7.3.10. LISP Overlay Tunnels¶
7.3.10.1. api-crud-lisp-func¶
API test cases
- [Top] Network Topologies: DUT1 1-node topology.
- [Enc] Packet Encapsulations: None.
- [Cfg] DUT configuration: DUT1 gets configured with all LISP parameters.
- [Ver] Verification: DUT1 operational data gets verified following configuration.
- [Ref] Applicable standard specifications: RFC6830.
| Name | Documentation | Status |
|---|---|---|
| TC01: DUT can enable and disable LISP | [Top] DUT1. [Enc] None. [Cfg1] Test LISP enable/disable API; On DUT1 enable LISP. [Ver1] Check DUT1 if LISP is enabled. [Cfg2] Then disable LISP. [Ver2] Check DUT1 if LISP is disabled. [Ref] RFC6830. |
PASS |
| TC02: DUT can add and delete locator_set | [Top] DUT1. [Enc] None. [Cfg1] Test LISP locator_set API; on DUT1 configure locator_set and locator. [Ver1] Check DUT1 configured locator_set and locator are correct. [Cfg2] Then remove locator_set and locator. [Ver2] check DUT1 locator_set and locator are removed. [Ref] RFC6830. |
PASS |
| TC03: DUT can add, reset and delete locator_set | [Top] DUT1. [Enc] None. [Cfg1] Test LISP locator_set API; on DUT1 configure locator_set and locator. [Ver1] Check DUT1 locator_set and locator are correct. [Cfg2] Then reset locator_set and set it again. [Ver2] Check DUT1 locator_set and locator are correct. [Cfg3] Then remove locator_set and locator. [Ver3] Check DUT1 all locator_set and locators are removed. [Ref] RFC6830. |
PASS |
| TC04: DUT can add and delete eid address | [Top] DUT1. [Enc] None. [Cfg1] Test LISP eid API; on DUT1 configure LISP eid IP address. [Ver1] Check DUT1 configured data is correct. [Cfg2] Remove configured data. [Ver2] Check DUT1 all eid IP addresses are removed. [Ref] RFC6830. |
PASS |
| TC05: DUT can add and delete LISP map resolver address | [Top] DUT1. [Enc] None. [Cfg1] Test LISP map resolver address API; on DUT1 configure LISP map resolver address. [Ver1] Check DUT1 configured data is correct. [Cfg2] Remove configured data. [Ver2] Check DUT1 all map resolver addresses are removed. [Ref] RFC6830. |
PASS |
7.3.10.2. eth2p-ethip4ipsectptlispgpe-ip4base-eth-2vhost-1vm-func¶
IPv4-ip4-ipsec-lispgpe-ip4 - main fib, vrf (gpe_vni-to-vrf)
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: ICMPv4-IPv4-IPSec-LISPGPE-IPv4-ICMPv4.
- [Cfg] DUT configuration: Each DUT is configured with LISP and IPsec. IPsec is in transport mode. Tests cases are for IPsec configured both on RLOC interface or lisp_gpe0 interface.
- [Ver] TG verification: Packet is send from TG(if1) across the DUT1 via VM to DUT2 where it is forwarded to TG(if2).
- [Ref] Applicable standard specifications: RFC6830, RFC4303.
| Name | Documentation | Status |
|---|---|---|
| TC01: DUT1 and DUT2 route IPv4 over Vhost to LISP GPE tunnel using IPsec (transport) on RLOC Int. | [Top] TG-DUT1-DUT2-TG. [Enc] Eth-IPv4-IPSec-LISPGPE-IPv4-ICMP on DUT1-DUT2, Eth-IPv4-ICMP on TG-DUTn. [Cfg] Configure IPv4 LISP static adjacencies on DUT1 and DUT2 with IPsec in between DUTS. Create Qemu vm on DUT1 and configure bridge between two vhosts. [Ver] Case: ip4-ipsec-lispgpe-ip4 - main fib, virt2lisp Make TG send ICMPv4 Echo Req between its interfaces across both DUTs and LISP GPE tunnel between them; verify IPv4 headers on received packets are correct. [Ref] RFC6830, RFC4303. |
PASS |
| TC02: DUT1 and DUT2 route IPv4 over Vhost to LISP GPE tunnel using IPsec (transport) on lisp_gpe0 Int. | [Top] TG-DUT1-DUT2-TG. [Enc] Eth-IPv4-IPSec-LISPGPE-IPv4-ICMPv4 on DUT1-DUT2, Eth-IPv4-ICMPv4 on TG-DUTn. [Cfg] Configure IPv4 LISP static adjacencies on DUT1 and DUT2 with IPsec in between DUTS. [Ver] Case: ip4-ipsec-lispgpe-ip4 - main fib, virt2lisp Make TG send ICMPv4 Echo Req between its interfaces across both DUTs and LISP GPE tunnel between them; verify IPv4 headers on received packets are correct. [Ref] RFC6830, RFC4303. |
PASS |
7.3.10.3. eth2p-ethip4ipsectptlispgpe-ip4base-func¶
IPv4-ip4-ipsec-lispgpe-ip4 - main fib, vrf (gpe_vni-to-vrf)
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: ICMPv4-IPv4-IPSec-LISPGPE-IPv4-ICMPv4.
- [Cfg] DUT configuration: Each DUT is configured with LISP and IPsec. IPsec is in transport mode. Tests cases are for IPsec configured both on RLOC interface or lisp_gpe0 interface.
- [Ver] TG verification: Packet is send from TG(if1) across the DUT1 to DUT2 where it is forwarded to TG(if2).
- [Ref] Applicable standard specifications: RFC6830, RFC4303.
| Name | Documentation | Status |
|---|---|---|
| TC01: DUT1 and DUT2 route IPv4 bidirectionally over LISP GPE tunnel using IPsec (transport) on RLOC Int. | [Top] TG-DUT1-DUT2-TG. [Enc] Eth-IPv4-IPSec-LISPGPE-IPv4-ICMPv4 on DUT1-DUT2, Eth-IPv4-ICMPv4 on TG-DUTn. [Cfg] Configure IPv4 LISP static adjacencies on DUT1 and DUT2 with IPsec in between DUTs. [Ver] Case: ip4-lispgpe-ipsec-ip4 - main fib Make TG send ICMPv4 Echo Req between its interfaces across both DUTs and LISP GPE tunnel between them; verify IPv4 headers on received packets are correct. [Ref] RFC6830, RFC4303. |
PASS |
| TC02: DUT1 and DUT2 route IPv4 bidirectionally over LISP GPE tunnel using IPsec (transport) lisp_gpe0 Int. | [Top] TG-DUT1-DUT2-TG. [Enc] Eth-IPv4-IPSec-LISPGPE-IPv4-ICMPv4 on DUT1-DUT2, Eth-IPv4-ICMPv4 on TG-DUTn. [Cfg] Configure IPv4 LISP static adjacencies on DUT1 and DUT2 with IPsec in between DUTs. [Ver] Case: ip4-ipsec-lispgpe-ip4 - main fib Make TG send ICMPv4 Echo Req between its interfaces across both DUTs and LISP GPE tunnel between them; verify IPv4 headers on received packets are correct. [Ref] RFC6830, RFC4303. |
PASS |
| TC03: DUT1 and DUT2 route IPv4 bidirectionally over LISP GPE tunnel using IPsec (transport) on RLOC Int and VRF on EID is enabled. | [Top] TG-DUT1-DUT2-TG. [Enc] Eth-IPv4-IPSec-LISPGPE-IPv4-ICMPv4 on DUT1-DUT2, Eth-IPv4-ICMPv4 on TG-DUTn. [Cfg] Configure IPv4 LISP static adjacencies on DUT1 and DUT2 with IPsec in between DUTs. [Ver] Case: ip4-lispgpe-ipsec-ip4 - vrf, main fib Make TG send ICMPv4 Echo Req between its interfaces across both DUTs and LISP GPE tunnel between them; verify IPv4 headers on received packets are correct. [Ref] RFC6830, RFC4303. |
PASS |
| TC04: DUT1 and DUT2 route IPv4 bidirectionally over LISP GPE tunnel using IPsec (transport) on lisp_gpe0 Int and VRF is enabled. | [Top] TG-DUT1-DUT2-TG. [Enc] Eth-IPv4-IPSec-LISPGPE-IPv4-ICMPv4 on DUT1-DUT2, Eth-IPv4-ICMPv4 on TG-DUTn. [Cfg] Configure IPv4 LISP static adjacencies on DUT1 and DUT2 with IPsec in between DUTs. [Ver] Case: ip4-ipsec-lispgpe-ip4 - vrf, main fib Make TG send ICMPv4 Echo Req between its interfaces across both DUTs and LISP GPE tunnel between them; verify IPv4 headers on received packets are correct. [Ref] RFC6830, RFC4303. |
PASS |
7.3.10.4. eth2p-ethip4ipsectptlispgpe-ip6base-eth-2vhost-1vm-func¶
IPv6 - ip4-ipsec-lispgpe-ip6 - main fib, vrf, virt2lisp, phy2lisp
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv4-LISPGPE-IPSec-IPv6-ICMP, Eth-IPv4-IPSec-LISPGPE-IPv6-ICMP
- [Cfg] DUT configuration: Each DUT is configured with LISP and IPsec. IPsec is in transport mode. Tests cases are for IPsec configured both on RLOC interface or lisp_gpe0 interface.
- [Ver] TG verification: Packet is send from TG(if1) across the DUT1 via VM to DUT2 where it is forwarded to TG(if2).
- [Ref] Applicable standard specifications: RFC6830, RFC4303.
| Name | Documentation | Status |
|---|---|---|
| TC01: DUT1 and DUT2 route IPv6 over Vhost to LISP GPE tunnel using IPsec (transport) on RLOC Int. | [Top] TG-DUT1-DUT2-TG. [Enc] Eth-IPv4-LISPGPE-IPSec-IPv6-ICMP on DUT1-DUT2, Eth-IPv6-ICMP on TG-DUTn. [Cfg] Configure IPv4 LISP static adjacencies on DUT1 and DUT2 with IPsec in between DUTS. Create Qemu vm on DUT1 and configure bridge between two vhosts. [Ver] Case: ip4-ipsec-lispgpe-ip6 - main fib, virt2lisp Make TG send ICMPv6 Echo Req between its interfaces across both DUTs and LISP GPE tunnel between them; verify IPv6 headers on received packets are correct. [Ref] RFC6830, RFC4303. |
PASS |
| TC02: DUT1 and DUT2 route IPv6 over Vhost to LISP GPE tunnel using IPsec (transport) on lisp_gpe0 Int. | [Top] TG-DUT1-DUT2-TG. [Enc] Eth-IPv4-IPSec-LISPGPE-IPv6-ICMPv6 on DUT1-DUT2, Eth-IPv6-ICMPv6, on TG-DUTn. [Cfg] Configure IPv4 LISP static adjacencies on DUT1 and DUT2 with IPsec in between DUTS. [Ver] Case: ip4-ipsec-lispgpe-ip6 - main fib, virt2lisp Make TG send ICMPv6 Echo Req between its interfaces across both DUTs and LISP GPE tunnel between them; verify IPv6 headers on received packets are correct. [Ref] RFC6830, RFC4303. |
PASS |
7.3.10.5. eth2p-ethip4ipsectptlispgpe-ip6base-func¶
IPv6 - ip4-ipsec-lispgpe-ip6 - main fib, vrf, virt2lisp, phy2lisp
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv4-LISPGPE-IPSec-IPv6-ICMP, Eth-IPv4-IPSec-LISPGPE-IPv6-ICMP
- [Cfg] DUT configuration: Each DUT is configured with LISP and IPsec. IPsec is in transport mode. Tests cases are for IPsec configured both on RLOC interface or lisp_gpe0 interface.
- [Ver] TG verification: Packet is send from TG(if1) across the DUT1 to DUT2 where it is forwarded to TG(if2).
- [Ref] Applicable standard specifications: RFC6830, RFC4303.
| Name | Documentation | Status |
|---|---|---|
| TC01: DUT1 and DUT2 route IPv4 bidirectionally over LISP GPE tunnel using IPsec (transport) on RLOC Int. | [Top] TG-DUT1-DUT2-TG. [Enc] Eth-IPv4-LISPGPE-IPSec-IPv6-ICMP on DUT1-DUT2, Eth-IPv6-ICMP on TG-DUTn. [Cfg] Configure IPv6 LISP static adjacencies on DUT1 and DUT2 with IPsec in between DUTS. [Ver] Make TG send ICMPv6 Echo Req between its interfaces across both DUTs and LISP GPE tunnel between them; verify IPv6 headers on received packets are correct. [Ref] RFC6830, RFC4303. |
PASS |
| TC02: DUT1 and DUT2 route IPv4 bidirectionally over LISP GPE tunnel using IPsec (transport) on lisp_gpe0 Int. | [Top] TG-DUT1-DUT2-TG. [Enc] Eth-IPv4-IPSec-LISPGPE-IPv6-ICMPv6 on DUT1-DUT2, Eth-IPv6-ICMP on TG-DUTn. [Cfg] Configure IPv4 LISP static adjacencies on DUT1 and DUT2 with IPsec in between DUTS. [Ver] Make TG send ICMPv6 Echo Req between its interfaces across both DUTs and LISP GPE tunnel between them; verify IPv6 headers on received packets are correct. [Ref] RFC6830, RFC4303. |
PASS |
7.3.10.6. eth2p-ethip4ipsectptlispgpe-ip6basevrf-func¶
IPv6 - ip4-ipsec-lispgpe-ip6 - main fib, vrf, virt2lisp, phy2lisp
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv4-LISPGPE-IPSec-IPv6-ICMP, Eth-IPv4-IPSec-LISPGPE-IPv6-ICMP
- [Cfg] DUT configuration: Each DUT is configured with LISP and IPsec. IPsec is in transport mode. Tests cases are for IPsec configured both on RLOC interface or lisp_gpe0 interface.
- [Ver] TG verification: Packet is send from TG(if1) across the DUT1 to DUT2 where it is forwarded to TG(if2).
- [Ref] Applicable standard specifications: RFC6830, RFC4303.
| Name | Documentation | Status |
|---|---|---|
| TC01: DUT1 and DUT2 route IPv6 bidirectionally over LISP GPE tunnel using physical interfaces and VRF is enabled | [Top] TG-DUT1-DUT2-TG. [Enc] Eth-IPv4-IPSec-LISPGPE-IPv6-ICMPv6 on DUT1-DUT2, Eth-IPv6-ICMPv6, on TG-DUTn. [Cfg] Configure IPv4 LISP static adjacencies on DUT1 and DUT2 with IPsec in between DUTS. [Ver] Case: ip4-ipsec-lispgpe-ip6 - vrf, phy2lisp Make TG send ICMPv6 Echo Req between its interfaces across both DUTs and LISP GPE tunnel between them; verify IPv6 headers on received packets are correct. [Ref] RFC6830, RFC4303. |
PASS |
7.3.10.7. eth2p-ethip4lisp-ip4base-func¶
IP AFI independent functional tests.
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv4-LISP-IPv4-ICMPv4 on DUT1-DUT2, Eth-IPv4-ICMPv4 on TG-DUTn for IPv4 routing over LISPoIPv4 tunnel.
- [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv4 routing and static routes. LISPoIPv4 tunnel is configured between DUT1 and DUT2.
- [Ver] TG verification: Test ICMPv4 Echo Request packets are sent in both directions by TG on links to DUT1 and DUT2; on receive TG verifies packets for correctness and their IPv4 src-addr, dst-addr and MAC addresses.
- [Ref] Applicable standard specifications: RFC6830.
| Name | Documentation | Status |
|---|---|---|
| TC01: DUT1 and DUT2 route IPv4 over LISPoIPv4 tunnel after disable-enable | [Top] TG-DUT1-DUT2-TG. [Enc] Eth-IPv4-LISP-IPv4-ICMPv4 on DUT1-DUT2, Eth-IPv4-ICMPv4 on TG-DUTn. [Cfg1] On DUT1 and DUT2 configure IPv4 LISP static adjacencies. [Ver1] Make TG send ICMPv4 Echo Req between its interfaces across both DUTs and LISP tunnel between them; verify IPv4 headers on received packets are correct. [Cfg2] Disable LISP. [Ver2] Verify packets are not received via LISP tunnel. [Cfg3] Re-enable LISP. [Ver3] Verify packets are received again via LISP tunnel. [Ref] RFC6830. |
PASS |
7.3.10.8. eth2p-ethip4lisp-l2bdbasemaclrn-func¶
ip4-lispgpe-ip4 encapsulation test cases
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv4-ICMPv4-LISPGpe-IP4
- [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv4 routing and static routes. LISPoIPv4 tunnel is configured between DUT1 and DUT2.
- [Ver] TG verification: Test ICMPv4 Echo Request packets are sent in both directions by TG on links to DUT1 and DUT2; on receive TG verifies packets for correctness and their IPv4 src-addr, dst-addr and MAC addresses.
- [Ref] Applicable standard specifications: RFC6830.
| Name | Documentation | Status |
|---|---|---|
| TC01: Route IPv4 packet through LISP with Bridge Domain setup. | [Top] TG-DUT1-DUT2-TG. [Enc] Eth-IPv4-ICMPv4-LISPGpe-IP4 [Cfg] Configure IPv4 LISP static adjacencies on DUT1 and DUT2. Also configure BD and assign it to LISP VNI. [Ver] Make TG send ICMPv4 Echo Req between its interfaces across both DUTs and LISP tunnel between them; verify IPv4, Ether headers on received packets are correct. [Ref] RFC6830. |
PASS |
7.3.10.9. eth2p-ethip4lispgpe-ip4base-eth-2vhost-1vm-func¶
ip4-lispgpe-ip4 encapsulation test cases
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv4-LISP-IPv4-ICMPv4 on DUT1-DUT2, Eth-IPv4-ICMPv4 on TG-DUTn for IPv4 routing over LISPoIPv4 tunnel.
- [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv4 routing and static routes. LISPoIPv4 tunnel is configured between DUT1 and DUT2.
- [Ver] TG verification: Test ICMPv4 Echo Request packets are sent in both directions by TG on links to DUT1 and DUT2; on receive TG verifies packets for correctness and their IPv4 src-addr, dst-addr and MAC addresses.
- [Ref] Applicable standard specifications: RFC6830.
| Name | Documentation | Status |
|---|---|---|
| TC01: DUT1 and DUT2 route IPv4 bidirectionally over LISP GPE tunnel using vhost interfaces | [Top] TG-DUT1-DUT2-TG. [Enc] Eth-IPv4-LISPGPE-IPv4-ICMPv4 on DUT1-DUT2, Eth-IPv4-ICMPv4 on TG-DUTn. [Cfg] Configure IPv4 LISP static adjacencies on DUT1 and DUT2. [Ver] Case: ip4-lispgpe-ip4 - main fib, virt2lisp Make TG send ICMPv4 Echo Req between its interfaces across both DUTs and LISP GPE tunnel between them; verify IPv4 headers on received packets are correct. |
PASS |
7.3.10.10. eth2p-ethip4lispgpe-ip4base-func¶
ip4-lispgpe-ip4 encapsulation test cases
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv4-LISP-IPv4-ICMPv4 on DUT1-DUT2, Eth-IPv4-ICMPv4 on TG-DUTn for IPv4 routing over LISPoIPv4 tunnel.
- [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv4 routing and static routes. LISPoIPv4 tunnel is configured between DUT1 and DUT2.
- [Ver] TG verification: Test ICMPv4 Echo Request packets are sent in both directions by TG on links to DUT1 and DUT2; on receive TG verifies packets for correctness and their IPv4 src-addr, dst-addr and MAC addresses.
- [Ref] Applicable standard specifications: RFC6830.
| Name | Documentation | Status |
|---|---|---|
| TC01: DUT1 and DUT2 route IPv4 bidirectionally over LISP GPE tunnel using physical interfaces | [Top] TG-DUT1-DUT2-TG. [Enc] Eth-IPv4-LISPGPE-IPv4-ICMPv4 on DUT1-DUT2, Eth-IPv4-ICMPv4 on TG-DUTn. [Cfg] Configure IPv4 LISP static adjacencies on DUT1 and DUT2. [Ver] Case: ip4-lispgpe-ip4 - phy2lisp Make TG send ICMPv4 Echo Req between its interfaces across both DUTs and LISP GPE tunnel between them; verify IPv4 headers on received packets are correct. [Ref] RFC6830. |
PASS |
7.3.10.11. eth2p-ethip4lispgpe-ip4basevrf-eth-2vhost-1vm-func¶
ip4-lispgpe-ip4 encapsulation test cases
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv4-LISP-IPv4-ICMPv4 on DUT1-DUT2, Eth-IPv4-ICMPv4 on TG-DUTn for IPv4 routing over LISPoIPv4 tunnel.
- [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv4 routing and static routes. LISPoIPv4 tunnel is configured between DUT1 and DUT2.
- [Ver] TG verification: Test ICMPv4 Echo Request packets are sent in both directions by TG on links to DUT1 and DUT2; on receive TG verifies packets for correctness and their IPv4 src-addr, dst-addr and MAC addresses.
- [Ref] Applicable standard specifications: RFC6830.
| Name | Documentation | Status |
|---|---|---|
| TC01: DUT1 and DUT2 route IPv4 bidirectionally over LISP GPE tunnel using vhost interfaces and VRF is enabled | [Top] TG-DUT1-DUT2-TG. [Enc] Eth-IPv4-LISPGPE-IPv4-ICMPv4 on DUT1-DUT2, Eth-IPv4-ICMPv4 on TG-DUTn. [Cfg] Configure IPv4 LISP static adjacencies on DUT1 and DUT2. [Ver] Case: ip4-lispgpe-ip4 - vrf, virt2lisp Make TG send ICMPv4 Echo Req between its interfaces across both DUTs and LISP GPE tunnel between them; verify IPv4 headers on received packets are correct. [Ref] RFC6830. |
PASS |
7.3.10.12. eth2p-ethip4lispgpe-ip4basevrf-func¶
ip4-lispgpe-ip4 encapsulation test cases
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv4-LISP-IPv4-ICMPv4 on DUT1-DUT2, Eth-IPv4-ICMPv4 on TG-DUTn for IPv4 routing over LISPoIPv4 tunnel.
- [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv4 routing and static routes. LISPoIPv4 tunnel is configured between DUT1 and DUT2.
- [Ver] TG verification: Test ICMPv4 Echo Request packets are sent in both directions by TG on links to DUT1 and DUT2; on receive TG verifies packets for correctness and their IPv4 src-addr, dst-addr and MAC addresses.
- [Ref] Applicable standard specifications: RFC6830.
| Name | Documentation | Status |
|---|---|---|
| TC01: DUT1 and DUT2 route IPv4 bidirectionally over LISP GPE tunnel using physical interfaces and VRF is enabled | [Top] TG-DUT1-DUT2-TG. [Enc] Eth-IPv4-LISPGPE-IPv4-ICMPv4 on DUT1-DUT2, Eth-IPv4-ICMPv4 on TG-DUTn. [Cfg] Configure IPv4 LISP static adjacencies on DUT1 and DUT2. [Ver] Case: ip4-lispgpe-ip4 - vrf, phy2lisp Make TG send ICMPv4 Echo Req between its interfaces across both DUTs and LISP GPE tunnel between them; verify IPv4 headers on received packets are correct. [Ref] RFC6830. |
PASS |
7.3.10.13. eth2p-ethip4lispgpe-ip6base-eth-2vhost-1vm-func¶
LISP static adjacency test cases
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv4-LISP-IPv6-ICMPv6 on DUT1-DUT2, Eth-IPv6-ICMPv6 on TG-DUTn for IPv6 routing over LISPoIPv4 tunnel.
- [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv6 routing and static routes. LISPoIPv4 tunnel is configured between DUT1 and DUT2.
- [Ver] TG verification: Test ICMPv6 Echo Request packets are sent in both directions by TG on links to DUT1 and DUT2; on receive TG verifies packets for correctness and their IPv6 src-addr, dst-addr and MAC addresses.
- [Ref] Applicable standard specifications: RFC6830.
| Name | Documentation | Status |
|---|---|---|
| TC01: DUT1 and DUT2 route IPv6 bidirectionally over LISP GPE tunnel using vhost interfaces | [Top] TG-DUT1-DUT2-TG. [Enc] Eth-IPv4-LISPGPE-IPv6-ICMPv6 on DUT1-DUT2, Eth-IPv6-ICMPv6 on TG-DUTn. [Cfg] Configure IPv4 LISP static adjacencies on DUT1 and DUT2. [Ver] Case: ip6-lispgpe-ip4 - main fib, virt2lisp Make TG send ICMPv6 Echo Req between its interfaces across both DUTs and LISP GPE tunnel between them; verify IPv6 headers on received packets are correct. |
PASS |
7.3.10.14. eth2p-ethip4lispgpe-ip6base-func¶
LISP static adjacency test cases
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv4-LISP-IPv6-ICMPv6 on DUT1-DUT2, Eth-IPv6-ICMPv6 on TG-DUTn for IPv6 routing over LISPoIPv4 tunnel.
- [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv6 routing and static routes. LISPoIPv4 tunnel is configured between DUT1 and DUT2.
- [Ver] TG verification: Test ICMPv6 Echo Request packets are sent in both directions by TG on links to DUT1 and DUT2; on receive TG verifies packets for correctness and their IPv6 src-addr, dst-addr and MAC addresses.
- [Ref] Applicable standard specifications: RFC6830.
| Name | Documentation | Status |
|---|---|---|
| TC01: DUT1 and DUT2 route IPv6 bidirectionally over LISPoIPv4 tunnel | [Top] TG-DUT1-DUT2-TG. [Enc] Eth-IPv4-LISP-IPv6-ICMPv6 on DUT1-DUT2, Eth-IPv6-ICMPv6 on TG-DUTn. [Cfg] On DUT1 and DUT2 configure IPv4 LISP static adjacencies. [Ver] Make TG send ICMPv6 Echo Req between its interfaces across both DUTs and LISP tunnel between them; verify IPv6 headers on received packets are correct. [Cfg2] Reconf LISP. [Ver2] Verify packets are received again via LISP tunnel. [Ref] RFC6830. |
PASS |
7.3.10.15. eth2p-ethip4lispgpe-ip6basevrf-func¶
LISP static adjacency test cases
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv4-LISP-IPv6-ICMPv6 on DUT1-DUT2, Eth-IPv6-ICMPv6 on TG-DUTn for IPv6 routing over LISPoIPv4 tunnel.
- [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv6 routing and static routes. LISPoIPv4 tunnel is configured between DUT1 and DUT2.
- [Ver] TG verification: Test ICMPv6 Echo Request packets are sent in both directions by TG on links to DUT1 and DUT2; on receive TG verifies packets for correctness and their IPv6 src-addr, dst-addr and MAC addresses.
- [Ref] Applicable standard specifications: RFC6830.
| Name | Documentation | Status |
|---|---|---|
| TC01: DUT1 and DUT2 route IPv6 bidirectionally over LISP GPE tunnel using physical interfaces and VRF is enabled | [Top] TG-DUT1-DUT2-TG. [Enc] Eth-IPv4-LISPGPE-IPv6-ICMPv6 on DUT1-DUT2, Eth-IPv6-ICMPv6 on TG-DUTn. [Cfg] Configure IPv4 LISP static adjacencies on DUT1 and DUT2. [Ver] Case: ip6-lispgpe-ip4 - vrf, phy2lisp Make TG send ICMPv4 Echo Req between its interfaces across both DUTs and LISP GPE tunnel between them; verify IPv6 headers on received packets are correct. [Ref] RFC6830. |
PASS |
7.3.10.16. eth2p-ethip6ipsectptlispgpe-ip4base-eth-2vhost-1vm-func¶
IPv6 - ip4-ipsec-lispgpe-ip6 - main fib, virt2lisp, phy2lisp
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv6-LISPGPE-IPSec-IPv4-ICMP, Eth-IPv6-IPSec-LISPGPE-IPv4-ICMP
- [Cfg] DUT configuration: Each DUT is configured with LISP and IPsec. IPsec is in transport mode. Test cases are for IPsec configured both on RLOC interface or lisp_gpe0 interface.
- [Ver] TG verification: Packet is send from TG(if1) across the DUT1 to DUT2 where it is forwarded to TG(if2).
- [Ref] Applicable standard specifications: RFC6830, RFC4303.
| Name | Documentation | Status |
|---|---|---|
| TC01: DUT1 and DUT2 route IPv4 over Vhost to LISP GPE tunnel using IPsec (transport) on RLOC Int. | [Top] TG-DUT1-DUT2-TG. [Enc] Eth-IPv6-LISPGPE-IPSec-IPv4-ICMP on DUT1-DUT2, Eth-IPv4-ICMP on TG-DUTn. [Cfg] Configure IPv6 LISP static adjacencies on DUT1 and DUT2 with IPsec in between DUTS. Create Qemu vm on DUT1 and configure bridge between two vhosts. [Ver] Case: ip6-ipsec-lispgpe-ip4 - main fib, virt2lisp Make TG send ICMPv6 Echo Req between its interfaces across both DUTs and LISP GPE tunnel between them; verify IPv6 headers on received packets are correct. [Ref] RFC6830, RFC4303. |
PASS |
| TC02: DUT1 and DUT2 route IPv4 over Vhost to LISP GPE tunnel using IPsec (transport) on lisp_gpe0 Int. | [Top] TG-DUT1-DUT2-TG. [Enc] Eth-IPv6-IPSec-LISPGPE-IPv6-ICMPv6 on DUT1-DUT2, Eth-IPv6-ICMPv6, on TG-DUTn. [Cfg] Configure IPv6 LISP static adjacencies on DUT1 and DUT2 with IPsec in between DUTS. [Ver] Case: ip6-ipsec-lispgpe-ip4 - main fib, virt2lisp Make TG send ICMPv6 Echo Req between its interfaces across both DUTs and LISP GPE tunnel between them; verify IPv6 headers on received packets are correct. [Ref] RFC6830, RFC4303. |
PASS |
7.3.10.17. eth2p-ethip6ipsectptlispgpe-ip4base-func¶
IPv6 - ip4-ipsec-lispgpe-ip6 - main fib, virt2lisp, phy2lisp
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv6-LISPGPE-IPSec-IPv4-ICMP, Eth-IPv6-IPSec-LISPGPE-IPv4-ICMP
- [Cfg] DUT configuration: Each DUT is configured with LISP and IPsec. IPsec is in transport mode. Tests cases are for IPsec configured both on RLOC interface or lisp_gpe0 interface.
- [Ver] TG verification: Packet is send from TG(if1) across the DUT1 to DUT2 where it is forwarded to TG(if2).
- [Ref] Applicable standard specifications: RFC6830, RFC4303.
| Name | Documentation | Status |
|---|---|---|
| TC01: DUT1 and DUT2 route IPv4 bidirectionally over LISP GPE tunnel using IPsec (transport) on RLOC Int. | [Top] TG-DUT1-DUT2-TG. [Enc] Eth-IPv6-LISPGPE-IPSec-IPv4-ICMP on DUT1-DUT2, Eth-IPv4-ICMP on TG-DUTn. [Cfg] Configure IPv6 LISP static adjacencies on DUT1 and DUT2 with IPsec in between DUTS. [Ver] Make TG send ICMPv6 Echo Req between its interfaces across both DUTs and LISP GPE tunnel between them; verify IPv4 headers on received packets are correct. [Ref] RFC6830, RFC4303. |
PASS |
| TC02: DUT1 and DUT2 route IPv4 bidirectionally over LISP GPE tunnel using IPsec (transport) on lisp_gpe0 Int. | [Top] TG-DUT1-DUT2-TG. [Enc] Eth-IPv6-IPSec-LISPGPE-IPv4-ICMPv4 on DUT1-DUT2, Eth-IPv4-ICMP on TG-DUTn. [Cfg] Configure IPv6 LISP static adjacencies on DUT1 and DUT2 with IPsec in between DUTS. [Ver] Make TG send ICMPv6 Echo Req between its interfaces across both DUTs and LISP GPE tunnel between them; verify IPv4 headers on received packets are correct. [Ref] RFC6830, RFC4303. |
PASS |
7.3.10.18. eth2p-ethip6ipsectptlispgpe-ip6base-eth-2vhost-1vm-func¶
IPv6 - ip6-ipsec-lispgpe-ip6 - main fib, vrf (gpe_vni-to-vrf), phy2lisp, virt2lisp
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv6-IPSec-LISPGPE-IPv6-ICMPv6,
- [Cfg] DUT configuration: Each DUT is configured with LISP and IPsec. IPsec is in transport mode. Tests cases are for IPsec configured both on RLOC interface or lisp_gpe0 interface.
- [Ver] TG verification: Packet is send from TG(if1) across the DUT1 via VM to DUT2 where it is forwarded to TG(if2).
- [Ref] Applicable standard specifications: RFC6830, RFC4303.
| Name | Documentation | Status |
|---|---|---|
| TC01: DUT1 and DUT2 route IPv6 over Vhost to LISP GPE tunnel using IPsec (transport) on RLOC Int. | [Top] TG-DUT1-DUT2-TG. [Enc] Eth-IPv6-IPSec-LISPGPE-IPv6-ICMP on DUT1-DUT2, Eth-IPv6-ICMP on TG-DUTn. [Cfg] Configure IPv6 LISP static adjacencies on DUT1 and DUT2 with IPsec in between DUTS. Create Qemu vm on DUT1 and configure bridge between two vhosts. [Ver] Case: ip6-ipsec-lispgpe-ip6 - main fib, virt2lisp Make TG send ICMPv6 Echo Req between its interfaces across both DUTs and LISP GPE tunnel between them; verify IPv6 headers on received packets are correct. [Ref] RFC6830, RFC4303. |
PASS |
| TC02: DUT1 and DUT2 route IPv6 over Vhost to LISP GPE tunnel using IPsec (transport) on lisp_gpe0 Int. | [Top] TG-DUT1-DUT2-TG. [Enc] Eth-IPv6-IPSec-LISPGPE-IPv6-ICMPv6 on DUT1-DUT2, Eth-IPv6-ICMPv6 on TG-DUTn. [Cfg] Configure IPv6 LISP static adjacencies on DUT1 and DUT2 with IPsec in between DUTS. [Ver] Case: ip6-ipsec-lispgpe-ip6 - main fib, virt2lisp Make TG send ICMPv6 Echo Req between its interfaces across both DUTs and LISP GPE tunnel between them; verify IPv6 headers on received packets are correct. [Ref] RFC6830, RFC4303. |
PASS |
7.3.10.19. eth2p-ethip6ipsectptlispgpe-ip6base-func¶
IPv6 - ip6-ipsec-lispgpe-ip6 - main fib, vrf (gpe_vni-to-vrf), phy2lisp, virt2lisp
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv6-IPSec-LISPGPE-IPv6-ICMPv6,
- [Cfg] DUT configuration: Each DUT is configured with LISP and IPsec. IPsec is in transport mode. Tests cases are for IPsec configured both on RLOC interface or lisp_gpe0 interface.
- [Ver] TG verification: Packet is send from TG(if1) across the DUT1 to DUT2 where it is forwarded to TG(if2).
- [Ref] Applicable standard specifications: RFC6830, RFC4303.
| Name | Documentation | Status |
|---|---|---|
| TC01: DUT1 and DUT2 route IPv6 bidirectionally over LISP GPE tunnel using IPsec (transport) on RLOC Int. | [Top] TG-DUT1-DUT2-TG. [Enc] Eth-IPv6-IPSec-LISPGPE-IPv6-ICMPv6 on DUT1-DUT2, Eth-IPv6-ICMPv6 on TG-DUTn. [Cfg] Configure IPv6 LISP static adjacencies on DUT1 and DUT2 with IPsec in between DUTS. [Ver] Case: ip6-lispgpe-ipsec-ip6 - main fib, phys2lisp Make TG send ICMPv6 Echo Req between its interfaces across both DUTs and LISP GPE tunnel between them; verify IPv6 headers on received packets are correct. [Ref] RFC6830, RFC4303. |
PASS |
| TC02: DUT1 and DUT2 route IPv6 bidirectionally over LISP GPE tunnel using IPsec (transport) lisp_gpe0 Int. | [Top] TG-DUT1-DUT2-TG. [Enc] Eth-IPv6-IPSec-LISPGPE-IPv6-ICMPv6 on DUT1-DUT2, Eth-IPv6-ICMPv6 on TG-DUTn. [Cfg] Configure IPv6 LISP static adjacencies on DUT1 and DUT2 with IPsec in between DUTS. [Ver] Case: ip6-ipsec-lispgpe-ip6 - main fib, phys2lisp Make TG send ICMPv6 Echo Req between its interfaces across both DUTs and LISP GPE tunnel between them; verify IPv6 headers on received packets are correct. [Ref] RFC6830, RFC4303. |
PASS |
7.3.10.20. eth2p-ethip6lisp-l2bdbasemaclrn-func¶
l2-lispgpe-ip6 encapsulation test cases
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IP6-ICMPv6-LISPGpe-IP6
- [Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 bridge domains and neighbors. LISPoIPv6 tunnel is configured between DUT1 and DUT2.
- [Ver] TG verification: Test ICMPv6 Echo Request packets are sent in both directions by TG on links to DUT1 and DUT2; on receive TG verifies packets for correctness and their IPv6 src-addr, dst-addr and MAC addresses.
- [Ref] Applicable standard specifications: RFC6830.
| Name | Documentation | Status |
|---|---|---|
| TC01: Route IPv6 packet through LISP with Bridge Domain setup. | [Top] TG-DUT1-DUT2-TG. [Enc] Eth-IP6-ICMPv6-LISPGpe-IP6 [Cfg] Configure IPv6 LISP static adjacencies on DUT1 and DUT2. Also configure BD and assign it to LISP VNI. [Ver] Make TG send ICMPv6 Echo Req between its interfaces across both DUTs and LISP tunnel between them; verify IPv6, Ether headers on received packets are correct. [Ref] RFC6830. |
PASS |
7.3.10.21. eth2p-ethip6lispgpe-ip4base-func¶
LISP static adjacency test cases
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv6-LISP-IPv4-ICMPv4 on DUT1-DUT2, Eth-IPv4-ICMPv4 on TG-DUTn for IPv4 routing over LISPoIPv6 tunnel.
- [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv4 routing and static routes. LISPoIPv6 tunnel is configured between DUT1 and DUT2.
- [Ver] TG verification: Test ICMPv4 Echo Request packets are sent in both directions by TG on links to DUT1 and DUT2; on receive TG verifies packets for correctness and their IPv4 src-addr, dst-addr and MAC addresses.
- [Ref] Applicable standard specifications: RFC6830.
| Name | Documentation | Status |
|---|---|---|
| TC01: DUT1 and DUT2 route IPv4 bidirectionally over LISPoIPv6 tunnel | [Top] TG-DUT1-DUT2-TG. [Enc] Eth-IPv6-LISP-IPv4-ICMPv4 on DUT1-DUT2, Eth-IPv4-ICMPv4 on TG-DUTn. [Cfg] On DUT1 and DUT2 configure IPv6 LISP static adjacencies. [Ver] Make TG send ICMPv4 Echo Req between its interfaces across both DUTs and LISP tunnel between them; verify IPv4 headers on received packets are correct. [Cfg2] Reconf LISP. [Ver2] Verify packets are received again via LISP tunnel. [Ref] RFC6830. |
PASS |
7.3.10.22. eth2p-ethip6lispgpe-ip6base-eth-2vhost-1vm-func¶
ip6-lispgpe-ip6 encapsulation test cases
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv6-LISP-IPv6-ICMPv6 on DUT1-DUT2, Eth-IPv6-ICMPv6 on TG-DUTn for IPv6 routing over LISPoIPv6 tunnel.
- [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv6 routing and static routes. LISPoIPv6 tunnel is configured between DUT1 and DUT2.
- [Ver] TG verification: Test ICMPv6 Echo Request packets are sent in both directions by TG on links to DUT1 and DUT2; on receive TG verifies packets for correctness and their IPv6 src-addr, dst-addr and MAC addresses.
- [Ref] Applicable standard specifications: RFC6830.
| Name | Documentation | Status |
|---|---|---|
| TC01: DUT1 and DUT2 route IPv6 bidirectionally over LISP GPE tunnel using vhost interfaces | [Top] TG-DUT1-DUT2-TG. [Enc] Eth-IPv6-LISPGPE-IPv6-ICMPv6 on DUT1-DUT2, Eth-IPv6-ICMPv6 on TG-DUTn. [Cfg] Configure IPv6 LISP static adjacencies on DUT1 and DUT2. [Ver] Case: ip6-ipsec-lispgpe-ip6 - main fib, virt2lisp Make TG send ICMPv6 Echo Req between its interfaces across both DUTs and LISP GPE tunnel between them; verify IPv6 headers on received packets are correct. |
PASS |
7.3.10.23. eth2p-ethip6lispgpe-ip6base-func¶
ip6-lispgpe-ip6 encapsulation test cases
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv6-LISP-IPv6-ICMPv6 on DUT1-DUT2, Eth-IPv6-ICMPv6 on TG-DUTn for IPv6 routing over LISPoIPv6 tunnel.
- [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv6 routing and static routes. LISPoIPv6 tunnel is configured between DUT1 and DUT2.
- [Ver] TG verification: Test ICMPv6 Echo Request packets are sent in both directions by TG on links to DUT1 and DUT2; on receive TG verifies packets for correctness and their IPv6 src-addr, dst-addr and MAC addresses.
- [Ref] Applicable standard specifications: RFC6830.
| Name | Documentation | Status |
|---|---|---|
| TC01: DUT1 and DUT2 route IPv6 bidirectionally over LISP GPE tunnel using physical interfaces | [Top] TG-DUT1-DUT2-TG. [Enc] Eth-IPv6-LISPGPE-IPv6-ICMPv6 on DUT1-DUT2, Eth-IPv6-ICMPv6 on TG-DUTn. [Cfg] Configure IPv6 LISP static adjacencies on DUT1 and DUT2. [Ver] Case: ip6-lispgpe-ip6 - phy2lisp Make TG send ICMPv6 Echo Req between its interfaces across both DUTs and LISP GPE tunnel between them; verify IPv6 headers on received packets are correct. [Ref] RFC6830. |
PASS |
7.3.10.24. eth2p-ethip6lispgpe-ip6basevrf-eth-2vhost-1vm-func¶
ip6-lispgpe-ip6 encapsulation test cases
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv6-LISP-IPv6-ICMPv6 on DUT1-DUT2, Eth-IPv6-ICMPv6 on TG-DUTn for IPv6 routing over LISPoIPv6 tunnel.
- [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv6 routing and static routes. LISPoIPv6 tunnel is configured between DUT1 and DUT2.
- [Ver] TG verification: Test ICMPv6 Echo Request packets are sent in both directions by TG on links to DUT1 and DUT2; on receive TG verifies packets for correctness and their IPv6 src-addr, dst-addr and MAC addresses.
- [Ref] Applicable standard specifications: RFC6830.
| Name | Documentation | Status |
|---|---|---|
| TC01: DUT1 and DUT2 route IPv6 bidirectionally over LISP GPE tunnel using vhost interfaces and VRF is enabled | [Top] TG-DUT1-DUT2-TG. [Enc] Eth-IPv6-LISPGPE-IPv6-ICMPv6 on DUT1-DUT2, Eth-IPv6-ICMPv6 on TG-DUTn. [Cfg] Configure IPv6 LISP static adjacencies on DUT1 and DUT2. [Ver] Case: ip6-lispgpe-ip6 - vrf, virt2lisp Make TG send ICMPv6 Echo Req between its interfaces across both DUTs and LISP GPE tunnel between them; verify IPv6 headers on received packets are correct. [Ref] RFC6830. |
PASS |
7.3.10.25. eth2p-ethip6lispgpe-ip6basevrf-func¶
ip6-lispgpe-ip6 encapsulation test cases
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv6-LISP-IPv6-ICMPv6 on DUT1-DUT2, Eth-IPv6-ICMPv6 on TG-DUTn for IPv6 routing over LISPoIPv6 tunnel.
- [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv6 routing and static routes. LISPoIPv6 tunnel is configured between DUT1 and DUT2.
- [Ver] TG verification: Test ICMPv6 Echo Request packets are sent in both directions by TG on links to DUT1 and DUT2; on receive TG verifies packets for correctness and their IPv6 src-addr, dst-addr and MAC addresses.
- [Ref] Applicable standard specifications: RFC6830.
| Name | Documentation | Status |
|---|---|---|
| TC01: DUT1 and DUT2 route IPv6 bidirectionally over LISP GPE tunnel using physical interfaces and VRF is enabled | [Top] TG-DUT1-DUT2-TG. [Enc] Eth-IPv6-LISPGPE-IPv6-ICMPv6 on DUT1-DUT2, Eth-IPv6-ICMPv6 on TG-DUTn. [Cfg] Configure IPv6 LISP static adjacencies on DUT1 and DUT2. [Ver] Case: ip6-lispgpe-ip6 - vrf, phy2lisp Make TG send ICMPv6 Echo Req between its interfaces across both DUTs and LISP GPE tunnel between them; verify IPv6 headers on received packets are correct. [Ref] RFC6830. |
PASS |