:header-rows: 1
:widths: auto
:align: center
:file: vpp_mrr_results_10ge2p1x710-dot1q-l2xcbase-eth-2vhostvr1024-1vm-mrr.csv
.. only:: latex
.. raw:: latex
\csvautolongtable{_tmp/src/detailed_test_results/vpp_mrr_results/vpp_mrr_results_10ge2p1x710-dot1q-l2xcbase-eth-2vhostvr1024-1vm-mrr.csv}
10ge2p1x710-eth-l2bdbasemaclrn-eth-2vhostvr256-1vm-mrr
``````````````````````````````````````````````````````
**Raw results L2BD test cases with vhost**
- **[Top] Network Topologies:** TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- **[Enc] Packet Encapsulations:** Eth-IPv4 for L2 switching of IPv4.
- **[Cfg] DUT configuration:** DUT1 and DUT2 are configured with L2 bridge- domain and MAC learning enabled. Qemu Guest is connected to VPP via vhost-user interfaces. Guest is running DPDK testpmd interconnecting vhost-user interfaces using 5 cores pinned to cpus 5-9 and 2048M memory. Testpmd is using socket-mem=1024M (512x2M hugepages), 5 cores (1 main core and 4 cores dedicated for io), forwarding mode is set to io, rxd/txd=256, burst=64. Scheduler policy is set to SCHED_RR with priority 1 for all Qemu CPUs. DUT1, DUT2 are tested with 2p10GE NIC X710 by Intel.
- **[Ver] TG verification:** In MaxReceivedRate test TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 254 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
.. only:: html
.. csv-table::
:header-rows: 1
:widths: auto
:align: center
:file: vpp_mrr_results_10ge2p1x710-eth-l2bdbasemaclrn-eth-2vhostvr256-1vm-mrr.csv
.. only:: latex
.. raw:: latex
\csvautolongtable{_tmp/src/detailed_test_results/vpp_mrr_results/vpp_mrr_results_10ge2p1x710-eth-l2bdbasemaclrn-eth-2vhostvr256-1vm-mrr.csv}
10ge2p1x710-eth-l2bdbasemaclrn-eth-4vhostvr1024-2vm-mrr
```````````````````````````````````````````````````````
**Raw results L2BD test cases with vhost**
- **[Top] Network Topologies:** TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- **[Enc] Packet Encapsulations:** Eth-IPv4 for L2 switching of IPv4.
- **[Cfg] DUT configuration:** DUT1 and DUT2 are configured with L2 bridge- domains and MAC learning enabled. Qemu Guests are connected to VPP via vhost-user interfaces. Guests are running DPDK testpmd interconnecting vhost-user interfaces using 5 cores pinned to cpus 6-10 and 11-15 and 2048M memory. Testpmd is using socket-mem=1024M (512x2M hugepages), 5 cores (1 main core and 4 cores dedicated for io), forwarding mode is set to io, rxd/txd=1024, burst=64. DUT1, DUT2 are tested with 2p10GE NIC X710 by Intel.
- **[Ver] TG verification:** In MaxReceivedRate test TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 254 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
.. only:: html
.. csv-table::
:header-rows: 1
:widths: auto
:align: center
:file: vpp_mrr_results_10ge2p1x710-eth-l2bdbasemaclrn-eth-4vhostvr1024-2vm-mrr.csv
.. only:: latex
.. raw:: latex
\csvautolongtable{_tmp/src/detailed_test_results/vpp_mrr_results/vpp_mrr_results_10ge2p1x710-eth-l2bdbasemaclrn-eth-4vhostvr1024-2vm-mrr.csv}
10ge2p1x710-eth-l2xcbase-eth-2vhostvr1024-1vm-mrr
`````````````````````````````````````````````````
**Raw results L2XC test cases with vhost**
- **[Top] Network Topologies:** TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- **[Enc] Packet Encapsulations:** Eth-IPv4 for L2 switching of IPv4. 802.1q tagging is applied on link between DUT1 and DUT2.
- **[Cfg] DUT configuration:** DUT1 and DUT2 are configured with L2 cross- connect. Qemu Guest is connected to VPP via vhost-user interfaces. Guest is running DPDK testpmd interconnecting vhost-user interfaces using 5 cores pinned to cpus 5-9 and 2048M memory. Testpmd is using socket-mem=1024M (512x2M hugepages), 5 cores (1 main core and 4 cores dedicated for io), forwarding mode is set to io, rxd/txd=1024, burst=64. DUT1, DUT2 are tested with 2p10GE NIC X710 by Intel.
- **[Ver] TG verification:** In MaxReceivedRate test TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 254 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
.. only:: html
.. csv-table::
:header-rows: 1
:widths: auto
:align: center
:file: vpp_mrr_results_10ge2p1x710-eth-l2xcbase-eth-2vhostvr1024-1vm-mrr.csv
.. only:: latex
.. raw:: latex
\csvautolongtable{_tmp/src/detailed_test_results/vpp_mrr_results/vpp_mrr_results_10ge2p1x710-eth-l2xcbase-eth-2vhostvr1024-1vm-mrr.csv}
10ge2p1x710-eth-l2xcbase-eth-2vhostvr256-1vm-mrr
````````````````````````````````````````````````
**Raw results L2XC test cases with vhost**
- **[Top] Network Topologies:** TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- **[Enc] Packet Encapsulations:** Eth-IPv4 for L2 switching of IPv4. 802.1q tagging is applied on link between DUT1 and DUT2.
- **[Cfg] DUT configuration:** DUT1 and DUT2 are configured with L2 cross- connect. Qemu Guest is connected to VPP via vhost-user interfaces. Guest is running DPDK testpmd interconnecting vhost-user interfaces using 5 cores pinned to cpus 5-9 and 2048M memory. Testpmd is using socket-mem=1024M (512x2M hugepages), 5 cores (1 main core and 4 cores dedicated for io), forwarding mode is set to io, rxd/txd=256, burst=64. DUT1, DUT2 are tested with 2p10GE NIC X710 by Intel.
- **[Ver] TG verification:** In MaxReceivedRate test TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 254 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
.. only:: html
.. csv-table::
:header-rows: 1
:widths: auto
:align: center
:file: vpp_mrr_results_10ge2p1x710-eth-l2xcbase-eth-2vhostvr256-1vm-mrr.csv
.. only:: latex
.. raw:: latex
\csvautolongtable{_tmp/src/detailed_test_results/vpp_mrr_results/vpp_mrr_results_10ge2p1x710-eth-l2xcbase-eth-2vhostvr256-1vm-mrr.csv}
10ge2p1x710-eth-l2xcbase-eth-4vhostvr1024-2vm-mrr
`````````````````````````````````````````````````
**Raw results L2XC test cases with vhost**
- **[Top] Network Topologies:** TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- **[Enc] Packet Encapsulations:** Eth-IPv4 for L2 switching of IPv4. 802.1q tagging is applied on link between DUT1 and DUT2.
- **[Cfg] DUT configuration:** DUT1 and DUT2 are configured with L2 cross- connects. Qemu Guests are connected to VPP via vhost-user interfaces. Guests are running DPDK testpmd interconnecting vhost-user interfaces using 5 cores pinned to cpus 6-10 and 11-15 and 2048M memory. Testpmd is using socket-mem=1024M (512x2M hugepages), 5 cores (1 main core and 4 cores dedicated for io), forwarding mode is set to io, rxd/txd=1024, burst=64. DUT1, DUT2 are tested with 2p10GE NIC X710 by Intel.
- **[Ver] TG verification:** In MaxReceivedRate test TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 254 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
.. only:: html
.. csv-table::
:header-rows: 1
:widths: auto
:align: center
:file: vpp_mrr_results_10ge2p1x710-eth-l2xcbase-eth-4vhostvr1024-2vm-mrr.csv
.. only:: latex
.. raw:: latex
\csvautolongtable{_tmp/src/detailed_test_results/vpp_mrr_results/vpp_mrr_results_10ge2p1x710-eth-l2xcbase-eth-4vhostvr1024-2vm-mrr.csv}
10ge2p1x710-ethip4-ip4base-eth-2vhostvr1024-1vm-mrr
```````````````````````````````````````````````````
**Raw results IPv4 test cases with vhost**
- **[Top] Network Topologies:** TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- **[Enc] Packet Encapsulations:** Eth-IPv4 for IPv4 routing.
- **[Cfg] DUT configuration:** DUT1 and DUT2 are configured with IPv4 routing and two static IPv4 /24 route entries. Qemu Guest is connected to VPP via vhost-user interfaces. Guest is running DPDK testpmd interconnecting vhost-user interfaces using 5 cores pinned to cpus 5-9 and 2048M memory. Testpmd is using socket-mem=1024M (512x2M hugepages), 5 cores (1 main core and 4 cores dedicated for io), forwarding mode is set to mac, rxd/txd=1024, burst=64. DUT1, DUT2 are tested with 2p10GE NIC X710 by Intel.
- **[Ver] TG verification:** In MaxReceivedRate test TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
.. only:: html
.. csv-table::
:header-rows: 1
:widths: auto
:align: center
:file: vpp_mrr_results_10ge2p1x710-ethip4-ip4base-eth-2vhostvr1024-1vm-mrr.csv
.. only:: latex
.. raw:: latex
\csvautolongtable{_tmp/src/detailed_test_results/vpp_mrr_results/vpp_mrr_results_10ge2p1x710-ethip4-ip4base-eth-2vhostvr1024-1vm-mrr.csv}
10ge2p1x710-ethip4-ip4base-eth-2vhostvr256-1vm-mrr
``````````````````````````````````````````````````
**Raw results IPv4 test cases with vhost**
- **[Top] Network Topologies:** TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- **[Enc] Packet Encapsulations:** Eth-IPv4 for IPv4 routing.
- **[Cfg] DUT configuration:** DUT1 and DUT2 are configured with IPv4 routing and two static IPv4 /24 route entries. Qemu Guest is connected to VPP via vhost-user interfaces. Guest is running DPDK testpmd interconnecting vhost-user interfaces using 5 cores pinned to cpus 5-9 and 2048M memory. Testpmd is using socket-mem=1024M (512x2M hugepages), 5 cores (1 main core and 4 cores dedicated for io), forwarding mode is set to mac, rxd/txd=256, burst=64. DUT1, DUT2 are tested with 2p10GE NIC X710 by Intel.
- **[Ver] TG verification:** In MaxReceivedRate test TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
.. only:: html
.. csv-table::
:header-rows: 1
:widths: auto
:align: center
:file: vpp_mrr_results_10ge2p1x710-ethip4-ip4base-eth-2vhostvr256-1vm-mrr.csv
.. only:: latex
.. raw:: latex
\csvautolongtable{_tmp/src/detailed_test_results/vpp_mrr_results/vpp_mrr_results_10ge2p1x710-ethip4-ip4base-eth-2vhostvr256-1vm-mrr.csv}
10ge2p1x710-ethip4-ip4base-eth-4vhostvr1024-2vm-mrr
```````````````````````````````````````````````````
**Raw results IPv4 test cases with vhost**
- **[Top] Network Topologies:** TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- **[Enc] Packet Encapsulations:** Eth-IPv4 for IPv4 routing.
- **[Cfg] DUT configuration:** DUT1 and DUT2 are configured with IPv4 routing and two static IPv4 /24 route entries. Qemu Guests are connected to VPP via vhost-user interfaces. Guests are running DPDK testpmd interconnectingvhost-user interfaces using 5 cores pinned to cpus 6-10 and 11-15 and 2048M memory. Testpmd is using socket-mem=1024M (512x2M hugepages), 5 cores (1 main core and 4 cores dedicated for io), forwarding mode is set to io, rxd/txd=1024, burst=64. DUT1, DUT2 are tested with 2p10GE NIC X710 by Intel.
- **[Ver] TG verification:** In MaxReceivedRate test TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
.. only:: html
.. csv-table::
:header-rows: 1
:widths: auto
:align: center
:file: vpp_mrr_results_10ge2p1x710-ethip4-ip4base-eth-4vhostvr1024-2vm-mrr.csv
.. only:: latex
.. raw:: latex
\csvautolongtable{_tmp/src/detailed_test_results/vpp_mrr_results/vpp_mrr_results_10ge2p1x710-ethip4-ip4base-eth-4vhostvr1024-2vm-mrr.csv}
10ge2p1x710-ethip4vxlan-l2bdbasemaclrn-eth-2vhostvr1024-1vm-mrr
```````````````````````````````````````````````````````````````
**Raw results L2BD test cases with VXLANoIPv4 and vhost**
- **[Top] Network Topologies:** TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- **[Enc] Packet Encapsulations:** Eth-IPv4 for L2 switching of IPv4. Eth-IPv4-VXLAN-Eth-IPv4 is applied on link between DUT1 and DUT2.
- **[Cfg] DUT configuration:** DUT1 and DUT2 are configured with L2 bridge- domain and MAC learning enabled. Qemu Guest is connected to VPP via vhost-user interfaces. Guest is running DPDK testpmd interconnecting vhost-user interfaces using 5 cores pinned to cpus 5-9 and 2048M memory. Testpmd is using socket-mem=1024M (512x2M hugepages), 5 cores (1 main core and 4 cores dedicated for io), forwarding mode is set to io, rxd/txd=1024, burst=64. DUT1, DUT2 are tested with 2p10GE NIC X710 by Intel.
- **[Ver] TG verification:** In MaxReceivedRate test TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 254 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- **[Ref] Applicable standard specifications:** RFC7348.
.. only:: html
.. csv-table::
:header-rows: 1
:widths: auto
:align: center
:file: vpp_mrr_results_10ge2p1x710-ethip4vxlan-l2bdbasemaclrn-eth-2vhostvr1024-1vm-mrr.csv
.. only:: latex
.. raw:: latex
\csvautolongtable{_tmp/src/detailed_test_results/vpp_mrr_results/vpp_mrr_results_10ge2p1x710-ethip4vxlan-l2bdbasemaclrn-eth-2vhostvr1024-1vm-mrr.csv}
40ge2p1x710-eth-l2bdbasemaclrn-eth-2vhostvr1024-1vm-mrr
```````````````````````````````````````````````````````
**Raw results L2BD test cases with vhost**
- **[Top] Network Topologies:** TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- **[Enc] Packet Encapsulations:** Eth-IPv4 for L2 switching of IPv4.
- **[Cfg] DUT configuration:** DUT1 and DUT2 are configured with L2 bridge- domain and MAC learning enabled. Qemu Guests are connected to VPP via vhost-user interfaces. Guests are running DPDK testpmd interconnecting vhost-user interfaces using 5 cores pinned to cpus on NUMA1 and 2048M memory. Testpmd is using socket-mem=1024M (512x2M hugepages), 5 cores (1 main core and 4 cores dedicated for io), forwarding mode is set to io, rxd/txd=1024, burst=64. DUT1, DUT2 are tested with 2p10GE NIC X710 by Intel.
- **[Ver] TG verification:** In MaxReceivedRate test TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
.. only:: html
.. csv-table::
:header-rows: 1
:widths: auto
:align: center
:file: vpp_mrr_results_40ge2p1x710-eth-l2bdbasemaclrn-eth-2vhostvr1024-1vm-mrr.csv
.. only:: latex
.. raw:: latex
\csvautolongtable{_tmp/src/detailed_test_results/vpp_mrr_results/vpp_mrr_results_40ge2p1x710-eth-l2bdbasemaclrn-eth-2vhostvr1024-1vm-mrr.csv}
40ge2p1xl710-eth-l2bdbasemaclrn-eth-2vhostvr1024-1vm-mrr
````````````````````````````````````````````````````````
**Raw results L2BD test cases with vhost**
- **[Top] Network Topologies:** TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- **[Enc] Packet Encapsulations:** Eth-IPv4 for L2 switching of IPv4.
- **[Cfg] DUT configuration:** DUT1 and DUT2 are configured with L2 bridge- domain and MAC learning enabled. Qemu Guests are connected to VPP via vhost-user interfaces. Guests are running DPDK testpmd interconnecting vhost-user interfaces using 5 cores pinned to cpus on NUMA1 and 2048M memory. Testpmd is using socket-mem=1024M (512x2M hugepages), 5 cores (1 main core and 4 cores dedicated for io), forwarding mode is set to io, rxd/txd=1024, burst=64. DUT1, DUT2 are tested with 2p40GE NIC XL710 by Intel.
- **[Ver] TG verification:** In MaxReceivedRate test TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
.. only:: html
.. csv-table::
:header-rows: 1
:widths: auto
:align: center
:file: vpp_mrr_results_40ge2p1xl710-eth-l2bdbasemaclrn-eth-2vhostvr1024-1vm-mrr.csv
.. only:: latex
.. raw:: latex
\csvautolongtable{_tmp/src/detailed_test_results/vpp_mrr_results/vpp_mrr_results_40ge2p1xl710-eth-l2bdbasemaclrn-eth-2vhostvr1024-1vm-mrr.csv}
40ge2p1xl710-eth-l2bdbasemaclrn-eth-4vhostvr1024-2vm-mrr
````````````````````````````````````````````````````````
**Raw results L2BD test cases with vhost**
- **[Top] Network Topologies:** TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- **[Enc] Packet Encapsulations:** Eth-IPv4 for L2 switching of IPv4.
- **[Cfg] DUT configuration:** DUT1 and DUT2 are configured with L2 bridge- domain and MAC learning enabled. Qemu Guests are connected to VPP via vhost-user interfaces. Guests are running DPDK testpmd interconnecting vhost-user interfaces using 5 cores pinned to cpus on NUMA1 and 2048M memory. Testpmd is using socket-mem=1024M (512x2M hugepages), 5 cores (1 main core and 4 cores dedicated for io), forwarding mode is set to io, rxd/txd=1024, burst=64. DUT1, DUT2 are tested with 2p40GE NIC XL710 by Intel.
- **[Ver] TG verification:** In MaxReceivedRate test TG sends traffic at line rate and reports total received/sent packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
.. only:: html
.. csv-table::
:header-rows: 1
:widths: auto
:align: center
:file: vpp_mrr_results_40ge2p1xl710-eth-l2bdbasemaclrn-eth-4vhostvr1024-2vm-mrr.csv
.. only:: latex
.. raw:: latex
\csvautolongtable{_tmp/src/detailed_test_results/vpp_mrr_results/vpp_mrr_results_40ge2p1xl710-eth-l2bdbasemaclrn-eth-4vhostvr1024-2vm-mrr.csv}