9.3.1. 10ge2p1x520-eth-l2xcbase-testpmd-ndrpdrdisc

RFC2544: Pkt throughput IPv4 routing test cases

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv4 for L2 frame forwarding.
  • [Cfg] DUT configuration: DUT1 and DUT2 run the DPDK testpmd application and use the io forwarding mode. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
  • [Ref] Applicable standard specifications: RFC2544.
Name Documentation Status
tc01-64b-1t1c-eth-l2xcbase-testpmd-ndrdisc [Cfg] DUT runs L2 frame forwarding config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
FINAL_RATE: 25835713.625 pps (2x 12917856.8125 pps)
FINAL_BANDWIDTH: 17.361599556 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘10/29/41’, ‘10/30/45’]
LAT_50%NDR: [‘10/14/106’, ‘10/14/98’]
LAT_10%NDR: [‘10/16/38’, ‘10/16/38’]
tc02-64b-1t1c-eth-l2xcbase-testpmd-pdrdisc [Cfg] DUT runs L2 frame forwarding config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
FINAL_RATE: 25835713.625 pps (2x 12917856.8125 pps)
FINAL_BANDWIDTH: 17.361599556 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘10/29/39’, ‘10/29/42’]
LOSS_ACCEPTANCE: 0.5 percentage
tc03-1518b-1t1c-eth-l2xcbase-testpmd-ndrdisc [Cfg] DUT runs L2 frame forwarding config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/238/243’, ‘10/250/271’]
LAT_50%NDR: [‘10/26/134’, ‘10/23/156’]
LAT_10%NDR: [‘10/24/94’, ‘10/25/79’]
tc04-1518b-1t1c-eth-l2xcbase-testpmd-pdrdisc [Cfg] DUT runs L2 frame forwarding config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/244/259’, ‘20/254/276’]
LOSS_ACCEPTANCE: 0.5 percentage
tc05-9000b-1t1c-eth-l2xcbase-testpmd-ndrdisc [Cfg] DUT runs L2 frame forwarding config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘50/233/241’, ‘50/282/295’]
LAT_50%NDR: [‘50/65/197’, ‘50/64/198’]
LAT_10%NDR: [‘50/60/155’, ‘50/60/149’]
tc06-9000b-1t1c-eth-l2xcbase-testpmd-pdrdisc [Cfg] DUT runs L2 frame forwarding config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘50/235/239’, ‘50/274/282’]
LOSS_ACCEPTANCE: 0.5 percentage
tc07-64b-2t2c-eth-l2xcbase-testpmd-ndrdisc [Cfg] DUT runs L2 frame forwarding config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
FINAL_RATE: 25373808.875 pps (2x 12686904.4375 pps)
FINAL_BANDWIDTH: 17.051199564 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘10/30/137’, ‘10/29/42’]
LAT_50%NDR: [‘10/14/35’, ‘10/14/38’]
LAT_10%NDR: [‘10/17/81’, ‘10/17/38’]
tc08-64b-2t2c-eth-l2xcbase-testpmd-pdrdisc [Cfg] DUT runs L2 frame forwarding config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
FINAL_RATE: 25373808.875 pps (2x 12686904.4375 pps)
FINAL_BANDWIDTH: 17.051199564 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘10/28/41’, ‘10/28/42’]
LOSS_ACCEPTANCE: 0.5 percentage
tc09-1518b-2t2c-eth-l2xcbase-testpmd-ndrdisc [Cfg] DUT runs L2 frame forwarding config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/265/273’, ‘20/105/168’]
LAT_50%NDR: [‘10/24/161’, ‘10/26/47’]
LAT_10%NDR: [‘10/22/460’, ‘10/25/433’]
tc10-1518b-2t2c-eth-l2xcbase-testpmd-pdrdisc [Cfg] DUT runs L2 frame forwarding config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/250/292’, ‘20/153/161’]
LOSS_ACCEPTANCE: 0.5 percentage
tc11-9000b-2t2c-eth-l2xcbase-testpmd-ndrdisc [Cfg] DUT runs L2 frame forwarding config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘60/283/286’, ‘50/163/205’]
LAT_50%NDR: [‘50/62/185’, ‘50/64/94’]
LAT_10%NDR: [‘50/61/156’, ‘50/60/133’]
tc12-9000b-2t2c-eth-l2xcbase-testpmd-pdrdisc [Cfg] DUT runs L2 frame forwarding config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘60/251/257’, ‘50/176/221’]
LOSS_ACCEPTANCE: 0.5 percentage
tc13-64b-4t4c-eth-l2xcbase-testpmd-ndrdisc [Cfg] DUT runs L2 frame forwarding config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
FINAL_RATE: 25373808.875 pps (2x 12686904.4375 pps)
FINAL_BANDWIDTH: 17.051199564 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘10/37/42’, ‘10/36/41’]
LAT_50%NDR: [‘10/14/37’, ‘10/14/83’]
LAT_10%NDR: [‘10/17/39’, ‘10/15/36’]
tc14-64b-4t4c-eth-l2xcbase-testpmd-pdrdisc [Cfg] DUT runs L2 frame forwarding config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
FINAL_RATE: 25373808.875 pps (2x 12686904.4375 pps)
FINAL_BANDWIDTH: 17.051199564 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘10/35/44’, ‘10/36/56’]
LOSS_ACCEPTANCE: 0.5 percentage
tc15-1518b-4t4c-eth-l2xcbase-testpmd-ndrdisc [Cfg] DUT runs L2 frame forwarding config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘10/83/102’, ‘20/98/101’]
LAT_50%NDR: [‘10/26/47’, ‘10/24/146’]
LAT_10%NDR: [‘10/24/91’, ‘10/25/170’]
tc16-1518b-4t4c-eth-l2xcbase-testpmd-pdrdisc [Cfg] DUT runs L2 frame forwarding config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/79/96’, ‘20/93/116’]
LOSS_ACCEPTANCE: 0.5 percentage
tc17-9000b-4t4c-eth-l2xcbase-testpmd-ndrdisc [Cfg] DUT runs L2 frame forwarding config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘60/71/88’, ‘50/166/178’]
LAT_50%NDR: [‘50/63/94’, ‘50/66/212’]
LAT_10%NDR: [‘50/61/82’, ‘50/61/81’]
tc18-9000b-4t4c-eth-l2xcbase-testpmd-pdrdisc [Cfg] DUT runs L2 frame forwarding config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘50/104/112’, ‘50/130/138’]
LOSS_ACCEPTANCE: 0.5 percentage

9.3.2. 10ge2p1x520-ethip4-ip4base-l3fwd-ndrpdrdisc

RFC2544: Pkt throughput IPv4 routing test cases

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv4 for L3 IPv4 routing.
  • [Cfg] DUT configuration: DUT1 and DUT2 run the DPDK l3fwd application DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
  • [Ref] Applicable standard specifications: RFC2544.
Name Documentation Status
tc01-64b-1t1c-ethip4-ip4base-l3fwd-ndrdisc [Cfg] DUT runs L3 IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
FINAL_RATE: 7128571.25 pps (2x 3564285.625 pps)
FINAL_BANDWIDTH: 4.79039988 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘10/26/56’, ‘10/25/48’]
LAT_50%NDR: [‘10/31/2074’, ‘10/33/2058’]
LAT_10%NDR: [‘10/88/2122’, ‘10/75/2128’]
tc02-64b-1t1c-ethip4-ip4base-l3fwd-pdrdisc [Cfg] DUT runs L3 IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
FINAL_RATE: 25373808.875 pps (2x 12686904.4375 pps)
FINAL_BANDWIDTH: 17.051199564 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘10/37/53’, ‘10/39/47’]
LOSS_ACCEPTANCE: 0.5 percentage
tc03-1518b-1t1c-ethip4-ip4base-l3fwd-ndrdisc [Cfg] DUT runs L3 IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘50/4398/4406’, ‘80/4347/4356’]
LAT_50%NDR: [‘30/118/2191’, ‘30/113/2222’]
LAT_10%NDR: [‘30/109/2172’, ‘30/132/2203’]
tc04-1518b-1t1c-ethip4-ip4base-l3fwd-pdrdisc [Cfg] DUT runs L3 IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘90/4161/4168’, ‘90/4141/4149’]
LOSS_ACCEPTANCE: 0.5 percentage
tc05-9000b-1t1c-ethip4-ip4base-l3fwd-ndrdisc [Cfg] DUT runs L3 IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘100/4273/4284’, ‘100/4251/4267’]
LAT_50%NDR: [‘60/202/2189’, ‘60/209/2243’]
LAT_10%NDR: [‘60/174/2228’, ‘60/157/2257’]
tc06-9000b-1t1c-ethip4-ip4base-l3fwd-pdrdisc [Cfg] DUT runs L3 IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘90/4235/4245’, ‘70/4181/4192’]
LOSS_ACCEPTANCE: 0.5 percentage
tc07-64b-2t2c-ethip4-ip4base-l3fwd-ndrdisc [Cfg] DUT runs L3 IPv4 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
FINAL_RATE: 6897618.875 pps (2x 3448809.4375 pps)
FINAL_BANDWIDTH: 4.635199884 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘10/23/52’, ‘10/26/81’]
LAT_50%NDR: [‘10/27/100’, ‘10/32/2164’]
LAT_10%NDR: [‘10/52/198’, ‘10/78/2172’]
tc08-64b-2t2c-ethip4-ip4base-l3fwd-pdrdisc [Cfg] DUT runs L3 IPv4 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
FINAL_RATE: 25373808.875 pps (2x 12686904.4375 pps)
FINAL_BANDWIDTH: 17.051199564 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘10/36/56’, ‘10/81/193’]
LOSS_ACCEPTANCE: 0.5 percentage
tc09-1518b-2t2c-ethip4-ip4base-l3fwd-ndrdisc [Cfg] DUT runs L3 IPv4 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘80/162/165’, ‘90/4108/4116’]
LAT_50%NDR: [‘50/109/223’, ‘40/123/2209’]
LAT_10%NDR: [‘40/104/225’, ‘30/130/2120’]
tc10-1518b-2t2c-ethip4-ip4base-l3fwd-pdrdisc [Cfg] DUT runs L3 IPv4 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘90/179/182’, ‘90/4142/4146’]
LOSS_ACCEPTANCE: 0.5 percentage
tc11-9000b-2t2c-ethip4-ip4base-l3fwd-ndrdisc [Cfg] DUT runs L3 IPv4 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘100/331/341’, ‘100/4234/4242’]
LAT_50%NDR: [‘50/198/426’, ‘60/205/2279’]
LAT_10%NDR: [‘60/130/260’, ‘60/149/2212’]
tc12-9000b-2t2c-ethip4-ip4base-l3fwd-pdrdisc [Cfg] DUT runs L3 IPv4 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘70/269/279’, ‘90/4169/4178’]
LOSS_ACCEPTANCE: 0.5 percentage
tc13-64b-4t4c-ethip4-ip4base-l3fwd-ndrdisc [Cfg] DUT runs L3 IPv4 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
FINAL_RATE: 8745237.875 pps (2x 4372618.9375 pps)
FINAL_BANDWIDTH: 5.876799852 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘10/29/64’, ‘10/29/1057’]
LAT_50%NDR: [‘10/33/97’, ‘10/36/275’]
LAT_10%NDR: [‘10/65/276’, ‘10/82/216’]
tc14-64b-4t4c-ethip4-ip4base-l3fwd-pdrdisc [Cfg] DUT runs L3 IPv4 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
FINAL_RATE: 26066666.0 pps (2x 13033333.0 pps)
FINAL_BANDWIDTH: 17.516799552 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/444/447’, ‘20/855/877’]
LOSS_ACCEPTANCE: 0.5 percentage
tc15-1518b-4t4c-ethip4-ip4base-l3fwd-ndrdisc [Cfg] DUT runs L3 IPv4 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘50/192/249’, ‘90/3592/3688’]
LAT_50%NDR: [‘40/119/627’, ‘50/144/606’]
LAT_10%NDR: [‘30/93/217’, ‘30/97/198’]
tc16-1518b-4t4c-ethip4-ip4base-l3fwd-pdrdisc [Cfg] DUT runs L3 IPv4 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘40/210/255’, ‘50/3546/3725’]
LOSS_ACCEPTANCE: 0.5 percentage
tc17-9000b-4t4c-ethip4-ip4base-l3fwd-ndrdisc [Cfg] DUT runs L3 IPv4 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘90/260/305’, ‘60/3333/3477’]
LAT_50%NDR: [‘100/212/395’, ‘100/199/395’]
LAT_10%NDR: [‘50/178/271’, ‘70/127/221’]
tc18-9000b-4t4c-ethip4-ip4base-l3fwd-pdrdisc [Cfg] DUT runs L3 IPv4 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘100/267/326’, ‘100/3393/3509’]
LOSS_ACCEPTANCE: 0.5 percentage

9.3.3. 10ge2p1x710-eth-l2xcbase-testpmd-ndrpdrdisc

RFC2544: Pkt throughput IPv4 routing test cases

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv4 for L2 frame forwarding.
  • [Cfg] DUT configuration: DUT1 and DUT2 run the DPDK testpmd application and use the io forwarding mode. DUT1 and DUT2 tested with 2p10GE NIC X710 Niantic by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
  • [Ref] Applicable standard specifications: RFC2544.
Name Documentation Status
tc01-64b-1t1c-eth-l2xcbase-testpmd-ndrdisc [Cfg] DUT runs L2 frame forwarding config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
FINAL_RATE: 17752380.5 pps (2x 8876190.25 pps)
FINAL_BANDWIDTH: 11.929599696 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘10/16/27’, ‘10/16/28’]
LAT_50%NDR: [‘10/20/150’, ‘10/21/142’]
LAT_10%NDR: [‘10/32/90’, ‘10/28/86’]
tc02-64b-1t1c-eth-l2xcbase-testpmd-pdrdisc [Cfg] DUT runs L2 frame forwarding config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
FINAL_RATE: 29761904.0 pps (2x 14880952.0 pps)
FINAL_BANDWIDTH: 19.999999488 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘10/69/89’, ‘10/72/100’]
LOSS_ACCEPTANCE: 0.5 percentage
tc03-1518b-1t1c-eth-l2xcbase-testpmd-ndrdisc [Cfg] DUT runs L2 frame forwarding config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/150/162’, ‘10/127/169’]
LAT_50%NDR: [‘10/40/155’, ‘10/39/145’]
LAT_10%NDR: [‘20/32/94’, ‘10/35/92’]
tc04-1518b-1t1c-eth-l2xcbase-testpmd-pdrdisc [Cfg] DUT runs L2 frame forwarding config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/200/258’, ‘20/136/173’]
LOSS_ACCEPTANCE: 0.5 percentage
tc05-9000b-1t1c-eth-l2xcbase-testpmd-ndrdisc [Cfg] DUT runs L2 frame forwarding config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘50/189/200’, ‘40/170/197’]
LAT_50%NDR: [‘40/67/176’, ‘40/66/180’]
LAT_10%NDR: [‘40/57/141’, ‘40/57/154’]
tc06-9000b-1t1c-eth-l2xcbase-testpmd-pdrdisc [Cfg] DUT runs L2 frame forwarding config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘50/184/208’, ‘40/159/214’]
LOSS_ACCEPTANCE: 0.5 percentage
tc07-64b-2t2c-eth-l2xcbase-testpmd-ndrdisc [Cfg] DUT runs L2 frame forwarding config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
FINAL_RATE: 16135713.875 pps (2x 8067856.9375 pps)
FINAL_BANDWIDTH: 10.843199724 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘10/16/27’, ‘10/15/25’]
LAT_50%NDR: [‘10/18/86’, ‘10/19/48’]
LAT_10%NDR: [‘10/31/97’, ‘10/31/91’]
tc08-64b-2t2c-eth-l2xcbase-testpmd-pdrdisc [Cfg] DUT runs L2 frame forwarding config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
FINAL_RATE: 29761904.0 pps (2x 14880952.0 pps)
FINAL_BANDWIDTH: 19.999999488 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘10/29/25’, ‘10/28/43’]
LOSS_ACCEPTANCE: 0.5 percentage
tc09-1518b-2t2c-eth-l2xcbase-testpmd-ndrdisc [Cfg] DUT runs L2 frame forwarding config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/93/89’, ‘10/139/160’]
LAT_50%NDR: [‘20/34/180’, ‘10/35/151’]
LAT_10%NDR: [‘20/30/149’, ‘10/31/92’]
tc10-1518b-2t2c-eth-l2xcbase-testpmd-pdrdisc [Cfg] DUT runs L2 frame forwarding config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/45/49’, ‘10/148/164’]
LOSS_ACCEPTANCE: 0.5 percentage
tc11-9000b-2t2c-eth-l2xcbase-testpmd-ndrdisc [Cfg] DUT runs L2 frame forwarding config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘50/180/218’, ‘40/118/115’]
LAT_50%NDR: [‘40/70/128’, ‘40/69/198’]
LAT_10%NDR: [‘40/58/170’, ‘40/57/93’]
tc12-9000b-2t2c-eth-l2xcbase-testpmd-pdrdisc [Cfg] DUT runs L2 frame forwarding config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘50/86/94’, ‘50/174/182’]
LOSS_ACCEPTANCE: 0.5 percentage
tc13-64b-4t4c-eth-l2xcbase-testpmd-ndrdisc [Cfg] DUT runs L2 frame forwarding config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
FINAL_RATE: 29069046.875 pps (2x 14534523.4375 pps)
FINAL_BANDWIDTH: 19.5343995 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘10/18/31’, ‘10/18/30’]
LAT_50%NDR: [‘10/17/45’, ‘10/16/47’]
LAT_10%NDR: [‘10/26/91’, ‘10/28/95’]
tc14-64b-4t4c-eth-l2xcbase-testpmd-pdrdisc [Cfg] DUT runs L2 frame forwarding config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
FINAL_RATE: 29761904.0 pps (2x 14880952.0 pps)
FINAL_BANDWIDTH: 19.999999488 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘10/69/90’, ‘10/24/50’]
LOSS_ACCEPTANCE: 0.5 percentage
tc15-1518b-4t4c-eth-l2xcbase-testpmd-ndrdisc [Cfg] DUT runs L2 frame forwarding config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/56/86’, ‘10/68/80’]
LAT_50%NDR: [‘20/47/158’, ‘10/41/143’]
LAT_10%NDR: [‘20/33/106’, ‘10/38/106’]
tc16-1518b-4t4c-eth-l2xcbase-testpmd-pdrdisc [Cfg] DUT runs L2 frame forwarding config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/61/75’, ‘20/54/75’]
LOSS_ACCEPTANCE: 0.5 percentage
tc17-9000b-4t4c-eth-l2xcbase-testpmd-ndrdisc [Cfg] DUT runs L2 frame forwarding config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘50/109/150’, ‘40/111/144’]
LAT_50%NDR: [‘40/77/201’, ‘40/77/140’]
LAT_10%NDR: [‘40/58/125’, ‘40/56/116’]
tc18-9000b-4t4c-eth-l2xcbase-testpmd-pdrdisc [Cfg] DUT runs L2 frame forwarding config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘50/121/146’, ‘40/108/147’]
LOSS_ACCEPTANCE: 0.5 percentage

9.3.4. 40ge2p1xl710-eth-l2xcbase-testpmd-ndrpdrdisc

RFC2544: Pkt throughput IPv4 routing test cases

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv4 for L2 frame forwarding.
  • [Cfg] DUT configuration: DUT1 and DUT2 run the DPDK testpmd application and use the io forwarding mode. DUT1 and DUT2 tested with 2p40GE NIC XL710 Niantic by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
  • [Ref] Applicable standard specifications: RFC2544.
Name Documentation Status
tc01-64b-1t1c-eth-l2xcbase-testpmd-ndrdisc [Cfg] DUT runs L2 frame forwarding config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 64 Byte frames using binary search start at 40GE linerate, step 100kpps.
FINAL_RATE: 16227343.75 pps (2x 8113671.875 pps)
FINAL_BANDWIDTH: 10.904775 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘10/20/48’, ‘10/16/42’]
LAT_50%NDR: [‘10/18/112’, ‘10/20/96’]
LAT_10%NDR: [‘10/32/99’, ‘10/27/87’]
tc02-64b-1t1c-eth-l2xcbase-testpmd-pdrdisc [Cfg] DUT runs L2 frame forwarding config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 64 Byte frames using binary search start at 40GE linerate, step 100kpps, LT=0.5%.
FINAL_RATE: 37500000.0 pps (2x 18750000.0 pps)
FINAL_BANDWIDTH: 25.2 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘10/40/458’, ‘10/35/322’]
LOSS_ACCEPTANCE: 0.5 percentage
tc03-1518b-1t1c-eth-l2xcbase-testpmd-ndrdisc [Cfg] DUT runs L2 frame forwarding config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 40GE linerate, step 10kpps.
FINAL_RATE: 3765747.84376 pps (2x 1882873.92188 pps)
FINAL_BANDWIDTH: 46.3337614696 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘10/35/62’, ‘10/34/53’]
LAT_50%NDR: [‘10/30/108’, ‘10/31/125’]
LAT_10%NDR: [‘10/32/94’, ‘10/32/94’]
tc04-1518b-1t1c-eth-l2xcbase-testpmd-pdrdisc [Cfg] DUT runs L2 frame forwarding config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 1518 Byte frames using binary search start at 40GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 3982444.0 pps (2x 1991222.0 pps)
FINAL_BANDWIDTH: 48.999990976 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/35/56’, ‘20/35/53’]
LOSS_ACCEPTANCE: 0.5 percentage
tc05-9000b-1t1c-eth-l2xcbase-testpmd-ndrdisc [Cfg] DUT runs L2 frame forwarding config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 9000 Byte frames using binary search start at 40GE linerate, step 10kpps.
FINAL_RATE: 679046.0 pps (2x 339523.0 pps)
FINAL_BANDWIDTH: 48.99995936 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘30/55/88’, ‘30/55/97’]
LAT_50%NDR: [‘20/49/194’, ‘20/48/158’]
LAT_10%NDR: [‘30/46/182’, ‘20/46/153’]
tc06-9000b-1t1c-eth-l2xcbase-testpmd-pdrdisc [Cfg] DUT runs L2 frame forwarding config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 9000 Byte frames using binary search start at 40GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 679046.0 pps (2x 339523.0 pps)
FINAL_BANDWIDTH: 48.99995936 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘30/54/75’, ‘30/56/100’]
LOSS_ACCEPTANCE: 0.5 percentage
tc07-64b-2t2c-eth-l2xcbase-testpmd-ndrdisc [Cfg] DUT runs L2 frame forwarding config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 64 Byte frames using binary search start at 40GE linerate, step 100kpps.
FINAL_RATE: 15644531.25 pps (2x 7822265.625 pps)
FINAL_BANDWIDTH: 10.513125 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘10/16/34’, ‘10/16/39’]
LAT_50%NDR: [‘10/20/115’, ‘10/18/50’]
LAT_10%NDR: [‘10/30/100’, ‘10/33/93’]
tc08-64b-2t2c-eth-l2xcbase-testpmd-pdrdisc [Cfg] DUT runs L2 frame forwarding config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 64 Byte frames using binary search start at 40GE linerate, step 100kpps, LT=0.5%.
FINAL_RATE: 37500000.0 pps (2x 18750000.0 pps)
FINAL_BANDWIDTH: 25.2 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘10/25/63’, ‘10/24/64’]
LOSS_ACCEPTANCE: 0.5 percentage
tc09-1518b-2t2c-eth-l2xcbase-testpmd-ndrdisc [Cfg] DUT runs L2 frame forwarding config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 40GE linerate, step 10kpps.
FINAL_RATE: 3982444.0 pps (2x 1991222.0 pps)
FINAL_BANDWIDTH: 48.999990976 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘10/35/60’, ‘10/33/52’]
LAT_50%NDR: [‘10/31/94’, ‘10/31/152’]
LAT_10%NDR: [‘10/33/148’, ‘10/32/119’]
tc10-1518b-2t2c-eth-l2xcbase-testpmd-pdrdisc [Cfg] DUT runs L2 frame forwarding config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 1518 Byte frames using binary search start at 40GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 3982444.0 pps (2x 1991222.0 pps)
FINAL_BANDWIDTH: 48.999990976 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘10/35/51’, ‘10/34/53’]
LOSS_ACCEPTANCE: 0.5 percentage
tc11-9000b-2t2c-eth-l2xcbase-testpmd-ndrdisc [Cfg] DUT runs L2 frame forwarding config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 9000 Byte frames using binary search start at 40GE linerate, step 10kpps.
FINAL_RATE: 658450.8125 pps (2x 329225.40625 pps)
FINAL_BANDWIDTH: 47.51381063 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘30/56/78’, ‘20/78/125’]
LAT_50%NDR: [‘30/49/110’, ‘20/48/116’]
LAT_10%NDR: [‘20/48/117’, ‘20/50/119’]
tc12-9000b-2t2c-eth-l2xcbase-testpmd-pdrdisc [Cfg] DUT runs L2 frame forwarding config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 9000 Byte frames using binary search start at 40GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 658450.8125 pps (2x 329225.40625 pps)
FINAL_BANDWIDTH: 47.51381063 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/71/152’, ‘20/69/135’]
LOSS_ACCEPTANCE: 0.5 percentage
tc13-64b-4t4c-eth-l2xcbase-testpmd-ndrdisc [Cfg] DUT runs L2 frame forwarding config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find NDR for 64 Byte frames using binary search start at 40GE linerate, step 100kpps.
FINAL_RATE: 32837500.0 pps (2x 16418750.0 pps)
FINAL_BANDWIDTH: 22.0668 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘10/193/115’, ‘10/386/488’]
LAT_50%NDR: [‘10/17/163’, ‘10/16/42’]
LAT_10%NDR: [‘10/24/79’, ‘10/27/79’]
tc14-64b-4t4c-eth-l2xcbase-testpmd-pdrdisc [Cfg] DUT runs L2 frame forwarding config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find PDR for 64 Byte frames using binary search start at 40GE linerate, step 100kpps, LT=0.5%.
FINAL_RATE: 33128906.25 pps (2x 16564453.125 pps)
FINAL_BANDWIDTH: 22.262625 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘10/63/50’, ‘10/34/48’]
LOSS_ACCEPTANCE: 0.5 percentage
tc15-1518b-4t4c-eth-l2xcbase-testpmd-ndrdisc [Cfg] DUT runs L2 frame forwarding config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 40GE linerate, step 10kpps.
FINAL_RATE: 3982444.0 pps (2x 1991222.0 pps)
FINAL_BANDWIDTH: 48.999990976 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘10/37/60’, ‘10/35/79’]
LAT_50%NDR: [‘10/31/92’, ‘10/31/93’]
LAT_10%NDR: [‘10/28/72’, ‘10/30/94’]
tc16-1518b-4t4c-eth-l2xcbase-testpmd-pdrdisc [Cfg] DUT runs L2 frame forwarding config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find PDR for 1518 Byte frames using binary search start at 40GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 3982444.0 pps (2x 1991222.0 pps)
FINAL_BANDWIDTH: 48.999990976 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘10/37/64’, ‘10/36/84’]
LOSS_ACCEPTANCE: 0.5 percentage
tc17-9000b-4t4c-eth-l2xcbase-testpmd-ndrdisc [Cfg] DUT runs L2 frame forwarding config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find NDR for 9000 Byte frames using binary search start at 40GE linerate, step 10kpps.
FINAL_RATE: 679046.0 pps (2x 339523.0 pps)
FINAL_BANDWIDTH: 48.99995936 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘30/61/81’, ‘30/63/99’]
LAT_50%NDR: [‘30/50/124’, ‘20/50/125’]
LAT_10%NDR: [‘20/47/114’, ‘20/43/108’]
tc18-9000b-4t4c-eth-l2xcbase-testpmd-pdrdisc [Cfg] DUT runs L2 frame forwarding config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find PDR for 9000 Byte frames using binary search start at 40GE linerate, step 5kpps, LT=0.5%.
FINAL_RATE: 679046.0 pps (2x 339523.0 pps)
FINAL_BANDWIDTH: 48.99995936 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘30/64/127’, ‘30/62/166’]
LOSS_ACCEPTANCE: 0.5 percentage