7.1.3. IPv6 Routed-Forwarding

7.1.3.1. 10ge2p1x520-ethip6-ip6base-copwhtlistbase-ndrpdrdisc

RFC2544: Pkt throughput IPv6 whitelist test cases

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv6 for IPv6 routing.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv6 routing, two static IPv6 /64 routes and IPv6 COP security whitelist ingress /64 filter entries applied on links TG - DUT1 and DUT2 - TG. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv6 header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
  • [Ref] Applicable standard specifications: RFC2544.
Name Documentation Status
tc01-78B-1t1c-ethip6-ip6base-copwhtlistbase-ndrdisc [Cfg] DUT runs IPv6 routing and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps.
FINAL_RATE: 6923022.9375 pps (2x 3461511.46875 pps)
FINAL_BANDWIDTH: 5.427649983 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘10/99/211’, ‘10/104/192’]
LAT_50%NDR: [‘10/35/95’, ‘10/35/86’]
LAT_10%NDR: [‘10/22/46’, ‘10/20/53’]
tc02-78B-1t1c-ethip6-ip6base-copwhtlistbase-pdrdisc [Cfg] DUT runs IPv6 routing and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
FINAL_RATE: 6923022.9375 pps (2x 3461511.46875 pps)
FINAL_BANDWIDTH: 5.427649983 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘10/97/200’, ‘10/103/229’]
LOSS_ACCEPTANCE: 0.5 percentage
tc03-1518B-1t1c-ethip6-ip6base-copwhtlistbase-ndrdisc [Cfg] DUT runs IPv6 routing and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/237/277’, ‘20/340/382’]
LAT_50%NDR: [‘20/30/165’, ‘20/31/147’]
LAT_10%NDR: [‘20/28/95’, ‘20/28/79’]
tc04-1518B-1t1c-ethip6-ip6base-copwhtlistbase-pdrdisc [Cfg] DUT runs IPv6 routing and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/233/273’, ‘20/385/425’]
LOSS_ACCEPTANCE: 0.5 percentage
tc05-9000B-1t1c-ethip6-ip6base-copwhtlistbase-ndrdisc [Cfg] DUT runs IPv6 routing and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘60/224/279’, ‘60/354/425’]
LAT_50%NDR: [‘50/66/220’, ‘50/66/222’]
LAT_10%NDR: [‘50/62/180’, ‘50/62/157’]
tc06-9000B-1t1c-ethip6-ip6base-copwhtlistbase-pdrdisc [Cfg] DUT runs IPv6 routing and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘60/204/290’, ‘50/327/390’]
LOSS_ACCEPTANCE: 0.5 percentage
tc07-78B-2t2c-ethip6-ip6base-copwhtlistbase-ndrdisc [Cfg] DUT runs IPv6 routing and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps.
FINAL_RATE: 12459630.0625 pps (2x 6229815.03125 pps)
FINAL_BANDWIDTH: 9.768349969 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/58/103’, ‘10/50/158’]
LAT_50%NDR: [‘10/32/63’, ‘10/31/80’]
LAT_10%NDR: [‘10/20/44’, ‘10/21/88’]
tc08-78B-2t2c-ethip6-ip6base-copwhtlistbase-pdrdisc [Cfg] DUT runs IPv6 routing and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
FINAL_RATE: 12459630.0625 pps (2x 6229815.03125 pps)
FINAL_BANDWIDTH: 9.768349969 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/58/104’, ‘20/52/122’]
LOSS_ACCEPTANCE: 0.5 percentage
tc09-1518B-2t2c-ethip6-ip6base-copwhtlistbase-ndrdisc [Cfg] DUT runs IPv6 routing and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/238/274’, ‘20/209/255’]
LAT_50%NDR: [‘20/28/170’, ‘20/26/184’]
LAT_10%NDR: [‘20/25/78’, ‘20/27/75’]
tc10-1518B-2t2c-ethip6-ip6base-copwhtlistbase-pdrdisc [Cfg] DUT runs IPv6 routing and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/288/304’, ‘20/288/307’]
LOSS_ACCEPTANCE: 0.5 percentage
tc11-9000B-2t2c-ethip6-ip6base-copwhtlistbase-ndrdisc [Cfg] DUT runs IPv6 routing and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘50/219/299’, ‘60/197/268’]
LAT_50%NDR: [‘50/65/227’, ‘50/65/277’]
LAT_10%NDR: [‘50/61/134’, ‘50/62/162’]
tc12-9000B-2t2c-ethip6-ip6base-copwhtlistbase-pdrdisc [Cfg] DUT runs IPv6 routing and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘50/232/289’, ‘50/76/116’]
LOSS_ACCEPTANCE: 0.5 percentage

7.1.3.2. 10ge2p1x520-ethip6-ip6base-iacldstbase-ndrpdrdisc

RFC2544: Pkt throughput IPv6 iAcl whitelist test cases

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv6 for IPv6 routing.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv6 routing, two static IPv6 /64 routes and IPv6 iAcl security whitelist ingress /64 filter entries applied on links TG - DUT1 and DUT2 - TG. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv6 header and generated payload. MAC addresses are matching MAC addresses of the TG node interfaces.
  • [Ref] Applicable standard specifications: RFC2544.
Name Documentation Status
tc01-78B-1t1c-ethip6-ip6base-iacldstbase-ndrdisc [Cfg] DUT runs IPv6 routing and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps.
FINAL_RATE: 6923022.9375 pps (2x 3461511.46875 pps)
FINAL_BANDWIDTH: 5.427649983 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘10/184/543’, ‘10/188/556’]
LAT_50%NDR: [‘10/15/69’, ‘10/14/69’]
LAT_10%NDR: [‘10/20/59’, ‘10/19/54’]
tc02-78B-1t1c-ethip6-ip6base-iacldstbase-pdrdisc [Cfg] DUT runs IPv6 routing and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
FINAL_RATE: 6923022.9375 pps (2x 3461511.46875 pps)
FINAL_BANDWIDTH: 5.427649983 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘10/201/835’, ‘20/201/877’]
LOSS_ACCEPTANCE: 0.5 percentage
tc03-1518B-1t1c-ethip6-ip6base-iacldstbase-ndrdisc [Cfg] DUT runs IPv6 routing and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/318/360’, ‘20/408/434’]
LAT_50%NDR: [‘20/15/180’, ‘20/15/183’]
LAT_10%NDR: [‘20/28/154’, ‘20/27/159’]
tc04-1518B-1t1c-ethip6-ip6base-iacldstbase-pdrdisc [Cfg] DUT runs IPv6 routing and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/238/281’, ‘20/372/399’]
LOSS_ACCEPTANCE: 0.5 percentage
tc05-9000B-1t1c-ethip6-ip6base-iacldstbase-ndrdisc [Cfg] DUT runs IPv6 routing and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘60/107/274’, ‘60/158/349’]
LAT_50%NDR: [‘50/66/203’, ‘50/66/210’]
LAT_10%NDR: [‘50/63/156’, ‘50/62/137’]
tc06-9000B-1t1c-ethip6-ip6base-iacldstbase-pdrdisc [Cfg] DUT runs IPv6 routing and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘50/389/448’, ‘60/322/399’]
LOSS_ACCEPTANCE: 0.5 percentage
tc07-78B-2t2c-ethip6-ip6base-iacldstbase-ndrdisc [Cfg] DUT runs IPv6 routing and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps.
FINAL_RATE: 12459630.0625 pps (2x 6229815.03125 pps)
FINAL_BANDWIDTH: 9.768349969 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/95/174’, ‘20/57/175’]
LAT_50%NDR: [‘10/13/59’, ‘10/13/53’]
LAT_10%NDR: [‘10/20/89’, ‘10/21/67’]
tc08-78B-2t2c-ethip6-ip6base-iacldstbase-pdrdisc [Cfg] DUT runs IPv6 routing and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
FINAL_RATE: 12459630.0625 pps (2x 6229815.03125 pps)
FINAL_BANDWIDTH: 9.768349969 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘10/96/194’, ‘10/59/128’]
LOSS_ACCEPTANCE: 0.5 percentage
tc09-1518B-2t2c-ethip6-ip6base-iacldstbase-ndrdisc [Cfg] DUT runs IPv6 routing and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/41/67’, ‘20/398/440’]
LAT_50%NDR: [‘20/29/61’, ‘20/27/192’]
LAT_10%NDR: [‘20/27/562’, ‘20/27/519’]
tc10-1518B-2t2c-ethip6-ip6base-iacldstbase-pdrdisc [Cfg] DUT runs IPv6 routing and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/241/282’, ‘20/225/268’]
LOSS_ACCEPTANCE: 0.5 percentage
tc11-9000B-2t2c-ethip6-ip6base-iacldstbase-ndrdisc [Cfg] DUT runs IPv6 routing and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘60/192/249’, ‘50/250/317’]
LAT_50%NDR: [‘50/63/169’, ‘50/64/139’]
LAT_10%NDR: [‘50/62/122’, ‘50/62/159’]
tc12-9000B-2t2c-ethip6-ip6base-iacldstbase-pdrdisc [Cfg] DUT runs IPv6 routing and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘60/115/292’, ‘50/101/243’]
LOSS_ACCEPTANCE: 0.5 percentage

7.1.3.3. 10ge2p1x520-ethip6-ip6base-ndrpdrdisc

RFC2544: Pkt throughput IPv6 routing test cases

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv6 for IPv6 routing.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv6 routing and two static IPv6 /64 route entries. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv6 header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
  • [Ref] Applicable standard specifications: RFC2544.
Name Documentation Status
tc01-78B-1t1c-ethip6-ip6base-ndrdisc [Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps.
FINAL_RATE: 8109438.75 pps (2x 4054719.375 pps)
FINAL_BANDWIDTH: 6.35779998 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘30/1336/1565’, ‘30/1323/1549’]
LAT_50%NDR: [‘10/21/147’, ‘10/49/191’]
LAT_10%NDR: [‘10/19/34’, ‘10/23/76’]
tc02-78B-1t1c-ethip6-ip6base-pdrdisc [Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
FINAL_RATE: 8109438.75 pps (2x 4054719.375 pps)
FINAL_BANDWIDTH: 6.35779998 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘10/952/2502’, ‘10/659/1390’]
LOSS_ACCEPTANCE: 0.5 percentage
tc03-1518B-1t1c-ethip6-ip6base-ndrdisc [Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/391/433’, ‘20/342/373’]
LAT_50%NDR: [‘20/29/99’, ‘20/29/64’]
LAT_10%NDR: [‘20/25/156’, ‘20/27/136’]
tc04-1518B-1t1c-ethip6-ip6base-pdrdisc [Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/215/242’, ‘20/328/361’]
LOSS_ACCEPTANCE: 0.5 percentage
tc05-9000B-1t1c-ethip6-ip6base-ndrdisc [Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘60/155/383’, ‘50/129/299’]
LAT_50%NDR: [‘50/64/164’, ‘50/65/187’]
LAT_10%NDR: [‘50/61/106’, ‘50/57/79’]
tc06-9000B-1t1c-ethip6-ip6base-pdrdisc [Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘50/95/252’, ‘60/147/351’]
LOSS_ACCEPTANCE: 0.5 percentage
tc07-78B-2t2c-ethip6-ip6base-ndrdisc [Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps.
FINAL_RATE: 16414349.4375 pps (2x 8207174.71875 pps)
FINAL_BANDWIDTH: 12.868849959 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘10/74/166’, ‘10/49/94’]
LAT_50%NDR: [‘10/29/65’, ‘10/21/44’]
LAT_10%NDR: [‘10/9/67’, ‘10/10/76’]
tc08-78B-2t2c-ethip6-ip6base-pdrdisc [Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
FINAL_RATE: 17205293.3125 pps (2x 8602646.65625 pps)
FINAL_BANDWIDTH: 13.488949957 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘10/71/240’, ‘10/61/164’]
LOSS_ACCEPTANCE: 0.5 percentage
tc09-1518B-2t2c-ethip6-ip6base-ndrdisc [Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/202/245’, ‘20/369/407’]
LAT_50%NDR: [‘20/26/63’, ‘20/27/162’]
LAT_10%NDR: [‘20/26/53’, ‘20/25/106’]
tc10-1518B-2t2c-ethip6-ip6base-pdrdisc [Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/240/274’, ‘20/78/116’]
LOSS_ACCEPTANCE: 0.5 percentage
tc11-9000B-2t2c-ethip6-ip6base-ndrdisc [Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘60/116/293’, ‘50/38/128’]
LAT_50%NDR: [‘50/67/229’, ‘50/66/105’]
LAT_10%NDR: [‘50/62/178’, ‘50/62/116’]
tc12-9000B-2t2c-ethip6-ip6base-pdrdisc [Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘60/247/312’, ‘50/196/232’]
LOSS_ACCEPTANCE: 0.5 percentage

7.1.3.4. 10ge2p1x520-ethip6-ip6scale200k-ndrpdrdisc

RFC2544: Pkt throughput IPv6 routing test cases

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv6 for IPv6 routing.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv6 routing and 2x100k static IPv6 /64 route entries. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100k flows per flow-group) with all packets containing Ethernet header, IPv6 header withq IP and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv6 destination address) field is applied to both streams.
  • [Ref] Applicable standard specifications: RFC2544.
Name Documentation Status
tc01-78B-1t1c-ethip6-ip6scale200k-ndrdisc [Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps.
FINAL_RATE: 5341135.1875 pps (2x 2670567.59375 pps)
FINAL_BANDWIDTH: 4.187449987 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘10/445/1134’, ‘20/504/1260’]
LAT_50%NDR: [‘10/42/222’, ‘10/40/269’]
LAT_10%NDR: [‘10/24/138’, ‘10/21/123’]
tc02-78B-1t1c-ethip6-ip6scale200k-pdrdisc [Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
FINAL_RATE: 5341135.1875 pps (2x 2670567.59375 pps)
FINAL_BANDWIDTH: 4.187449987 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘10/518/1217’, ‘10/532/1373’]
LOSS_ACCEPTANCE: 0.5 percentage
tc03-1518B-1t1c-ethip6-ip6scale200k-ndrdisc [Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/545/571’, ‘20/350/377’]
LAT_50%NDR: [‘20/31/296’, ‘20/29/291’]
LAT_10%NDR: [‘20/27/119’, ‘20/26/105’]
tc04-1518B-1t1c-ethip6-ip6scale200k-pdrdisc [Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/496/529’, ‘20/638/660’]
LOSS_ACCEPTANCE: 0.5 percentage
tc05-9000B-1t1c-ethip6-ip6scale200k-ndrdisc [Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘60/346/406’, ‘50/399/448’]
LAT_50%NDR: [‘50/65/248’, ‘50/65/247’]
LAT_10%NDR: [‘50/62/156’, ‘50/62/146’]
tc06-9000B-1t1c-ethip6-ip6scale200k-pdrdisc [Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘60/322/381’, ‘50/387/444’]
LOSS_ACCEPTANCE: 0.5 percentage
tc07-78B-2t2c-ethip6-ip6scale200k-ndrdisc [Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps.
FINAL_RATE: 10877742.3125 pps (2x 5438871.15625 pps)
FINAL_BANDWIDTH: 8.528149973 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘10/282/696’, ‘10/214/563’]
LAT_50%NDR: [‘10/35/112’, ‘10/36/89’]
LAT_10%NDR: [‘10/22/213’, ‘10/20/50’]
tc08-78B-2t2c-ethip6-ip6scale200k-pdrdisc [Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
FINAL_RATE: 10877742.3125 pps (2x 5438871.15625 pps)
FINAL_BANDWIDTH: 8.528149973 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘10/192/500’, ‘10/177/526’]
LOSS_ACCEPTANCE: 0.5 percentage
tc09-1518B-2t2c-ethip6-ip6scale200k-ndrdisc [Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/259/279’, ‘20/301/335’]
LAT_50%NDR: [‘20/28/262’, ‘20/27/258’]
LAT_10%NDR: [‘20/26/226’, ‘20/25/219’]
tc10-1518B-2t2c-ethip6-ip6scale200k-pdrdisc [Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/77/95’, ‘20/485/519’]
LOSS_ACCEPTANCE: 0.5 percentage
tc11-9000B-2t2c-ethip6-ip6scale200k-ndrdisc [Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘50/90/125’, ‘60/369/414’]
LAT_50%NDR: [‘50/33/121’, ‘50/33/195’]
LAT_10%NDR: [‘50/62/177’, ‘50/62/221’]
tc12-9000B-2t2c-ethip6-ip6scale200k-pdrdisc [Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘60/264/352’, ‘50/84/128’]
LOSS_ACCEPTANCE: 0.5 percentage

7.1.3.5. 10ge2p1x520-ethip6-ip6scale20k-ndrpdrdisc

RFC2544: Pkt throughput IPv6 routing test cases

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv6 for IPv6 routing.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv6 routing and 2x10k static IPv6 /64 route entries. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv6 header withq IP and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv6 destination address) field is applied to both streams.
  • [Ref] Applicable standard specifications: RFC2544.
Name Documentation Status
tc01-78B-1t1c-ethip6-ip6scale20k-ndrdisc [Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps.
FINAL_RATE: 6923022.9375 pps (2x 3461511.46875 pps)
FINAL_BANDWIDTH: 5.427649983 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘10/67/188’, ‘20/68/192’]
LAT_50%NDR: [‘10/28/220’, ‘10/32/218’]
LAT_10%NDR: [‘10/23/53’, ‘10/19/46’]
tc02-78B-1t1c-ethip6-ip6scale20k-pdrdisc [Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
FINAL_RATE: 6923022.9375 pps (2x 3461511.46875 pps)
FINAL_BANDWIDTH: 5.427649983 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘10/67/199’, ‘10/68/159’]
LOSS_ACCEPTANCE: 0.5 percentage
tc03-1518B-1t1c-ethip6-ip6scale20k-ndrdisc [Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/255/310’, ‘20/372/414’]
LAT_50%NDR: [‘20/28/205’, ‘20/30/200’]
LAT_10%NDR: [‘20/26/166’, ‘20/25/147’]
tc04-1518B-1t1c-ethip6-ip6scale20k-pdrdisc [Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/246/567’, ‘20/333/543’]
LOSS_ACCEPTANCE: 0.5 percentage
tc05-9000B-1t1c-ethip6-ip6scale20k-ndrdisc [Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘50/199/265’, ‘50/325/379’]
LAT_50%NDR: [‘50/65/192’, ‘50/66/182’]
LAT_10%NDR: [‘50/61/101’, ‘50/62/99’]
tc06-9000B-1t1c-ethip6-ip6scale20k-pdrdisc [Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘50/202/261’, ‘60/341/406’]
LOSS_ACCEPTANCE: 0.5 percentage
tc07-78B-2t2c-ethip6-ip6scale20k-ndrdisc [Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps.
FINAL_RATE: 14436989.75 pps (2x 7218494.875 pps)
FINAL_BANDWIDTH: 11.318599964 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘10/777/870’, ‘20/96/135’]
LAT_50%NDR: [‘10/31/61’, ‘10/30/61’]
LAT_10%NDR: [‘10/22/75’, ‘10/20/48’]
tc08-78B-2t2c-ethip6-ip6scale20k-pdrdisc [Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
FINAL_RATE: 14832461.6875 pps (2x 7416230.84375 pps)
FINAL_BANDWIDTH: 11.628649963 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘40/754/846’, ‘10/99/129’]
LOSS_ACCEPTANCE: 0.5 percentage
tc09-1518B-2t2c-ethip6-ip6scale20k-ndrdisc [Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/244/281’, ‘20/185/230’]
LAT_50%NDR: [‘20/26/79’, ‘20/29/127’]
LAT_10%NDR: [‘20/27/119’, ‘20/27/79’]
tc10-1518B-2t2c-ethip6-ip6scale20k-pdrdisc [Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/220/265’, ‘20/55/78’]
LOSS_ACCEPTANCE: 0.5 percentage
tc11-9000B-2t2c-ethip6-ip6scale20k-ndrdisc [Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘60/219/308’, ‘50/191/245’]
LAT_50%NDR: [‘50/66/237’, ‘50/66/117’]
LAT_10%NDR: [‘50/61/171’, ‘50/56/91’]
tc12-9000B-2t2c-ethip6-ip6scale20k-pdrdisc [Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘60/82/132’, ‘50/337/414’]
LOSS_ACCEPTANCE: 0.5 percentage

7.1.3.6. 10ge2p1x520-ethip6-ip6scale2m-ndrpdrdisc

RFC2544: Pkt throughput IPv6 routing test cases

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv6 for IPv6 routing.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv6 routing and 2x1M static IPv6 /64 route entries. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 1M flows per flow-group) with all packets containing Ethernet header, IPv6 header withq IP and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv6 destination address) field is applied to both streams.
  • [Ref] Applicable standard specifications: RFC2544.
Name Documentation Status
tc01-78B-1t1c-ethip6-ip6scale2m-ndrdisc [Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps.
FINAL_RATE: 4550191.3125 pps (2x 2275095.65625 pps)
FINAL_BANDWIDTH: 3.567349989 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘10/221/1221’, ‘10/231/1222’]
LAT_50%NDR: [‘10/42/119’, ‘10/42/122’]
LAT_10%NDR: [‘10/10/90’, ‘10/13/112’]
tc02-78B-1t1c-ethip6-ip6scale2m-pdrdisc [Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
FINAL_RATE: 4550191.3125 pps (2x 2275095.65625 pps)
FINAL_BANDWIDTH: 3.567349989 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘10/346/1372’, ‘10/332/1397’]
LOSS_ACCEPTANCE: 0.5 percentage
tc03-1518B-1t1c-ethip6-ip6scale2m-ndrdisc [Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/386/409’, ‘20/505/538’]
LAT_50%NDR: [‘20/29/333’, ‘20/31/331’]
LAT_10%NDR: [‘20/27/141’, ‘20/26/227’]
tc04-1518B-1t1c-ethip6-ip6scale2m-pdrdisc [Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/326/350’, ‘20/497/531’]
LOSS_ACCEPTANCE: 0.5 percentage
tc05-9000B-1t1c-ethip6-ip6scale2m-ndrdisc [Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘60/196/252’, ‘50/337/416’]
LAT_50%NDR: [‘50/66/169’, ‘50/66/166’]
LAT_10%NDR: [‘50/62/247’, ‘50/62/227’]
tc06-9000B-1t1c-ethip6-ip6scale2m-pdrdisc [Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘50/234/272’, ‘50/384/430’]
LOSS_ACCEPTANCE: 0.5 percentage
tc07-78B-2t2c-ethip6-ip6scale2m-ndrdisc [Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps.
Socket timeout: ip_add_del_route 2001:2::0/128 via 2001:5::2 sw_if_index 1 resolve-attempts 10 count 1000000
tc08-78B-2t2c-ethip6-ip6scale2m-pdrdisc [Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
Socket timeout: ip_add_del_route 2001:1::0/128 via 2001:3::2 sw_if_index 2 resolve-attempts 10 count 1000000
tc09-1518B-2t2c-ethip6-ip6scale2m-ndrdisc [Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
Socket timeout: ip_add_del_route 2001:1::0/128 via 2001:3::2 sw_if_index 2 resolve-attempts 10 count 1000000
tc10-1518B-2t2c-ethip6-ip6scale2m-pdrdisc [Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
Socket timeout: ip_add_del_route 2001:2::0/128 via 2001:5::2 sw_if_index 1 resolve-attempts 10 count 1000000
tc11-9000B-2t2c-ethip6-ip6scale2m-ndrdisc [Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
Socket timeout: ip_add_del_route 2001:1::0/128 via 2001:3::2 sw_if_index 2 resolve-attempts 10 count 1000000
tc12-9000B-2t2c-ethip6-ip6scale2m-pdrdisc [Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
Socket timeout: ip_add_del_route 2001:1::0/128 via 2001:3::2 sw_if_index 2 resolve-attempts 10 count 1000000

7.1.3.7. 40ge2p1xl710-ethip6-ip6base-ndrpdrdisc

RFC2544: Pkt throughput IPv6 routing test cases

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv6 for IPv6 routing.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv6 routing and two static IPv6 /64 route entries. DUT1 and DUT2 tested with 2p40GE NIC XL710 by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv6 header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
  • [Ref] Applicable standard specifications: RFC2544.
Name Documentation Status
tc01-78B-1t1c-ethip6-ip6base-ndrdisc [Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 78 Byte frames using binary search start at 18.75Mpps rate, step 100kpps.
FINAL_RATE: 8067968.75 pps (2x 4033984.375 pps)
FINAL_BANDWIDTH: 6.3252875 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/60/179’, ‘20/59/172’]
LAT_50%NDR: [‘10/10/150’, ‘20/20/161’]
LAT_10%NDR: [‘10/21/68’, ‘10/23/58’]
tc03-1518B-1t1c-ethip6-ip6base-ndrdisc [Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 24.5G rate, step 10kpps.
FINAL_RATE: 3982444.0 pps (2x 1991222.0 pps)
FINAL_BANDWIDTH: 48.999990976 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘10/36/225’, ‘10/35/232’]
LAT_50%NDR: [‘10/29/118’, ‘10/27/107’]
LAT_10%NDR: [‘10/22/143’, ‘10/22/123’]
tc07-78B-2t2c-ethip6-ip6base-ndrdisc [Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 78 Byte frames using binary search start at 18.75Mpps rate, step 100kpps.
FINAL_RATE: 15644531.25 pps (2x 7822265.625 pps)
FINAL_BANDWIDTH: 12.2653125 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘10/41/456’, ‘10/40/466’]
LAT_50%NDR: [‘10/11/85’, ‘10/11/187’]
LAT_10%NDR: [‘10/21/58’, ‘10/20/44’]
tc09-1518B-2t2c-ethip6-ip6base-ndrdisc [Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 24.5G rate, step 10kpps.
FINAL_RATE: 3982444.0 pps (2x 1991222.0 pps)
FINAL_BANDWIDTH: 48.999990976 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘10/34/221’, ‘10/34/97’]
LAT_50%NDR: [‘10/28/157’, ‘10/26/112’]
LAT_10%NDR: [‘10/21/48’, ‘10/21/90’]